H3C S12500CR LSXM1SUPKR1 Card Manual-APW101

HomeSupportResource CenterSwitchesH3C S12500R Switch Router SeriesH3C S12500R Switch Router SeriesTechnical DocumentsInstall & UpgradeMPU Card ManualsH3C S12500CR LSXM1SUPKR1 Card Manual-APW101
Download Book
Table of Contents
Related Documents

LSXM1SUPKR1 supervisor engine unit

1  Identifier

The module identifier LSXM1SUPKR1 is at the far right of the front panel.

2  Specifications

Figure 1 Front panel

(1) 1PPS/ToD time synchronization port

(2) SMB clock output port

(3) SMB clock input port

(4) USB port

(5) Console port (CONSOLE)

(6) GE SFP port for management and upgrade

(7) 10/100/1000BASE-T port LED (LINK)

(8) 10/100/1000BASE-T port for management and upgrade

(9) Active/standby status LED

(10) 10/100/1000BASE-T port LED (ACT)

(11) GE SFP port LED

(12) Mini USB console port

(13) Slot status LED

 

Table 1 Module specifications

Item

Specification

Processor

Intel processor (Quad Core) @ 2.2 GHz

DDR

32GB DDR4 (two DIMM slots)

Flash

4GB EMMC

NVRAM

512 KB

SSD

240 GB (SATA)

Power consumption

50 W to 60 W

LED

·         28 × slot status LEDs

·         2 × 10/100/1000BASE-T management and upgrade port LEDs

·         2 × GE SFP management and upgrade port LEDs

·         1 × active/standby status LED

For more information about the LEDs, see Table 2 and Table 3.

Connector

·         RJ-45

·         LC

·         USB (Type A)

·         Mini-USB (Type AB)

Port

·         1 × RJ-45 console port

·         1 × mini-USB console port

·         2 × 10/100/1000BASE-T ports for management and upgrade

·         2 × GE SFP ports for management and upgrade

·         1 × USB port (USB 3.0, Host port)

·         2 × 1PPS/ToD time synchronization ports

·         2 × SMB clock input ports

·         2 × SMB clock output ports

Transmission rate

·         Console port: 9600 bps (default) to 115200 bps

·         10/100/1000BASE-T port: 10/100/1000 Mbps

·         GE SFP port: 1000 Mbps

Transmission medium and max transmission distance of the console port

15 m (49.21 ft) over asynchronous serial cable

Transmission medium and max transmission distance of the 10/100/1000BASE-T port

100 m (328.08 ft) over category-5 UTP

Compatible device models

S12508CR/S12516CR

 

Table 2 LED description (1)

LED

Mark

Status

Description

Slot status LED

Slot 2 to 28

Off

The module in the slot is faulty or the slot is empty.

Flashing green (0.5 Hz)

The module in the slot is operating correctly.

Flashing green (4 Hz)

The module in the slot is loading software.

If the LED keeps in this state, the software version of the module does not match that of the device.

Steady red

An alarm has occurred.

GE SFP management and upgrade port LED

LINK/ACT

Off

No link is present on the port.

Flashing green

The port is sending or receiving data.

Steady green

A link is present on the port.

Active/standby status LED

ACT

Off

The MPU is in standby state.

Steady green

The MPU is in active state.

 

Table 3 LED description (2)

10/100/1000BASE-T port LED

Description

Link

ACT

Off

Off

No link is present.

Steady green

Off

A 1000 Mbps link is present.

Steady orange

Off

A 10/100 Mbps link is present.

Steady green

Flashing yellow

The port is receiving or sending data at 1000 Mbps.

Steady orange

Flashing yellow

The port is receiving or sending data at 10/100 Mbps.

 

IMPORTANT

IMPORTANT:

·      To verify compatibility of the module with the software release you are using, see the release notes.

·      You can access and configure the device through the RJ-45 console port or the mini-USB console port. Only one port is active at a time.

·      To connect a USB device to the module, make sure the USB device is in good condition.

·      Set the same speed and duplex mode for a management Ethernet interface and its peer port.

·      If multiple management ports are connected to one remote switch, you must assign their peer ports to different VLANs on the remote switch. Login or file transfer will fail if the peer ports are in the same VLAN.

·      For information about transceiver modules and cables available for the module, see H3C S12500R Switch Routers Modules and Transceiver Modules Compatibility Matrixes.

 

3  Related documentation

For module installation, see the H3C S12500CR Switch Routers Installation Guide.

For software upgrade, see the release notes for the device.

 

 

Copyright © 2020 New H3C Technologies Co., Ltd.

The information in this document is subject to change without notice.