H3C S10500X Release 7577P01 System Log Message Reference-6W100

HomeSupportResource CenterSwitchesH3C S10500X Switch SeriesH3C S10500X Switch SeriesTechnical DocumentsMaintainMessage ReferencesH3C S10500X Release 7577P01 System Log Message Reference-6W100

 

S10500X System Log Messages Reference

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Copyright © 2019 New H3C Technologies Co., Ltd. All rights reserved.

No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New H3C Technologies Co., Ltd.

Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this document are the property of their respective owners.

The information in this document is subject to change without notice.


Contents

Introduction· 1

System log message format 1

Managing and obtaining system log messages· 3

Obtaining log messages from the console terminal 3

Obtaining log messages from the log buffer 3

Obtaining log messages from a monitor terminal 3

Obtaining log messages from the log file· 4

Obtaining log messages from a log host 4

Software module list 4

Using this document 8

AAA messages· 8

AAA_FAILURE· 9

AAA_LAUNCH· 9

AAA_SUCCESS· 10

ACL messages· 10

ACL_ACCELERATE_NO_RES· 10

ACL_ACCELERATE_NONCONTIGUOUSMASK· 11

ACL_ACCELERATE_NOT_SUPPORT· 11

ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP· 11

ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG·· 12

ACL_ACCELERATE_UNK_ERR· 12

ACL_IPV6_STATIS_INFO·· 12

ACL_NO_MEM·· 13

ACL_STATIS_INFO·· 13

ANCP messages· 13

ANCP_INVALID_PACKET· 14

API 14

DRVPLAT/2/DrvDebug· 14

DRVPLAT/4/DrvDebug· 15

DRVPLAT/4/DrvDebug· 15

APMGR messages· 15

APMGR_AC_MEM_ALERT· 16

APMGR_ADD_AP_FAIL· 16

APMGR_ADDBAC_INFO·· 16

APMGR_AP_OFFLINE· 17

APMGR_AP_ONLINE· 17

APMGR_CWC_IMG_DOWNLOAD_COMPLETE· 17

APMGR_CWC_IMG_DOWNLOAD_START· 18

APMGR_CWC_IMG_NO_ENOUGH_SPACE· 18

APMGR_CWC_LOCAL_AC_DOWN· 19

APMGR_CWC_LOCAL_AC_UP· 19

APMGR_CWC_REBOOT· 20

APMGR_CWC_RUN_DOWNLOAD_COMPLETE· 20

APMGR_CWC_RUN_DOWNLOAD_START· 20

APMGR_CWC_RUN_NO_ENOUGH_SPACE· 21

APMGR_CWC_TUNNEL_DOWN· 21

APMGR_CWC_TUNNEL_UP· 22

APMGR_CWS_IMG_DOWNLOAD_COMPLETE· 22

APMGR_CWS_IMG_DOWNLOAD_START· 22

APMGR_CWS_LOCAL_AC_DOWN· 23

APMGR_CWS_LOCAL_AC_UP· 23

APMGR_CWS_RUN_DOWNLOAD_COMPLETE· 24

APMGR_CWS_RUN_DOWNLOAD_START· 24

APMGR_CWS_TUNNEL_DOWN· 25

APMGR_CWS_TUNNEL_UP· 25

APMGR_DELBAC_INFO·· 26

APMGR_LOCAL_AC_OFFLINE· 26

APMGR_LOCAL_AC_ONLINE· 26

ARP messages· 26

ARP_ACTIVE_ACK_NO_REPLY· 27

ARP_ACTIVE_ACK_NOREQUESTED_REPLY· 27

ARP_BINDRULETOHW_FAILED·· 28

ARP_DETECTION_LOG·· 28

ARP_DUPLICATE_IPADDR_DETECT· 29

ARP_DYNAMIC· 29

ARP_DYNAMIC_IF· 30

ARP_DYNAMIC_SLOT· 30

ARP_ENTRY_CONFLICT· 31

ARP_HOST_IP_CONFLICT· 31

ARP_LOCALPROXY_ENABLE_FAILED·· 32

ARP_RATE_EXCEEDED·· 32

ARP_RATELIMIT_NOTSUPPORT· 33

ARP_SENDER_IP_INVALID·· 33

ARP_SENDER_MAC_INVALID·· 34

ARP_SENDER_SMACCONFLICT· 34

ARP_SENDER_SMACCONFLICT_VSI 35

ARP_SRC_MAC_FOUND_ATTACK· 35

ARP_SUP_ENABLE_FAILED·· 36

ARP_TARGET_IP_INVALID·· 36

ARP_THRESHOLD_REACHED·· 36

ARP_USER_DUPLICATE_IPADDR_DETECT· 37

DUPIFIP· 37

DUPIP· 38

DUPVRRPIP· 38

ATK messages· 38

ATK_ICMP_ADDRMASK_REQ·· 39

ATK_ICMP_ADDRMASK_REQ_RAW·· 40

ATK_ICMP_ADDRMASK_REQ_RAW_SZ· 41

ATK_ICMP_ADDRMASK_REQ_SZ· 42

ATK_ICMP_ADDRMASK_RPL· 43

ATK_ICMP_ADDRMASK_RPL_RAW·· 44

ATK_ICMP_ADDRMASK_RPL_RAW_SZ· 45

ATK_ICMP_ADDRMASK_RPL_SZ· 46

ATK_ICMP_ECHO_REQ·· 47

ATK_ICMP_ECHO_REQ_RAW·· 48

ATK_ICMP_ECHO_REQ_RAW_SZ· 49

ATK_ICMP_ECHO_REQ_SZ· 50

ATK_ICMP_ECHO_RPL· 51

ATK_ICMP_ECHO_RPL_RAW·· 52

ATK_ICMP_ECHO_RPL_RAW_SZ· 53

ATK_ICMP_ECHO_RPL_SZ· 54

ATK_ICMP_FLOOD·· 55

ATK_ICMP_FLOOD_SZ· 55

ATK_ICMP_INFO_REQ·· 56

ATK_ICMP_INFO_REQ_RAW·· 57

ATK_ICMP_INFO_REQ_RAW_SZ· 58

ATK_ICMP_INFO_REQ_SZ· 59

ATK_ICMP_INFO_RPL· 60

ATK_ICMP_INFO_RPL_RAW·· 61

ATK_ICMP_INFO_RPL_RAW_SZ· 62

ATK_ICMP_INFO_RPL_SZ· 63

ATK_ICMP_LARGE· 64

ATK_ICMP_LARGE_RAW·· 64

ATK_ICMP_LARGE_RAW_SZ· 65

ATK_ICMP_LARGE_SZ· 65

ATK_ICMP_PARAPROBLEM·· 66

ATK_ICMP_PARAPROBLEM_RAW·· 67

ATK_ICMP_PARAPROBLEM_RAW_SZ· 68

ATK_ICMP_PARAPROBLEM_SZ· 69

ATK_ICMP_PINGOFDEATH· 70

ATK_ICMP_PINGOFDEATH_RAW·· 71

ATK_ICMP_PINGOFDEATH_RAW_SZ· 71

ATK_ICMP_PINGOFDEATH_SZ· 72

ATK_ICMP_REDIRECT· 73

ATK_ICMP_REDIRECT_RAW·· 74

ATK_ICMP_REDIRECT_RAW_SZ· 75

ATK_ICMP_REDIRECT_SZ· 76

ATK_ICMP_SMURF· 77

ATK_ICMP_SMURF_RAW·· 78

ATK_ICMP_SMURF_RAW_SZ· 79

ATK_ICMP_SMURF_SZ· 80

ATK_ICMP_SOURCEQUENCH· 81

ATK_ICMP_SOURCEQUENCH_RAW·· 82

ATK_ICMP_SOURCEQUENCH_RAW_SZ· 83

ATK_ICMP_SOURCEQUENCH_SZ· 84

ATK_ICMP_TIMEEXCEED·· 85

ATK_ICMP_TIMEEXCEED_RAW·· 86

ATK_ICMP_TIMEEXCEED_RAW_SZ· 87

ATK_ICMP_TIMEEXCEED_SZ· 88

ATK_ICMP_TRACEROUTE· 89

ATK_ICMP_TRACEROUTE_RAW·· 90

ATK_ICMP_TRACEROUTE_RAW_SZ· 90

ATK_ICMP_TRACEROUTE_SZ· 91

ATK_ICMP_TSTAMP_REQ·· 92

ATK_ICMP_TSTAMP_REQ_RAW·· 93

ATK_ICMP_TSTAMP_REQ_RAW_SZ· 94

ATK_ICMP_TSTAMP_REQ_SZ· 95

ATK_ICMP_TSTAMP_RPL· 96

ATK_ICMP_TSTAMP_RPL_RAW·· 97

ATK_ICMP_TSTAMP_RPL_RAW_SZ· 98

ATK_ICMP_TSTAMP_RPL_SZ· 99

ATK_ICMP_TYPE· 100

ATK_ICMP_TYPE_RAW·· 101

ATK_ICMP_TYPE_RAW_SZ· 102

ATK_ICMP_TYPE_SZ· 103

ATK_ICMP_UNREACHABLE· 104

ATK_ICMP_UNREACHABLE_RAW·· 105

ATK_ICMP_UNREACHABLE_RAW_SZ· 106

ATK_ICMP_UNREACHABLE_SZ· 107

ATK_ICMPV6_DEST_UNREACH· 108

ATK_ICMPV6_DEST_UNREACH_RAW·· 109

ATK_ICMPV6_DEST_UNREACH_RAW_SZ· 109

ATK_ICMPV6_DEST_UNREACH_SZ· 110

ATK_ICMPV6_ECHO_REQ·· 111

ATK_ICMPV6_ECHO_REQ_RAW·· 112

ATK_ICMPV6_ECHO_REQ_RAW_SZ· 112

ATK_ICMPV6_ECHO_REQ_SZ· 113

ATK_ICMPV6_ECHO_RPL· 114

ATK_ICMPV6_ECHO_RPL_RAW·· 115

ATK_ICMPV6_ECHO_RPL_RAW_SZ· 115

ATK_ICMPV6_ECHO_RPL_SZ· 116

ATK_ICMPV6_FLOOD·· 117

ATK_ICMPV6_FLOOD_SZ· 117

ATK_ICMPV6_GROUPQUERY· 118

ATK_ICMPV6_GROUPQUERY_RAW·· 119

ATK_ICMPV6_GROUPQUERY_RAW_SZ· 119

ATK_ICMPV6_GROUPQUERY_SZ· 120

ATK_ICMPV6_GROUPREDUCTION· 121

ATK_ICMPV6_GROUPREDUCTION_RAW·· 122

ATK_ICMPV6_GROUPREDUCTION_RAW_SZ· 122

ATK_ICMPV6_GROUPREDUCTION_SZ· 123

ATK_ICMPV6_GROUPREPORT· 124

ATK_ICMPV6_GROUPREPORT_RAW·· 125

ATK_ICMPV6_GROUPREPORT_RAW_SZ· 125

ATK_ICMPV6_GROUPREPORT_SZ· 126

ATK_ICMPV6_LARGE· 127

ATK_ICMPV6_LARGE_RAW·· 127

ATK_ICMPV6_LARGE_RAW_SZ· 128

ATK_ICMPV6_LARGE_SZ· 128

ATK_ICMPV6_PACKETTOOBIG·· 129

ATK_ICMPV6_PACKETTOOBIG_RAW·· 130

ATK_ICMPV6_PACKETTOOBIG_RAW_SZ· 130

ATK_ICMPV6_PACKETTOOBIG_SZ· 131

ATK_ICMPV6_PARAPROBLEM·· 132

ATK_ICMPV6_PARAPROBLEM_RAW·· 133

ATK_ICMPV6_PARAPROBLEM_RAW_SZ· 133

ATK_ICMPV6_PARAPROBLEM_SZ· 134

ATK_ICMPV6_TIMEEXCEED·· 135

ATK_ICMPV6_TIMEEXCEED_RAW·· 136

ATK_ICMPV6_TIMEEXCEED_RAW_SZ· 136

ATK_ICMPV6_TIMEEXCEED_SZ· 137

ATK_ICMPV6_TRACEROUTE· 138

ATK_ICMPV6_TRACEROUTE_RAW·· 139

ATK_ICMPV6_TRACEROUTE_RAW_SZ· 140

ATK_ICMPV6_TRACEROUTE_SZ· 141

ATK_ICMPV6_TYPE· 142

ATK_ICMPV6_TYPE _RAW_SZ· 143

ATK_ICMPV6_TYPE_RAW·· 143

ATK_ICMPV6_TYPE_SZ· 144

ATK_IP_OPTION· 145

ATK_IP_OPTION_RAW·· 146

ATK_IP_OPTION_RAW_SZ· 147

ATK_IP_OPTION_SZ· 148

ATK_IP4_ACK_FLOOD·· 149

ATK_IP4_ACK_FLOOD_SZ· 149

ATK_IP4_DIS_PORTSCAN· 150

ATK_IP4_DIS_PORTSCAN_SZ· 150

ATK_IP4_DNS_FLOOD·· 151

ATK_IP4_DNS_FLOOD_SZ· 151

ATK_IP4_FIN_FLOOD·· 152

ATK_IP4_FIN_FLOOD_SZ· 152

ATK_IP4_FRAGMENT· 153

ATK_IP4_FRAGMENT_RAW·· 154

ATK_IP4_FRAGMENT_RAW_SZ· 155

ATK_IP4_FRAGMENT_SZ· 156

ATK_IP4_HTTP_FLOOD·· 157

ATK_IP4_HTTP_FLOOD_SZ· 157

ATK_IP4_IMPOSSIBLE· 158

ATK_IP4_IMPOSSIBLE_RAW·· 159

ATK_IP4_IMPOSSIBLE_RAW_SZ· 160

ATK_IP4_IMPOSSIBLE_SZ· 161

ATK_IP4_IPSWEEP· 162

ATK_IP4_IPSWEEP_SZ· 162

ATK_IP4_PORTSCAN· 163

ATK_IP4_PORTSCAN_SZ· 163

ATK_IP4_RST_FLOOD·· 164

ATK_IP4_RST_FLOOD_SZ· 164

ATK_IP4_SYN_FLOOD·· 165

ATK_IP4_SYN_FLOOD_SZ· 165

ATK_IP4_SYNACK_FLOOD·· 166

ATK_IP4_SYNACK_FLOOD_SZ· 166

ATK_IP4_TCP_ALLFLAGS· 167

ATK_IP4_TCP_ALLFLAGS_RAW·· 168

ATK_IP4_TCP_ALLFLAGS_RAW_SZ· 168

ATK_IP4_TCP_ALLFLAGS_SZ· 169

ATK_IP4_TCP_FINONLY· 170

ATK_IP4_TCP_FINONLY_RAW·· 171

ATK_IP4_TCP_FINONLY_RAW_SZ· 171

ATK_IP4_TCP_FINONLY_SZ· 172

ATK_IP4_TCP_INVALIDFLAGS· 173

ATK_IP4_TCP_INVALIDFLAGS_RAW·· 174

ATK_IP4_TCP_INVALIDFLAGS_RAW_SZ· 175

ATK_IP4_TCP_INVALIDFLAGS_SZ· 176

ATK_IP4_TCP_LAND·· 177

ATK_IP4_TCP_LAND_RAW·· 178

ATK_IP4_TCP_LAND_RAW_SZ· 178

ATK_IP4_TCP_LAND_SZ· 179

ATK_IP4_TCP_NULLFLAG·· 180

ATK_IP4_TCP_NULLFLAG_RAW·· 181

ATK_IP4_TCP_NULLFLAG_RAW_SZ· 181

ATK_IP4_TCP_NULLFLAG_SZ· 182

ATK_IP4_TCP_SYNFIN· 183

ATK_IP4_TCP_SYNFIN_RAW·· 184

ATK_IP4_TCP_SYNFIN_RAW_SZ· 184

ATK_IP4_TCP_SYNFIN_SZ· 185

ATK_IP4_TCP_WINNUKE· 186

ATK_IP4_TCP_WINNUKE_RAW·· 187

ATK_IP4_TCP_WINNUKE_RAW_SZ· 188

ATK_IP4_TCP_WINNUKE_SZ· 189

ATK_IP4_TEARDROP· 190

ATK_IP4_TEARDROP_RAW·· 191

ATK_IP4_TEARDROP_RAW_SZ· 192

ATK_IP4_TEARDROP_SZ· 193

ATK_IP4_TINY_FRAGMENT· 194

ATK_IP4_TINY_FRAGMENT_RAW·· 195

ATK_IP4_TINY_FRAGMENT_RAW_SZ· 196

ATK_IP4_TINY_FRAGMENT_SZ· 197

ATK_IP4_UDP_BOMB· 198

ATK_IP4_UDP_BOMB_RAW·· 199

ATK_IP4_UDP_BOMB_RAW_SZ· 200

ATK_IP4_UDP_BOMB_SZ· 201

ATK_IP4_UDP_FLOOD·· 202

ATK_IP4_UDP_FLOOD_SZ· 202

ATK_IP4_UDP_FRAGGLE· 203

ATK_IP4_UDP_FRAGGLE_RAW·· 204

ATK_IP4_UDP_FRAGGLE_RAW_SZ· 204

ATK_IP4_UDP_FRAGGLE_SZ· 205

ATK_IP4_UDP_SNORK· 206

ATK_IP4_UDP_SNORK_RAW·· 207

ATK_IP4_UDP_SNORK_RAW_SZ· 207

ATK_IP4_UDP_SNORK_SZ· 208

ATK_IP6_ACK_FLOOD·· 209

ATK_IP6_ACK_FLOOD_SZ· 209

ATK_IP6_DIS_PORTSCAN· 210

ATK_IP6_DIS_PORTSCAN_SZ· 210

ATK_IP6_DNS_FLOOD·· 211

ATK_IP6_DNS_FLOOD_SZ· 211

ATK_IP6_FIN_FLOOD·· 212

ATK_IP6_FIN_FLOOD_SZ· 212

ATK_IP6_FRAGMENT· 213

ATK_IP6_FRAGMENT_RAW·· 214

ATK_IP6_FRAGMENT_RAW_SZ· 215

ATK_IP6_FRAGMENT_SZ· 216

ATK_IP6_HTTP_FLOOD·· 217

ATK_IP6_HTTP_FLOOD_SZ· 217

ATK_IP6_IMPOSSIBLE· 218

ATK_IP6_IMPOSSIBLE_RAW·· 219

ATK_IP6_IMPOSSIBLE_RAW_SZ· 220

ATK_IP6_IMPOSSIBLE_SZ· 221

ATK_IP6_IPSWEEP· 221

ATK_IP6_IPSWEEP_SZ· 222

ATK_IP6_PORTSCAN· 222

ATK_IP6_PORTSCAN_SZ· 223

ATK_IP6_RST_FLOOD·· 223

ATK_IP6_RST_FLOOD_SZ· 224

ATK_IP6_SYN_FLOOD·· 224

ATK_IP6_SYN_FLOOD_SZ· 225

ATK_IP6_SYNACK_FLOOD·· 225

ATK_IP6_SYNACK_FLOOD_SZ· 226

ATK_IP6_TCP_ALLFLAGS· 226

ATK_IP6_TCP_ALLFLAGS_RAW·· 227

ATK_IP6_TCP_ALLFLAGS_RAW_SZ· 227

ATK_IP6_TCP_ALLFLAGS_SZ· 228

ATK_IP6_TCP_FINONLY· 229

ATK_IP6_TCP_FINONLY_RAW·· 229

ATK_IP6_TCP_FINONLY_RAW_SZ· 230

ATK_IP6_TCP_FINONLY_SZ· 230

ATK_IP6_TCP_INVALIDFLAGS· 231

ATK_IP6_TCP_INVALIDFLAGS_RAW·· 232

ATK_IP6_TCP_INVALIDFLAGS_RAW_SZ· 233

ATK_IP6_TCP_INVALIDFLAGS_SZ· 234

ATK_IP6_TCP_LAND·· 235

ATK_IP6_TCP_LAND_RAW·· 235

ATK_IP6_TCP_LAND_RAW_SZ· 236

ATK_IP6_TCP_LAND_SZ· 236

ATK_IP6_TCP_NULLFLAG·· 237

ATK_IP6_TCP_NULLFLAG_RAW·· 237

ATK_IP6_TCP_NULLFLAG_RAW_SZ· 238

ATK_IP6_TCP_NULLFLAG_SZ· 238

ATK_IP6_TCP_SYNFIN· 239

ATK_IP6_TCP_SYNFIN_RAW·· 239

ATK_IP6_TCP_SYNFIN_RAW_SZ· 240

ATK_IP6_TCP_SYNFIN_SZ· 240

ATK_IP6_TCP_WINNUKE· 241

ATK_IP6_TCP_WINNUKE_RAW·· 241

ATK_IP6_TCP_WINNUKE_RAW_SZ· 242

ATK_IP6_TCP_WINNUKE_SZ· 242

ATK_IP6_UDP_FLOOD·· 243

ATK_IP6_UDP_FLOOD_SZ· 243

ATK_IP6_UDP_FRAGGLE· 244

ATK_IP6_UDP_FRAGGLE_RAW·· 244

ATK_IP6_UDP_FRAGGLE_RAW_SZ· 245

ATK_IP6_UDP_FRAGGLE_SZ· 245

ATK_IP6_UDP_SNORK· 246

ATK_IP6_UDP_SNORK_RAW·· 246

ATK_IP6_UDP_SNORK_RAW_SZ· 247

ATK_IP6_UDP_SNORK_SZ· 247

ATK_IPOPT_ABNORMAL· 248

ATK_IPOPT_ABNORMAL_RAW·· 249

ATK_IPOPT_ABNORMAL_RAW_SZ· 250

ATK_IPOPT_ABNORMAL_SZ· 251

ATK_IPOPT_LOOSESRCROUTE· 252

ATK_IPOPT_LOOSESRCROUTE_RAW·· 253

ATK_IPOPT_LOOSESRCROUTE_RAW_SZ· 254

ATK_IPOPT_LOOSESRCROUTE_SZ· 255

ATK_IPOPT_RECORDROUTE· 256

ATK_IPOPT_RECORDROUTE_RAW·· 257

ATK_IPOPT_RECORDROUTE_RAW_SZ· 258

ATK_IPOPT_RECORDROUTE_SZ· 259

ATK_IPOPT_ROUTEALERT· 260

ATK_IPOPT_ROUTEALERT_RAW·· 261

ATK_IPOPT_ROUTEALERT_RAW_SZ· 262

ATK_IPOPT_ROUTEALERT_SZ· 263

ATK_IPOPT_SECURITY· 264

ATK_IPOPT_SECURITY_RAW·· 265

ATK_IPOPT_SECURITY_RAW_SZ· 266

ATK_IPOPT_SECURITY_SZ· 267

ATK_IPOPT_STREAMID·· 268

ATK_IPOPT_STREAMID_RAW·· 269

ATK_IPOPT_STREAMID_RAW_SZ· 270

ATK_IPOPT_STREAMID_SZ· 271

ATK_IPOPT_STRICTSRCROUTE· 272

ATK_IPOPT_STRICTSRCROUTE_RAW·· 273

ATK_IPOPT_STRICTSRCROUTE_RAW_SZ· 274

ATK_IPOPT_STRICTSRCROUTE_SZ· 275

ATK_IPOPT_TIMESTAMP· 276

ATK_IPOPT_TIMESTAMP_RAW·· 277

ATK_IPOPT_TIMESTAMP_RAW_SZ· 278

ATK_IPOPT_TIMESTAMP_SZ· 279

ATK_IPV6_EXT_HEADER· 280

ATK_IPV6_EXT_HEADER_RAW·· 281

ATK_IPV6_EXT_HEADER_RAW_SZ· 281

ATK_IPV6_EXT_HEADER_SZ· 282

ATM·· 282

ATM_PVCDOWN· 283

ATM_PVCUP· 284

BFD messages· 284

BFD_CHANGE_FSM·· 284

BFD_REACHED_UPPER_LIMIT· 285

BGP messages· 285

BGP_EXCEED_ROUTE_LIMIT· 285

BGP_REACHED_THRESHOLD·· 286

BGP_LOG_ROUTE_FLAP· 286

BGP_MEM_ALERT· 287

BGP_PEER_LICENSE_REACHED·· 287

BGP_ROUTE_LICENSE_REACHED·· 287

BGP_STATE_CHANGED·· 288

BLS messages· 288

BLS_ENTRY_ADD·· 288

BLS_ENTRY_DEL· 289

BLS_IPV6_ENTRY_ADD·· 289

BLS_IPV6_ENTRY_DEL· 290

CFD messages· 290

CFD_CROSS_CCM·· 290

CFD_ERROR_CCM·· 291

CFD_LOST_CCM·· 291

CFD_RECEIVE_CCM·· 292

CFGMAN messages· 293

CFGMAN_ARCHIVE_SCP_FAIL· 293

CFGMAN_CFGCHANGED·· 293

CFGMAN_EXIT_FROM_CONFIGURE· 294

CFGMAN_OPTCOMPLETION· 294

CONNLMT messages· 295

CONNLMT_IPV4_OVERLOAD·· 296

CONNLMT_IPV4_RECOVER· 297

CONNLMT_IPV6_OVERLOAD·· 298

CONNLMT_IPV6_RECOVER· 299

DEV messages· 299

BOARD_INSERTED·· 300

BOARD_REBOOT· 300

BOARD_REMOVED·· 300

BOARD_STATE_FAULT· 301

BOARD_STATE_NORMAL· 301

BOARD_STATE_STARTING·· 301

CFCARD_INSERTED·· 302

CFCARD_REMOVED·· 302

CHASSIS_REBOOT· 302

DEV_CLOCK_CHANGE· 303

DEV_FAULT_TOOLONG·· 303

DYINGGASP· 303

FAN_ABSENT· 304

FAN_DIRECTION_NOT_PREFERRED·· 304

FAN_FAILED·· 305

FAN_RECOVERED·· 305

MAD_DETECT· 306

POWER_ABSENT· 306

POWER_FAILED·· 307

POWER_MONITOR_ABSENT· 308

POWER_MONITOR_FAILED·· 309

POWER_MONITOR_RECOVERED·· 309

POWER_RECOVERED·· 310

RPS_ABSENT· 310

RPS_NORMAL· 311

SUBCARD_FAULT· 311

SUBCARD_INSERTED·· 312

SUBCARD_REBOOT· 312

SUBCARD_REMOVED·· 312

SYSTEM_REBOOT· 313

TEMPERATURE_ALARM·· 314

TEMPERATURE_LOW·· 315

TEMPERATURE_NORMAL· 316

TEMPERATURE_SHUTDOWN· 317

TEMPERATURE_WARNING·· 318

VCHK_VERSION_INCOMPATIBLE· 319

DHCP· 319

DHCP_NOTSUPPORTED·· 319

DHCP_NORESOURCES· 319

DHCPR·· 320

DHCPR_SERVERCHANGE· 320

DHCPR_SWITCHMASTER· 320

DHCPS messages· 320

DHCPS_ALLOCATE_IP· 321

DHCPS_CONFLICT_IP· 321

DHCPS_EXTEND_IP· 322

DHCPS_FILE· 322

DHCPS_RECLAIM_IP· 322

DHCPS_VERIFY_CLASS· 323

DHCPS6 messages· 323

DHCPS6_ALLOCATE_ADDRESS· 323

DHCPS6_ALLOCATE_PREFIX· 324

DHCPS6_CONFLICT_ADDRESS· 324

DHCPS6_EXTEND_ADDRESS· 325

DHCPS6_EXTEND_PREFIX· 325

DHCPS6_FILE· 326

DHCPS6_RECLAIM_ADDRESS· 326

DHCPS6_RECLAIM_PREFIX· 327

DHCPSP4· 327

DHCPSP4_FILE· 327

DHCPSP6· 327

DHCPSP6_FILE· 328

DIAG messages· 328

CPU_MINOR_RECOVERY· 328

CPU_MINOR_THRESHOLD·· 328

CPU_SEVERE_RECOVERY· 329

CPU_SEVERE_THRESHOLD·· 329

MEM_ALERT· 330

MEM_BELOW_THRESHOLD·· 331

MEM_EXCEED_THRESHOLD·· 331

DLDP messages· 332

DLDP_AUTHENTICATION_FAILED·· 332

DLDP_LINK_BIDIRECTIONAL· 332

DLDP_LINK_SHUTMODECHG·· 333

DLDP_LINK_UNIDIRECTIONAL· 333

DLDP_NEIGHBOR_AGED·· 334

DLDP_NEIGHBOR_CONFIRMED·· 334

DLDP_NEIGHBOR_DELETED·· 335

DOT1X messages· 335

DOT1X_CONFIG_NOTSUPPORT· 335

DOT1X_LOGIN_FAILURE· 336

DOT1X_LOGIN_SUCC· 336

DOT1X_LOGIN_SUCC (in open mode) 337

DOT1X_LOGOFF· 337

DOT1X_LOGOFF (in open mode) 338

DOT1X_LOGOFF_ABNORMAL· 338

DOT1X_LOGOFF_ABNORMAL (in open mode) 339

DOT1X_MACBINDING_EXIST· 339

DOT1X_NOTENOUGH_EADFREEIP_RES· 340

DOT1X_NOTENOUGH_EADFREERULE_RES· 340

DOT1X_NOTENOUGH_EADMACREDIR_RES· 340

DOT1X_NOTENOUGH_EADPORTREDIR_RES· 341

DOT1X_NOTENOUGH_ENABLEDOT1X_RES· 341

DOT1X_PEXAGG_NOMEMBER_RES· 341

DOT1X_SMARTON_FAILURE· 342

DOT1X_UNICAST_NOT_EFFECTIVE· 342

DRNI 342

DRNI_IFEVENT_DR_BIND·· 343

DRNI_IFEVENT_DR_GLOBALDOWN· 343

DRNI_IFEVENT_DR_GLOBALUP· 343

DRNI_IFEVENT_DR_NOSELECTED·· 344

DRNI_IFEVENT_DR_PEER_NOSELECTED·· 344

DRNI_IFEVENT_DR_PEER_SELECTED·· 344

DRNI_IFEVENT_DR_SELECTED·· 345

DRNI_IFEVENT_DR_UNBIND·· 345

DRNI_IFEVENT_IPP_BIND·· 345

DRNI_IFEVENT_IPP_DOWN· 346

DRNI_IFEVENT_IPP_UNBIND·· 346

DRNI_IFEVENT_IPP_UP· 346

DRNI_IPP_BLOCK· 347

DRNI_IPP_UNBLOCK· 347

DRNI_KEEPALIVEINTERVAL_MISMATCH· 347

DRNI_KEEPALIVELINK_DOWN· 348

DRNI_KEEPALIVELINK_UP· 348

DRNI_SECONDARY_MADDOWN· 348

DRNI_SYSEVENT_DEVICEROLE_CHANGE· 349

DRNI_SYSEVENT_MAC_CHANGE· 349

DRNI_SYSEVENT_NUMBER_CHANGE· 349

DRNI_SYSEVENT_PRIORITY_CHANGE· 350

DRVPLAT· 350

DRVDEBUGMOD_BSP· 350

DRVPLAT/3/DrvDebug· 350

DRVPLAT/3/DrvDebug· 351

DRVPLAT/3/DrvDebug· 351

DRVPLAT/3/DrvDebug· 351

DRVPLAT/3/DrvDebug· 352

DRVPLAT/3/DrvDebug· 352

DRVPLAT/3/DrvDebug· 352

DRVPLAT/3/DrvDebug· 353

DRVPLAT/3/DrvDebug· 353

DRVPLAT/3/DrvDebug· 353

DRVPLAT/3/DrvDebug· 354

DRVPLAT/3/DrvDebug· 354

DRVPLAT/3/DrvDebug· 354

DRVPLAT/3/DrvDebug· 355

DRVDEBUGMOD_DEVM·· 355

DRVPLAT/4/DrvDebug· 355

DRVPLAT/4/DrvDebug· 356

DRVPLAT/2/DrvDebug· 356

DRVPLAT/2/DrvDebug· 357

DRVDEBUGMOD_GOLD·· 357

DRVPLAT/4/DrvDebug· 357

DRVPLAT/4/DrvDebug· 358

DRVPLAT/2/DrvDebug· 358

DRVPLAT/2/DrvDebug· 359

DRVPLAT/2/DrvDebug· 359

DRVPLAT/4/DrvDebug· 360

DRVPLAT/2/DrvDebug· 360

DRVPLAT/2/DrvDebug· 361

DRVPLAT/2/DrvDebug· 361

DRVPLAT/4/DrvDebug· 362

DRVPLAT/4/DrvDebug· 362

DRVPLAT/4/DrvDebug· 362

DRVPLAT/4/DrvDebug· 363

DRVPLAT/4/DrvDebug· 363

DRVPLAT/4/DrvDebug· 363

DRVPLAT/4/DrvDebug· 364

DRVPLAT/4/DrvDebug· 364

DRVPLAT/4/DrvDebug· 365

DRVPLAT/4/DrvDebug· 365

DRVDEBUGMOD_PORT· 366

DRVPLAT/4/DrvDebug· 366

DRVPLAT/4/DrvDebug· 366

DRVDEBUGMOD_RXTX· 367

DRVPLAT/2/DrvDebug· 367

DRVDEBUGMOD_STACK· 367

DRVPLAT/4/DrvDebug· 367

DRVPLAT/4/DrvDebug· 367

DRVPLAT/4/DrvDebug· 368

DRVPLAT/4/DrvDebug· 368

DRVPLAT/4/DrvDebug· 369

DRVPLAT/4/DrvDebug· 370

DRVPLAT/4/DrvDebug· 370

DRVPLAT/4/DrvDebug· 371

DRVPLAT/4/DrvDebug· 371

DRVPLAT/4/DrvDebug· 372

DRVDEBUGMOD_SWFA· 372

DRVPLAT/4/DrvDebug· 372

DRVPLAT/4/DrvDebug· 373

DRVPLAT/4/DrvDebug· 373

DRVPLAT/4/DrvDebug· 374

DRVPLAT/4/DrvDebug· 374

DRVPLAT/4/DrvDebug· 375

DRVPLAT/4/DrvDebug· 375

DRVPLAT/4/DrvDebug· 375

DRVPLAT/4/DrvDebug· 376

DRVPLAT/4/DrvDebug· 376

DRVPLAT/4/DrvDebug· 376

DRVPLAT/4/DrvDebug· 377

DRVPLAT/4/DrvDebug· 377

DRVPLAT/4/DrvDebug· 377

DRVPLAT/4/DrvDebug· 378

DRVDEBUGMOD_SYSM·· 378

DRVPLAT/2/DrvDebug· 378

DRVPLAT/2/DrvDebug· 379

DRVPLAT/2/DrvDebug· 379

DRVPLAT/2/DrvDebug· 379

DRVPLAT/2/DrvDebug· 380

DRVPLAT/2/DrvDebug· 380

DRVPLAT/2/DrvDebug· 381

DRVPLAT/2/DrvDebug· 382

DRVPLAT/2/DrvDebug· 383

DRVPLAT/2/DrvDebug· 384

DRVPLAT/2/DrvDebug· 384

DRVPLAT/2/DrvDebug· 385

DRVPLAT/4/DrvDebug· 385

DRVPLAT/4/DrvDebug· 385

DRVPLAT/2/DrvDebug· 386

DRVPLAT/2/DrvDebug· 386

DRVPLAT/2/DrvDebug· 387

DRVPLAT/2/DrvDebug· 387

DRVPLAT/2/DrvDebug· 388

DRVPLAT/2/DrvDebug· 388

DRVPLAT/2/DrvDebug· 389

DRVPLAT/2/DrvDebug· 389

DRVPLAT/2/DrvDebug· 390

DRVPLAT/2/DrvDebug· 390

DRVPLAT/4/DrvDebug· 390

DRVPLAT/4/DrvDebug· 391

DRVPLAT/4/DrvDebug· 391

DRVPLAT/4/DrvDebug· 391

DRVPLAT/4/DrvDebug· 392

DRVPLAT/4/DrvDebug· 392

DRVPLAT/4/DrvDebug· 392

DRVPLAT/4/DrvDebug· 393

DRVPLAT/4/DrvDebug· 393

DRVPLAT/4/DrvDebug· 393

DRVPLAT/4/DrvDebug· 394

DRVDEBUGMOD_VXLAN· 394

DrvDebug· 394

DrvDebug· 395

EDEV messages· 395

EDEV_ALARM_IN_REMOVED·· 395

EDEV_ALARM_IN_REPORTEDOCCURRED·· 395

EDEV_BOOTROM_UPDATE_FAILED·· 396

EDEV_BOOTROM_UPDATE_SUCCESS· 396

EDEV_FAILOVER_GROUP_STATE_CHANGE· 396

EPON·· 397

EPON_ALARM·· 397

EPON_ALARM·· 397

EPON_ALARM·· 398

EPON_ALARM·· 398

ERPS messages· 398

ERPS_STATE_CHANGED·· 398

ETHOAM messages· 399

ETHOAM_CONNECTION_FAIL_DOWN· 399

ETHOAM_CONNECTION_FAIL_TIMEOUT· 399

ETHOAM_CONNECTION_FAIL_UNSATISF· 399

ETHOAM_CONNECTION_SUCCEED·· 400

ETHOAM_DISABLE· 400

ETHOAM_DISCOVERY_EXIT· 400

ETHOAM_ENABLE· 401

ETHOAM_ENTER_LOOPBACK_CTRLLED·· 401

ETHOAM_ENTER_LOOPBACK_CTRLLING·· 401

ETHOAM_LOCAL_DYING_GASP· 402

ETHOAM_LOCAL_ERROR_FRAME· 402

ETHOAM_LOCAL_ERROR_FRAME_PERIOD·· 402

ETHOAM_LOCAL_ERROR_FRAME_SECOND·· 403

ETHOAM_LOCAL_ERROR_SYMBOL· 403

ETHOAM_LOCAL_LINK_FAULT· 403

ETHOAM_LOOPBACK_EXIT· 404

ETHOAM_LOOPBACK_EXIT_ERROR_STATU· 404

ETHOAM_LOOPBACK_NO_RESOURCE· 404

ETHOAM_LOOPBACK_NOT_SUPPORT· 405

ETHOAM_QUIT_LOOPBACK_CTRLLED·· 405

ETHOAM_QUIT_LOOPBACK_CTRLLING·· 405

ETHOAM_REMOTE_CRITICAL· 406

ETHOAM_REMOTE_DYING_GASP· 406

ETHOAM_REMOTE_ERROR_FRAME· 406

ETHOAM_REMOTE_ERROR_FRAME_PERIOD·· 407

ETHOAM_REMOTE_ERROR_FRAME_SECOND·· 407

ETHOAM_REMOTE_ERROR_SYMBOL· 407

ETHOAM_REMOTE_EXIT· 408

ETHOAM_REMOTE_FAILURE_RECOVER· 408

ETHOAM_REMOTE_LINK_FAULT· 408

ETHOAM_NO_ENOUGH_RESOURCE· 409

ETHOAM_NOT_CONNECTION_TIMEOUT· 409

EVB messages· 409

EVB_AGG_FAILED·· 410

EVB_LICENSE_EXPIRE· 410

EVB_VSI_OFFLINE· 410

EVB_VSI_ONLINE· 411

EVIISIS messages· 411

EVIISIS_LICENSE_EXPIRED·· 411

EVIISIS_LICENSE_EXPIRED_TIME· 411

EVIISIS_LICENSE_UNAVAILABLE· 412

EVIISIS_NBR_CHG·· 412

FCLINK messages· 412

FCLINK_FDISC_REJECT_NORESOURCE· 413

FCLINK_FLOGI_REJECT_NORESOURCE· 413

FCOE messages· 413

FCOE_INTERFACE_NOTSUPPORT_FCOE· 414

FCOE_LAGG_BIND_ACTIVE· 414

FCOE_LAGG_BIND_DEACTIVE· 415

FCZONE messages· 415

FCZONE_DISTRIBUTE_FAILED·· 416

FCZONE_HARDZONE_DISABLED·· 416

FCZONE_HARDZONE_ENABLED·· 417

FCZONE_ISOLATE_ALLNEIGHBOR· 417

FCZONE_ISOLATE_CLEAR_VSAN· 418

FCZONE_ISOLATE_CLEAR_ALLVSAN· 418

FCZONE_ISOLATE_NEIGHBOR· 418

FIB messages· 419

FIB_FILE· 419

FILTER messages· 419

FILTER_EXECUTION_ICMP· 420

FILTER_EXECUTION_ICMPV6· 421

FILTER_IPV4_EXECUTION· 422

FILTER_IPV6_EXECUTION· 423

FIPSNG messages· 423

FCOE_FIPSNG_HARD_RESOURCE_NOENOUGH· 424

FCOE_FIPSNG_HARD_RESOURCE_RESTORE· 424

FS messages· 424

FS_UNFORMATTED_PARTITION· 425

FTPD messages· 425

FTP_ACL_DENY· 425

FTPD_REACH_SESSION_LIMIT· 426

FTPD_AUTHOR_FAILED·· 426

gRPC messages· 426

GRPC_LOGIN· 427

GRPC_LOGIN_FAILED·· 427

GRPC_LOGOUT· 427

GRPC_SERVER_FAILED·· 428

GRPC_SUBSCRIBE_EVENT_FAILED·· 428

GRPC_RECEIVE_SUBSCRIPTION· 428

HA messages· 428

HA_BATCHBACKUP_FINISHED·· 429

HA_BATCHBACKUP_STARTED·· 429

HA_STANDBY_NOT_READY· 429

HA_STANDBY_TO_MASTER· 430

HQOS messages· 430

HQOS_DP_SET_FAIL· 430

HQOS_FP_SET_FAIL· 431

HQOS_POLICY_APPLY_FAIL· 431

HQOS_POLICY_APPLY_FAIL· 432

HTTPD messages· 432

HTTPD_CONNECT· 432

HTTPD_CONNECT_TIMEOUT· 433

HTTPD_DISCONNECT· 433

HTTPD_FAIL_FOR_ACL· 433

HTTPD_FAIL_FOR_ACP· 434

HTTPD_REACH_CONNECT_LIMIT· 434

IFNET messages· 434

IF_BUFFER_CONGESTION_OCCURRENCE· 435

IF_BUFFER_CONGESTION_CLEAR· 435

IF_JUMBOFRAME_WARN· 436

INTERFACE_NOTSUPPRESSED·· 436

INTERFACE_SUPPRESSED·· 436

LINK_UPDOWN· 437

PHY_UPDOWN· 437

PROTOCOL_UPDOWN· 437

TUNNEL_LINK_UPDOWN· 438

TUNNEL_PHY_UPDOWN· 438

VLAN_MODE_CHANGE· 438

IKE messages· 439

IKE_P1_SA_ESTABLISH_FAIL· 439

IKE_P2_SA_ESTABLISH_FAIL· 440

IKE_P2_SA_TERMINATE· 440

IKE_VERIFY_CERT_FAIL· 441

IPADDR messages· 442

IPADDR_HA_EVENT_ERROR· 443

IPADDR_HA_STOP_EVENT· 444

IPFW·· 444

IPFW_FAILURE· 444

IPSEC messages· 444

IPSEC_FAILED_ADD_FLOW_TABLE· 445

IPSEC_PACKET_DISCARDED·· 445

IPSEC_SA_ESTABLISH· 446

IPSEC_SA_ESTABLISH_FAIL· 446

IPSEC_SA_INITINATION· 447

IPSEC_SA_TERMINATE· 447

IPSG messages· 447

IPSG_ADDENTRY_ERROR· 448

IPSG_DELENTRY_ERROR· 449

IPSG_ADDEXCLUDEDVLAN_ERROR· 450

IPSG_DELEXCLUDEDVLAN_ERROR· 451

IRDP messages· 451

IRDP_EXCEED_ADVADDR_LIMIT· 451

IRF· 452

IRF_LINK_BLOCK· 452

IRF_LINK_DOWN· 452

IRF_LINK_UP· 452

IRF_MEMBERID_CONFLICT· 453

IRF_MERGE· 453

IRF_MERGE_NEED_REBOOT· 453

IRF_MERGE_NOT_NEED_REBOOT· 454

ISIS messages· 454

ISIS_LSP_CONFLICT· 454

ISIS_MEM_ALERT· 455

ISIS_NBR_CHG·· 455

ISSU messages· 455

ISSU_LOAD_FAILED·· 456

ISSU_LOAD_SUCCESS· 456

ISSU_PROCESSWITCHOVER· 456

ISSU_ROLLBACKCHECKNORMAL· 457

L2PT messages· 457

L2PT_SET_MULTIMAC_FAILED·· 457

L2PT_CREATE_TUNNELGROUP_FAILED·· 457

L2PT_ADD_GROUPMEMBER_FAILED·· 458

L2PT_ENABLE_DROP_FAILED·· 458

L2TP messages· 458

L2TPV2_TUNNEL_EXCEED_LIMIT· 459

L2TPV2_SESSION_EXCEED_LIMIT· 459

L2VPN messages· 459

L2VPN_BGPVC_CONFLICT_LOCAL· 460

L2VPN_BGPVC_CONFLICT_REMOTE· 460

L2VPN_HARD_RESOURCE_NOENOUGH· 461

L2VPN_HARD_RESOURCE_RESTORE· 461

L2VPN_LABEL_DUPLICATE· 461

LAGG messages· 462

LAGG_ACTIVE· 462

LAGG_AUTO_AGGREGATION· 462

LAGG_INACTIVE_AICFG·· 463

LAGG_INACTIVE_BFD·· 463

LAGG_INACTIVE_CONFIGURATION· 464

LAGG_INACTIVE_DUPLEX· 464

LAGG_INACTIVE_HARDWAREVALUE· 465

LAGG_INACTIVE_LOWER_LIMIT· 465

LAGG_INACTIVE_PARTNER· 465

LAGG_INACTIVE_PHYSTATE· 466

LAGG_INACTIVE_RESOURCE_INSUFICIE· 466

LAGG_INACTIVE_SPEED·· 466

LAGG_INACTIVE_UPPER_LIMIT· 467

LDP messages· 467

LDP_MPLSLSRID_CHG·· 467

LDP_SESSION_CHG·· 468

LDP_SESSION_GR· 469

LDP_SESSION_SP· 469

License messages· 470

LIC_INIT· 470

LLDP messages· 470

LLDP_CREATE_NEIGHBOR· 471

LLDP_DELETE_NEIGHBOR· 471

LLDP_LESS_THAN_NEIGHBOR_LIMIT· 472

LLDP_NEIGHBOR_AGE_OUT· 472

LLDP_NEIGHBOR_PROTECTION_BLOCK· 473

LLDP_NEIGHBOR_PROTECTION_DOWN· 473

LLDP_NEIGHBOR_PROTECTION_UNBLOCK· 474

LLDP_NEIGHBOR_PROTECTION_UP· 474

LLDP_PVID_INCONSISTENT· 474

LLDP_PVID_INCONSISTENT· 475

LLDP_REACH_NEIGHBOR_LIMIT· 475

LOAD messages· 475

BOARD_LOADING·· 476

LOAD_FAILED·· 476

LOAD_FINISHED·· 476

LOGIN messages· 477

LOGIN_FAILED·· 477

LOGIN_ INVALID_USERNAME_PWD·· 477

LPDT messages· 477

LPDT_LOOPED·· 478

LPDT_RECOVERED·· 478

LPDT_VLAN_LOOPED·· 478

LPDT_VLAN_RECOVERED·· 479

LS messages· 479

LS_ADD_USER_TO_GROUP· 479

LS_AUTHEN_FAILURE· 480

LS_AUTHEN_SUCCESS· 480

LS_DEL_USER_FROM_GROUP· 480

LS_DELETE_PASSWORD_FAIL· 481

LS_PWD_ADDBLACKLIST· 481

LS_PWD_CHGPWD_FOR_AGEDOUT· 481

LS_PWD_CHGPWD_FOR_AGEOUT· 482

LS_PWD_CHGPWD_FOR_COMPOSITION· 482

LS_PWD_CHGPWD_FOR_FIRSTLOGIN· 482

LS_PWD_CHGPWD_FOR_LENGTH· 483

LS_PWD_FAILED2WRITEPASS2FILE· 483

LS_PWD_MODIFY_FAIL· 483

LS_PWD_MODIFY_SUCCESS· 484

LS_REAUTHEN_FAILURE· 484

LS_UPDATE_PASSWORD_FAIL· 484

LS_USER_CANCEL· 485

LS_USER_PASSWORD_EXPIRE· 485

LS_USER_ROLE_CHANGE· 485

LSPV messages· 485

LSPV_PING_STATIS_INFO·· 486

MAC messages· 486

MAC_DRIVER_ADD_ENTRY· 486

MAC_TABLE_FULL_GLOBAL· 487

MAC_TABLE_FULL_PORT· 487

MAC_TABLE_FULL_VLAN· 487

MAC_VLAN_LEARNLIMIT_NORESOURCE· 488

MAC_VLAN_LEARNLIMIT_NOTSUPPORT· 488

MACA messages· 488

MACA_ENABLE_NOT_EFFECTIVE· 488

MACA_LOGIN_FAILURE· 489

MACA_LOGIN_SUCC· 490

MACA_LOGIN_SUCC (in open mode) 490

MACA_LOGOFF· 491

MACA_LOGOFF (in open mode) 491

MACSEC messages· 492

MACSEC_MKA_KEEPALIVE_TIMEOUT· 492

MACSEC_MKA_PRINCIPAL_ACTOR· 492

MACSEC_MKA_SAK_REFRESH· 493

MACSEC_MKA_SESSION_REAUTH· 493

MACSEC_MKA_SESSION_SECURED·· 494

MACSEC_MKA_SESSION_START· 494

MACSEC_MKA_SESSION_STOP· 495

MACSEC_MKA_SESSION_UNSECURED·· 495

MBFD messages· 496

MBFD_TRACEROUTE_FAILURE· 496

MBUF messages· 496

MBUF_DATA_BLOCK_CREATE_FAIL· 497

MDC messages· 497

MDC_CREATE_ERR· 498

MDC_CREATE· 498

MDC_DELETE· 498

MDC_KERNEL_EVENT_TOOLONG·· 499

MDC_LICENSE_EXPIRE· 499

MDC_NO_FORMAL_LICENSE· 499

MDC_NO_LICENSE_EXIT· 500

MDC_OFFLINE· 500

MDC_ONLINE· 500

MDC_STATE_CHANGE· 501

MFIB messages· 501

MFIB_MEM_ALERT· 501

MGROUP messages· 501

MGROUP_APPLY_SAMPLER_FAIL· 502

MGROUP_RESTORE_CPUCFG_FAIL· 502

MGROUP_RESTORE_GROUP_FAIL· 503

MGROUP_RESTORE_IFCFG_FAIL· 503

MGROUP_SYNC_CFG_FAIL· 504

MPLS messages· 504

MPLS_HARD_RESOURCE_NOENOUGH· 504

MPLS_HARD_RESOURCE_RESTORE· 505

MTLK messages· 505

MTLK_UPLINK_STATUS_CHANGE· 505

NAT messages· 505

NAT_ADDR_BIND_CONFLICT· 506

NAT_FAILED_ADD_FLOW_RULE· 506

NAT_FAILED_ADD_FLOW_TABLE· 507

NAT_FLOW·· 508

NAT_SERVICE_CARD_RECOVER_FAILURE· 509

NAT_SERVER_INVALID·· 509

ND messages· 510

ND_COMMONPROXY_ENABLE_FAILED·· 510

ND_CONFLICT· 510

ND_DUPADDR· 511

ND_HOST_IP_CONFLICT· 511

ND_LOCALPROXY_ENABLE_FAILED·· 511

ND_MAC_CHECK· 512

ND_RAGUARD_DROP· 512

ND_SET_PORT_TRUST_NORESOURCE· 512

ND_SET_VLAN_REDIRECT_NORESOURCE· 513

NETCONF messages· 513

CLI 513

EDIT-CONFIG·· 514

THREAD·· 514

NQA messages· 515

NQA_LOG_UNREACHABLE· 515

NTP messages· 515

NTP_CLOCK_CHANGE· 515

NTP_LEAP_CHANGE· 516

NTP_SOURCE_CHANGE· 516

NTP_SOURCE_LOST· 517

NTP_STRATUM_CHANGE· 517

OBJP messages· 517

OBJP_ACCELERATE_NO_RES· 518

OBJP_ACCELERATE_NOT_SUPPORT· 518

OBJP_ACCELERATE_UNK_ERR· 518

OFP messages· 519

OFP_ACTIVE· 519

OFP_ACTIVE_FAILED·· 519

OFP_CONNECT· 519

OFP_FAIL_OPEN· 520

OFP_FLOW_ADD·· 520

OFP_FLOW_ADD_ARP_FAILED·· 520

OFP_FLOW_ADD_DUP· 521

OFP_FLOW_ADD_FAILED·· 521

OFP_FLOW_ADD_FAILED·· 522

OFP_FLOW_ADD_TABLE_MISS· 522

OFP_FLOW_ADD_TABLE_MISS_FAILED·· 523

OFP_FLOW_DEL· 523

OFP_FLOW_DEL_L2VPN_DISABLE· 524

OFP_FLOW_DEL_TABLE_MISS· 524

OFP_FLOW_DEL_TABLE_MISS_FAILED·· 525

OFP_FLOW_DEL_VXLAN_DEL· 525

OFP_FLOW_MOD·· 526

OFP_FLOW_MOD_FAILED·· 526

OFP_FLOW_MOD_TABLE_MISS· 527

OFP_FLOW_MOD_TABLE_MISS_FAILED·· 527

OFP_FLOW_RMV_GROUP· 528

OFP_FLOW_RMV_HARDTIME· 528

OFP_FLOW_RMV_IDLETIME· 528

OFP_FLOW_RMV_METER· 529

OFP_FLOW_UPDATE_FAILED·· 529

OFP_GROUP_ADD·· 530

OFP_GROUP_ADD_FAILED·· 530

OFP_GROUP_DEL· 531

OFP_GROUP_MOD·· 531

OFP_GROUP_MOD_FAILED·· 532

OFP_METER_ADD·· 532

OFP_METER_ADD_FAILED·· 532

OFP_METER_DEL· 533

OFP_METER_MOD·· 533

OFP_METER_MOD_FAILED·· 534

OFP_MISS_RMV_GROUP· 534

OFP_MISS_RMV_HARDTIME· 534

OFP_MISS_RMV_IDLETIME· 535

OFP_MISS_RMV_METER· 535

OFP_RADARDETECTION· 535

PORT_MOD·· 536

OPENSRC (FreeRADIUS) messages· 537

HUP event 537

Process restart event 538

Process start event 538

User authentication· 539

OPTMOD messages· 541

BIAS_HIGH· 542

BIAS_LOW·· 542

BIAS_NORMAL· 542

CFG_ERR· 543

CHKSUM_ERR· 543

FIBER_SFP MODULE_INVALID·· 543

FIBER_SFPMODULE_NOWINVALID·· 544

IO_ERR· 544

MOD_ALM_OFF· 544

MOD_ALM_ON· 545

MODULE_IN· 545

MODULE_OUT· 545

PHONY_MODULE· 546

RX_ALM_OFF· 546

RX_ALM_ON· 546

RX_POW_HIGH· 547

RX_POW_LOW·· 547

RX_POW_NORMAL· 547

TEMP_HIGH· 548

TEMP_LOW·· 548

TEMP_NORMAL· 548

TX_ALM_OFF· 549

TX_ALM_ON· 549

TX_POW_HIGH· 549

TX_POW_LOW·· 550

TX_POW_NORMAL· 550

TYPE_ERR· 550

VOLT_HIGH· 551

VOLT_LOW·· 551

VOLT_NORMAL· 551

OSPF messages· 552

OSPF_DUP_RTRID_NBR· 552

OSPF_IP_CONFLICT_INTRA· 552

OSPF_LAST_NBR_DOWN· 553

OSPF_MEM_ALERT· 553

OSPF_NBR_CHG·· 554

OSPF_RT_LMT· 554

OSPF_RTRID_CHG·· 554

OSPF_RTRID_CONFLICT_INTER· 555

OSPF_RTRID_CONFLICT_INTRA· 555

OSPF_VLINKID_CHG·· 555

OSPFV3 messages· 556

OSPFV3_LAST_NBR_DOWN· 556

OSPFV3_MEM_ALERT· 556

OSPFV3_NBR_CHG·· 557

OSPFV3_RT_LMT· 557

PBB messages· 557

PBB_JOINAGG_WARNING·· 558

PBR messages· 558

PBR_HARDWARE_ERROR· 558

PCE messages· 558

PCE_PCEP_SESSION_CHG·· 559

PEX messages (IRF 3) 559

PEX_ASSOCIATEID_MISMATCHING·· 560

PEX_CONFIG_ERROR· 560

PEX_CONNECTION_ERROR· 561

PEX_FORBID_STACK· 561

PEX_LINK_BLOCK· 562

PEX_LINK_DOWN· 563

PEX_LINK_FORWARD·· 563

PEX_REG_JOININ· 564

PEX_REG_LEAVE· 564

PEX_REG_REQUEST· 565

PEX_STACKCONNECTION_ERROR· 565

PEX messages (IRF 3.1) 565

PEX_AUTOCONFIG_BAGG_ASSIGNMEMBER· 566

PEX_AUTOCONFIG_BAGG_CREATE· 566

PEX_AUTOCONFIG_BAGG_NORESOURCE· 566

PEX_AUTOCONFIG_BAGG_REMOVEMEMBER· 567

PEX_AUTOCONFIG_CAPABILITY_ENABLE· 567

PEX_AUTOCONFIG_CASCADELIMIT· 568

PEX_AUTOCONFIG_CONNECTION_ERROR· 568

PEX_AUTOCONFIG_DIFFGROUPNUMBER· 568

PEX_AUTOCONFIG_DYNAMICBAGG_STP· 569

PEX_AUTOCONFIG_GROUP_CREATE· 569

PEX_AUTOCONFIG_NONUMBERRESOURCE· 569

PEX_AUTOCONFIG_NOT_CASCADEPORT· 570

PEX_AUTOCONFIG_NUMBER_ASSIGN· 570

PEX_LLDP_DISCOVER· 571

PEX_MEMBERID_EXCEED·· 571

PEX_PECSP_OPEN_RCVD·· 571

PEX_PECSP_OPEN_SEND·· 572

PEX_PECSP_TIMEOUT· 572

PFILTER messages· 572

PFILTER_GLB_IPV4_DACT_NO_RES· 573

PFILTER_GLB_IPV4_DACT_UNK_ERR· 573

PFILTER_GLB_IPV6_DACT_NO_RES· 574

PFILTER_GLB_IPV6_DACT_UNK_ERR· 574

PFILTER_GLB_MAC_DACT_NO_RES· 575

PFILTER_GLB_MAC_DACT_UNK_ERR· 575

PFILTER_GLB_NO_RES· 576

PFILTER_GLB_NOT_SUPPORT· 576

PFILTER_GLB_ RES_CONFLICT· 577

PFILTER_GLB_UNK_ERR· 577

PFILTER_IF_IPV4_DACT_NO_RES· 578

PFILTER_IF_IPV4_DACT_UNK_ERR· 578

PFILTER_IF_IPV6_DACT_NO_RES· 579

PFILTER_IF_IPV6_DACT_UNK_ERR· 579

PFILTER_IF_MAC_DACT_NO_RES· 580

PFILTER_IF_MAC_DACT_UNK_ERR· 580

PFILTER_IF_NO_RES· 581

PFILTER_IF_NOT_SUPPORT· 581

PFILTER_IF_RES_CONFLICT· 582

PFILTER_IF_UNK_ERR· 582

PFILTER_IPV4_FLOW_INFO·· 583

PFILTER_IPV4_FLOW_STATIS· 583

PFILTER_IPV6_FLOW_INFO·· 584

PFILTER_IPV6_FLOW_STATIS· 584

PFILTER_IPV6_STATIS_INFO·· 585

PFILTER_MAC_FLOW_INFO·· 585

PFILTER_STATIS_INFO·· 586

PFILTER_VLAN_IPV4_DACT_NO_RES· 586

PFILTER_VLAN_IPV4_DACT_UNK_ERR· 587

PFILTER_VLAN_IPV6_DACT_NO_RES· 587

PFILTER_VLAN_IPV6_DACT_UNK_ERR· 588

PFILTER_VLAN_MAC_DACT_NO_RES· 588

PFILTER_VLAN_MAC_DACT_UNK_ERR· 589

PFILTER_VLAN_NO_RES· 589

PFILTER_VLAN_NOT_SUPPORT· 590

PFILTER_VLAN_RES_CONFLICT· 590

PFILTER_VLAN_UNK_ERR· 591

PIM messages· 591

PIM_NBR_DOWN· 591

PIM_NBR_UP· 592

PING messages· 592

PING_STATISTICS· 592

PING_VPN_STATISTICS· 593

PKG messages· 593

PKG_BOOTLOADER_FILE_FAILED·· 593

PKG_BOOTLOADER_FILE_SUCCESS· 594

PKG_INSTALL_ACTIVATE_FAILED·· 594

PKG_INSTALL_ACTIVATE_SUCCESS· 594

PKI messages· 594

GET_CERT_FROM_CA_SERVER_FAIL· 595

IMPORT_CERT_FAIL· 596

REQUEST_CERT_FAIL· 597

REQUEST_CERT_SUCCESS· 598

RETRIEVE_CRL_FAIL· 598

VALIDATE_CERT_FAIL· 599

PKT2CPU messages· 600

PKT2CPU_NO_RESOURCE· 601

PKTCPT· 601

PKTCPT_AP_OFFLINE· 601

PKTCPT_AREADY_EXIT· 602

PKTCPT_CONN_FAIL· 602

PKTCPT_INVALID_FILTER· 603

PKTCPT_LOGIN_DENIED·· 603

PKTCPT_MEMORY_ALERT· 603

PKTCPT_OPEN_FAIL· 604

PKTCPT_OPERATION_TIMEOUT· 604

PKTCPT_SERVICE_FAIL· 605

PKTCPT_UNKNOWN_ERROR· 605

PKTCPT_UPLOAD_ERROR· 605

PKTCPT_WRITE_FAIL· 606

Portal messages· 606

PORTAL_RULE_FAILED·· 606

PORTSEC messages· 607

PORTSEC_ACL_FAILURE· 607

PORTSEC_CAR_FAILURE· 607

PORTSEC_CREATEAC_FAILURE· 608

PORTSEC_LEARNED_MACADDR· 608

PORTSEC_NTK_NOT_EFFECTIVE· 609

PORTSEC_PORTMODE_NOT_EFFECTIVE· 609

PORTSEC_PROFILE_FAILURE· 610

PORTSEC_URL_FAILURE· 610

PORTSEC_VIOLATION· 611

PPP messages· 611

IPPOOL_ADDRESS_EXHAUSTED·· 611

PPP_USER_LOGON_SUCCESS· 612

PPP_USER_LOGON_FAILED·· 612

PPP_USER_LOGOFF· 613

PWDCTL messages· 614

ADDBLACKLIST· 614

CHANGEPASSWORD·· 614

FAILEDTOWRITEPWD·· 615

FAILEDTOOPENFILE· 615

NOENOUGHSPACE· 615

QOS messages· 615

MIRROR_SYNC_CFG_FAIL· 616

QOS_CAR_APPLYUSER_FAIL· 616

QOS_CBWFQ_REMOVED·· 617

QOS_GTS_APPLYUSER_FAIL· 617

QOS_NOT_ENOUGH_BANDWIDTH· 618

QOS_NOT_ENOUGH_NNIBANDWIDTH· 618

QOS_POLICY_APPLYCOPP_CBFAIL· 619

QOS_POLICY_APPLYCOPP_FAIL· 619

QOS_POLICY_APPLYGLOBAL_CBFAIL· 620

QOS_POLICY_APPLYGLOBAL_FAIL· 620

QOS_POLICY_APPLYIF_CBFAIL· 621

QOS_POLICY_APPLYIF_FAIL· 621

QOS_POLICY_APPLYUSER_FAIL· 622

QOS_POLICY_APPLYVLAN_CBFAIL· 622

QOS_POLICY_APPLYVLAN_FAIL· 623

QOS_QMPROFILE_APPLYUSER_FAIL· 623

QOS_QMPROFILE_MODIFYQUEUE_FAIL· 624

QOS_UNI_RESTORE_FAIL· 624

WRED_TABLE_CFG_FAIL· 624

RADIUS messages· 625

RADIUS_AUTH_FAILURE· 625

RADIUS_AUTH_SUCCESS· 625

RADIUS_DELETE_HOST_FAIL· 625

RDDC messages· 626

RDDC_ACTIVENODE_CHANGE· 626

RESMON·· 626

RESMON_MINOR· 627

RESMON_MINOR_RECOVERY· 627

RESMON_SEVERE· 628

RESMON_SEVERE_RECOVERY· 628

RESMON_USEDUP· 629

RESMON_USEDUP_RECOVERY· 629

RIP messages· 629

RIP_MEM_ALERT· 630

RIP_RT_LMT· 630

RIPNG messages· 630

RIPNG_MEM_ALERT· 630

RIPNG_RT_LMT· 631

RM messages· 631

RM_ACRT_REACH_LIMIT· 631

RM_ACRT_REACH_THRESVALUE· 632

RM_THRESHLD_VALUE_REACH· 632

RM_TOTAL_THRESHLD_VALUE_REACH· 632

RPR messages· 633

RPR_EXCEED_MAX_SEC_MAC· 633

RPR_EXCEED_MAX_SEC_MAC_OVER· 633

RPR_EXCEED_MAX_STATION· 634

RPR_EXCEED_MAX_STATION_OVER· 634

RPR_EXCEED_RESERVED_RATE· 634

RPR_EXCEED_RESERVED_RATE_OVER· 635

RPR_IP_DUPLICATE· 635

RPR_IP_DUPLICATE_OVER· 635

RPR_JUMBO_INCONSISTENT· 636

RPR_JUMBO_INCONSISTENT_OVER· 636

RPR_MISCABLING·· 636

RPR_MISCABLING_OVER· 637

RPR_PROTECTION_INCONSISTENT· 637

RPR_PROTECTION_INCONSISTENT_OVER· 637

RPR_SEC_MAC_DUPLICATE· 638

RPR_SEC_MAC_DUPLICATE_OVER· 638

RPR_TOPOLOGY_INCONSISTENT· 638

RPR_TOPOLOGY_INCONSISTENT_OVER· 639

RPR_TOPOLOGY_INSTABILITY· 639

RPR_TOPOLOGY_INSTABILITY_OVER· 639

RPR_TOPOLOGY_INVALID·· 640

RPR_TOPOLOGY_INVALID_OVER· 640

RRPP messages· 640

RRPP_RING_FAIL· 640

RRPP_RING_RESTORE· 641

RTM messages· 641

RTM_TCL_NOT_EXIST· 641

RTM_TCL_MODIFY· 641

RTM_TCL_LOAD_FAILED·· 642

SCM messages· 642

PROCESS_ABNORMAL· 642

PROCESS_ACTIVEFAILED·· 643

SCM_ABNORMAL_REBOOT· 643

SCM_ABNORMAL_REBOOTMDC· 644

SCM_ABORT_RESTORE· 644

SCM_INSMOD_ADDON_TOOLONG·· 645

SCM_KERNEL_INIT_TOOLONG·· 645

SCM_PROCESS_STARTING_TOOLONG·· 646

SCM_PROCESS_STILL_STARTING·· 646

SCM_SKIP_PROCESS· 647

SCM_SKIP_PROCESS· 647

SCRLSP messages· 647

SCRLSP_LABEL_DUPLICATE· 648

SESSION messages· 648

SESSION_IPV4_FLOW·· 649

SESSION_IPV6_FLOW·· 650

SFLOW messages· 651

SFLOW_HARDWARE_ERROR· 651

SHELL messages· 651

SHELL_CMD·· 651

SHELL_CMD_CONFIRM·· 652

SHELL_CMD_EXECUTEFAIL· 652

SHELL_CMD_INPUT· 652

SHELL_CMD_INPUT_TIMEOUT· 653

SHELL_CMD_MATCHFAIL· 653

SHELL_CMDDENY· 653

SHELL_CMDFAIL· 654

SHELL_CRITICAL_CMDFAIL· 654

SHELL_LOGIN· 654

SHELL_LOGOUT· 655

SLSP messages· 655

SLSP_LABEL_DUPLICATE· 655

SMLK messages· 655

SMLK_LINK_SWITCH· 656

SNMP messages· 656

SNMP_ACL_RESTRICTION· 656

SNMP_AUTHENTICATION_FAILURE· 656

SNMP_GET· 657

SNMP_NOTIFY· 657

SNMP_SET· 658

SNMP_USM_NOTINTIMEWINDOW·· 658

SSHC messages· 658

SSHC_ALGORITHM_MISMATCH· 659

SSHC_AUTH_PASSWORD_FAIL· 659

SSHC_AUTH_PUBLICKEY_FAIL· 659

SSHC_CERT_VERIFY_FAIL· 660

SSHC_CONNECT_FAIL· 661

SSHC_DECRYPT_FAIL· 661

SSHC_DISCONNECT· 662

SSHC_ENCRYPT_FAIL· 662

SSHC_HOST_NAME_ERROR· 662

SSHC_KEY_EXCHANGE_FAIL· 663

SSHC_MAC_ERROR· 663

SSHC_PUBLICKEY_NOT_EXIST· 663

SSHC_VERSION_MISMATCH· 664

SSHS messages· 664

SSHS_ACL_DENY· 664

SSHS_ALGORITHM_MISMATCH· 664

SSHS_AUTH_EXCEED_RETRY_TIMES· 665

SSHS_AUTH_FAIL· 665

SSHS_AUTH_KBDINT_FAIL· 665

SSHS_AUTH_PWD_FAIL· 666

SSHS_AUTH_TIMEOUT· 666

SSHS_AUTH_SUCCESS· 666

SSHS_AUTHOR_FAIL· 667

SSHS_CERT_VERIFY_FAIL· 668

SSHS_CONNECT· 669

SSHS_DECRYPT_FAIL· 669

SSHS_DISCONNECT· 670

SSHS_ENCRYPT_FAIL· 670

SSHS_LOG·· 670

SSHS_MAC_ERROR· 671

SSHS_REACH_SESSION_LIMIT· 671

SSHS_REACH_USER_LIMIT· 671

SSHS_SCP_OPER· 672

SSHS_SFTP_OPER· 672

SSHS_SRV_UNAVAILABLE· 673

SSHS_VERSION_MISMATCH· 673

STAMGR messages· 673

STAMGR_ADD_FAILVLAN· 673

STAMGR_ADDBAC_INFO·· 674

STAMGR_ADDSTA_INFO·· 674

STAMGR_AUTHORACL_FAILURE· 674

STAMGR_AUTHORUSERPROFILE_FAILURE· 675

STAMGR_CLIENT_OFFLINE· 675

STAMGR_CLIENT_ONLINE· 675

STAMGR_DELBAC_INFO·· 676

STAMGR_DELSTA_INFO·· 676

STAMGR_DOT1X_LOGIN_FAILURE· 676

STAMGR_DOT1X_LOGIN_SUCC· 677

STAMGR_DOT1X_LOGOFF· 677

STAMGR_MACA_LOGIN_FAILURE· 678

STAMGR_MACA_LOGIN_SUCC· 678

STAMGR_MACA_LOGOFF· 679

STAMGR_STAIPCHANGE_INFO·· 679

STAMGR_TRIGGER_IP· 680

STM messages· 680

STM_AUTO_UPDATE_FAILED·· 681

STM_AUTO_UPDATE_FINISHED·· 682

STM_AUTO_UPDATING·· 682

STM_LINK_DOWN· 683

STM_LINK_TIMEOUT· 683

STM_LINK_UP· 683

STM_MERGE· 684

STM_MERGE_NEED_REBOOT· 684

STM_MERGE_NOT_NEED_REBOOT· 684

STM_SAMEMAC· 685

STM_SOMER_CHECK· 685

STP messages· 685

STP_BPDU_PROTECTION· 686

STP_BPDU_RECEIVE_EXPIRY· 686

STP_CONSISTENCY_RESTORATION· 686

STP_DETECTED_TC· 687

STP_DISABLE· 687

STP_DISCARDING·· 687

STP_DISPUTE· 688

STP_ENABLE· 688

STP_FORWARDING·· 688

STP_LOOP_PROTECTION· 689

STP_LOOPBACK_PROTECTION· 689

STP_NOT_ROOT· 689

STP_NOTIFIED_TC· 690

STP_PORT_TYPE_INCONSISTENCY· 690

STP_PVID_INCONSISTENCY· 690

STP_PVST_BPDU_PROTECTION· 691

STP_ROOT_PROTECTION· 691

SYSLOG messages· 691

SYSLOG_LOGFILE_FULL· 692

SYSLOG_NO_SPACE· 692

SYSLOG_RESTART· 692

SYSLOG_RTM_EVENT_BUFFER_FULL· 693

TACACS messages· 693

TACACS_AUTH_FAILURE· 693

TACACS_AUTH_SUCCESS· 694

TACACS_DELETE_HOST_FAIL· 694

TELNETD messages· 694

TELNETD_ACL_DENY· 694

TELNETD_REACH_SESSION_LIMIT· 695

TRILL messages· 695

TRILL_DUP_SYSTEMID·· 695

TRILL_INTF_CAPABILITY· 696

TRILL_LICENSE_EXPIRED·· 696

TRILL_LICENSE_EXPIRED_TIME· 696

TRILL_LICENSE_UNAVAILABLE· 697

TRILL_MEM_ALERT· 697

TRILL_NBR_CHG·· 697

VCF messages· 698

VCF_AGGR_CREAT· 698

VCF_AGGR_DELETE· 698

VCF_AGGR_FAILED·· 699

VCF_AUTO_ANALYZE_USERDEF· 699

VCF_AUTO_NO_USERDEF· 699

VCF_AUTO_START· 700

VCF_AUTO_STATIC_CMD·· 700

VCF_BGP· 700

VCF_DOWN_LINK· 701

VCF_GET_IMAGE· 701

VCF_GET_TEMPLATE· 702

VCF_INSTALL_IMAGE· 702

VCF_IRF_FINISH· 702

VCF_IRF_FOUND·· 703

VCF_IRF_REBOOT· 703

VCF_IRF_START· 704

VCF_LOOPBACK_START· 704

VCF_LOOPBACK_START_FAILED·· 705

VCF_LOOPBACK_ALLOC· 705

VCF_LOOPBACK_NO_FREE_IP· 706

VCF_LOOPBACK_RECLAIM·· 706

VCF_REBOOT· 706

VCF_SKIP_INSTALL· 707

VCF_STATIC_CMD_ERROR· 707

VCF_UP_LINK· 707

VLAN messages· 708

VLAN_CREATEVLAN_NO_ENOUGH_RESOUR· 708

VLAN_FAILED·· 708

VLAN_VLANMAPPING_FAILED·· 709

VLAN_VLANTRANSPARENT_FAILED·· 709

VRRP messages· 709

VRRP_STATUS_CHANGE· 710

VRRP_VF_STATUS_CHANGE· 711

VRRP_VMAC_INEFFECTIVE· 711

VSRP messages· 711

VSRP_BIND_FAILED·· 712

VXLAN messages· 712

VXLAN_LICENSE_UNAVAILABLE· 712

WIPS messages· 712

APFLOOD·· 713

AP_CHANNEL_CHANGE· 713

ASSOCIATEOVERFLOW·· 713

HONEYPOT· 714

HTGREENMODE· 714

MAN_IN_MIDDLE· 714

WIPS_DOS· 715

WIPS_FLOOD·· 715

WIPS_MALF· 716

WIPS_SPOOF· 716

WIPS_WEAKIV· 717

WIRELESSBRIDGE· 717

 


Introduction

This document includes all system messages for Comware 7 software. It is intended for system administrators who are responsible for managing Comware 7 systems.

This document assumes that the readers are familiar with data communications technologies and H3C networking products.

System log message format

By default, the system log messages use one of the following formats depending on the output destination:

·           Log host:

<PRI>TIMESTAMP Sysname %%vendorMODULE/severity/MNEMONIC: location; CONTENT

·           Destinations except for the log host:

Prefix TIMESTAMP Sysname MODULE/severity/MNEMONIC: CONTENT

Table 1 System log message elements

Element

Description

<PRI>

Priority identifier. It is calculated by using the following formula:

Priority identifier=facilityx8+severity

Where:

·                        Facility is specified by using the info-center loghost command. A log host uses this parameter to identify log sources and filter log messages.

·                        Severity represents the importance of the message. For more information about severity levels, see Table 2.

Prefix

Message type identifier. This element is contained in the system log messages sent to non-log host destinations.

The element uses the following symbols to indicate message severity:

·                        Percentage sign (%)—Informational and higher levels.

·                        Asterisk (*)—Debug level.

TIMESTAMP

Date and time when the event occurred.

The following are commands for configuring the timestamp format:

·                        Log host—Use the info-center timestamp loghost command.

·                        Non-log host destinationsUse the info-center timestamp command.

Sysname

Name or IP address of the device that generated the message.

%%vendor

Manufacturer flag. This element is %%10 for H3C.

This element is only available in messages sent to the log host.

MODULE

Name of the module that produced the message.

severity

Severity level of the message. (For more information about severity levels, see Table 2.)

MNEMONIC

Text string that uniquely identifies the system message. The maximum length is 32 characters.

location

Optional. This element presents location information for the message in the following format:

-attribute1=x-attribute2=y…-attributeN=z

This element is separated from the message description by using a semicolon (;).

CONTENT

Text string that contains detailed information about the event or error.

For variable fields in this element, this document uses the representations in Table 3.

 

System log messages are classified into eight severity levels from 0 to 7. The lower the number, the higher the severity, as shown in Table 2.

Table 2 System log message severity levels

Level

Severity

Description

0

Emergency

The system is unusable. For example, the system authorization has expired.

1

Alert

Action must be taken immediately. For example, traffic on an interface exceeds the upper limit.

2

Critical

Critical condition. For example, the device temperature exceeds the upper limit, the power module fails, or the fan tray fails.

3

Error

Error condition. For example, the link state changes or a storage card is unplugged.

4

Warning

Warning condition. For example, an interface is disconnected, or the memory resources are used up.

5

Notification

Normal but significant condition. For example, a terminal logs in to the device, or the device reboots.

6

Informational

Informational message. For example, a command or a ping operation is executed.

7

Debug

Debugging message.

 

For variable fields in the message text, this document uses the representations in Table 3. The values are case insensitive, even though the representations are uppercase letters.

Table 3 Variable field representations

Representation

Information type

INT16

Signed 16-bit decimal number.

UINT16

Unsigned 16-bit decimal number.

INT32

Signed 32-bit decimal number.

UINT32

Unsigned 32-bit decimal number.

INT64

Signed 64-bit decimal number.

UINT64

Unsigned 64-bit decimal number.

DOUBLE

Two dot-separated signed 32-bit decimal numbers. The format is [INTEGER].[INTEGER].

HEX

Hexadecimal number.

CHAR

Single character.

STRING

Character string.

IPADDR

IP address.

MAC

MAC address.

DATE

Date.

TIME

Time.

 

Managing and obtaining system log messages

You can manage system log messages by using the information center.

By default, the information center is enabled. Log messages can be output to the console, log buffer, monitor terminal, log host, and log file.

To filter log messages, use the info-center source command to specify log output rules. A log output rule specifies the source modules and the lowest severity level of log messages that can be output to a destination. A log message is output if its severity level is higher than or equal to the specified level. For example, if you specify a severity level of 6 (informational), log messages that have a severity level from 0 to 6 are output.

For more information about using the information center, see the network management and monitoring configuration guide for the product.

Obtaining log messages from the console terminal

Access the device through the console port. Real-time log messages are displayed on the console terminal.

Obtaining log messages from the log buffer

Use the display logbuffer command to display history log messages in the log buffer.

Obtaining log messages from a monitor terminal

Monitor terminals refer to terminals that access the device through the AUX, VTY, or TTY lines (for example, Telnet). To obtain log messages from a monitor terminal, use the following guidelines:

·           To display log messages on the monitor terminal, you must configure the terminal monitor command.

·           For monitor terminals, the lowest level of log messages that can be displayed is determined by both the terminal logging level and info-center source commands.

Obtaining log messages from the log file

By default, the log file feature automatically saves logs from the log file buffer to the log file every 24 hours. You can use the info-center logfile frequency command to change the automatic saving internal.

To manually save logs to the log file, use the logfile save command. The log file buffer is cleared each time a save operation is performed.

By default, you can obtain the log file from the cfa0:/logfile/ path if the CF card is not partitioned. If the CF card is partitioned, the file path is cfa1:/logfile/.

Obtaining log messages from a log host

Use the info-center loghost command to specify the service port number and IP address of a log host. To specify multiple log hosts, repeat the command.

For a successful log message transmission, make sure the specified port number is the same as the port number used on the log host. The default service port number is 514.

Software module list

Table 4 lists all software modules that might produce system log messages. This document uses "OPENSRC" to represent all open source modules.

Table 4 Software module list

Module name representation

Module name expansion

AAA

Authentication, Authorization and Accounting

ACL

Access Control List

ANCP

Access Node Control Protocol

APMGR

Access Point Management

ARP

Address Resolution Protocol

ATK

Attack Detection and Prevention

ATM

Asynchronous Transfer Mode

BFD

Bidirectional Forwarding Detection

BGP

Border Gateway Protocol

BLS

Blacklist

CFD

Connectivity Fault Detection

CFGMAN

Configuration Management

CONNLMT

Connection Limit

DEV

Device Management

DHCP

Dynamic Host Configuration Protocol

DHCPR

IPv4 DHCP Relay

DHCPS

DHCP Server

DHCPS6

DHCPv6 Server

DHCPSP4

DHCP Snooping

DHCPSP6

DHCPv6 Snooping

DIAG

Diagnosis

DLDP

Device Link Detection Protocol

DOT1X

802.1X

DRNI

Distributed Resilient Network Interconnect

EDEV

Extended-Device Management

ERPS

Ethernet Ring Protection Switching

ETHOAM

Ethernet Operation, Administration and Maintenance

EVB

Edge Virtual Bridging

EVIISIS

Ethernet Virtual Interconnect Intermediate System-to-Intermediate System

FCOE

Fibre Channel Over Ethernet

FCLINK

Fibre Channel Link

FCZONE

Fibre Channel Zone

FIB

Forwarding Information Base

FILTER

Filter

FIPSNG

FIP Snooping

FTPD

File Transfer Protocol Daemon

HA

High Availability

HQOS

Hierarchical QoS

HTTPD

Hypertext Transfer Protocol Daemon

IFNET

Interface Net Management

IKE

Internet Key Exchange

IPADDR

IP address

IPFW

IP Forwarding

IPSEC

IP Security

IPSG

IP Source Guard

IRDP

ICMP Router Discovery Protocol

ISIS

Intermediate System-to-Intermediate System

ISSU

In-Service Software Upgrade

L2TP

Layer 2 Tunneling Protocol

L2VPN

Layer 2 VPN

LAGG

Link Aggregation

LDP

Label Distribution Protocol

LLDP

Link Layer Discovery Protocol

LOAD

Load Management

LOGIN

Login

LPDT

Loopback Detection

LS

Local Server

LSPV

LSP Verification

MAC

Media Access Control

MACA

MAC Authentication

MACSEC

MAC Security

MBFD

MPLS BFD

MBUF

Memory buffer

MDC

Multitenant Device Context

MFIB

Multicast Forwarding Information Base

MGROUP

Mirroring group

MPLS

Multiprotocol Label Switching

MTLK

Monitor Link

NAT

Network Address Translation

NETCONF

Network Configuration Protocol

ND

Neighbor Discovery

NQA

Network Quality Analyzer

NTP

Network Time Protocol

OPENSRC

Open Source

OBJP

Object Policy

OFP

OpenFlow Protocol

OPTMOD

Optical Module

OSPF

Open Shortest Path First

OSPFV3

Open Shortest Path First Version 3

PKTCPT

Packet Capture

PFILTER

Packet Filter

PBB

Provider Backbone Bridge

PBR

Policy-Based Routing

PCE

Path Computation Element

PEX

Port Extender

PIM

Protocol Independent Multicast

PING

Packet Internet Groper

PKI

Public Key Infrastructure

PKT2CPU

Packet to CPU

PORTSEC

Port Security

PPP

Point to Point Protocol

PWDCTL

Password Control

QOS

Quality of Service

RADIUS

Remote Authentication Dial In User Service

RDDC

Redundancy

RIP

Routing Information Protocol

RIPNG

Routing Information Protocol Next Generation

RM

Routing Management

RRPP

Rapid Ring Protection Protocol

RTM

Real-Time Event Manager

SCM

Service Control Manager

SCRLSP

Static CRLSP

SESSION

Session

SFLOW

Sampler Flow

SHELL

Shell

SLSP

Static LSP

SMLK

Smart Link

SNMP

Simple Network Management Protocol

SSHC

Secure Shell Client

SSHS

Secure Shell Server

STAMGR

Station Management

STM

Stack Topology Management

STP

Spanning Tree Protocol

SYSEVENT

System Event

SYSLOG

System Log

TACACS

Terminal Access Controller Access Control System

TELNETD

Telnet Daemon

TRILL

Transparent Interconnect of Lots of Links

VCF

Vertical Converged Framework

VLAN

Virtual Local Area Network

VRRP

Virtual Router Redundancy Protocol

VSRP

Virtual Service Redundancy Protocol

VXLAN

Virtual eXtensible LAN

WIPS

Wireless Intrusion Prevention System

 

Using this document

This document categorizes system log messages by software module. The modules are ordered alphabetically. Except for OPENSRC, the system log messages for each module are listed in alphabetic order of their mnemonic names. The OPENSRC messages are unordered because they use the same mnemonic name (SYSLOG). For each OPENSRC message, the section title uses a short description instead of the mnemonic name.

This document explains messages in tables. Table 5 describes information provided in these tables.

Table 5 Message explanation table contents

Item

Content

Example

Message text

Presents the message description.

ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

Briefly describes the variable fields in the order that they appear in the message text.

The variable fields are numbered in the "$Number" form to help you identify their location in the message text.

$1: ACL number.

$2: ID and content of an ACL rule.

$3: Number of packets that matched the rule.

Severity level

Provides the severity level of the message.

6

Example

Provides a real message example. The examples do not include the "<PRI>TIMESTAMP Sysname %%vendor" part or the "Prefix TIMESTAMP Sysname" part, because information in this part varies with system settings.

ACL/6/ACL_STATIS_INFO: ACL 2000 rule 0 permit source 1.1.1.1 0 logging 10000 packet(s).

Explanation

Explains the message, including the event or error cause.

Number of packets that matched an ACL rule. This message is sent when the packet counter changes.

Recommended action

Provides recommended actions. For informational messages, no action is required.

No action is required.

 

 

AAA messages

This section contains AAA messages.

AAA_FAILURE

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA failed.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

5

Example

AAA/5/AAA_FAILURE: -AAAType=AUTHOR-AAADomain=domain1-Service=login-UserName=cwf@system; AAA failed.

Explanation

An AAA request was rejected.

The following are the common reasons:

·          No response was received from the server.

·          The username or password was incorrect.

·          The service type that the user applied for was incorrect.

Recommended action

1.      Verify that the device is correctly connected to the server.

2.      Enter the correct username and password.

3.      Verify that the server settings are the same as the settings on the device.

4.      If the problem persists, contact H3C Support.

 

AAA_LAUNCH

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA launched.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

6

Example

AAA/6/AAA_LAUNCH: -AAAType=AUTHEN-AAADomain=domain1-Service=login-UserName=cwf@system; AAA launched.

Explanation

An AAA request was received.

Recommended action

No action is required.

 

AAA_SUCCESS

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA succeeded.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

6

Example

AAA/6/AAA_SUCCESS: -AAAType=AUTHOR-AAADomain=domain1-Service=login-UserName=cwf@system; AAA succeeded.

Explanation

An AAA request was accepted.

Recommended action

No action is required.

 

ACL messages

This section contains ACL messages.

ACL_ACCELERATE_NO_RES

Message text

Failed to accelerate [STRING] ACL [UINT32]. The resources are insufficient.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NO_RES: Failed to accelerate IPv6 ACL 2001. The resources are insufficient.

Explanation

Hardware resources were insufficient for accelerating an ACL.

Recommended action

Delete some rules or disabled ACL acceleration for other ACLs to release hardware resources.

 

ACL_ACCELERATE_NONCONTIGUOUSMASK

Message text

Failed to accelerate ACL [UINT32]. ACL acceleration supports only contiguous wildcard masks.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NONCONTIGUOUSMASK: Failed to accelerate ACL 2001. ACL acceleration supports only contiguous wildcard masks.

Explanation

ACL acceleration failed because rules containing noncontiguous wildcard masks exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_NOT_SUPPORT

Message text

Failed to accelerate [STRING] ACL [UINT32]. The operation is not supported.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORT: Failed to accelerate IPv6 ACL 2001. The operation is not supported.

Explanation

ACL acceleration failed because the system does not support ACL acceleration.

Recommended action

No action is required.

 

ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP

Message text

Failed to accelerate IPv6 ACL [UINT32]. ACL acceleration does not support the rules that contain the hop-by-hop keywords.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP: Failed to accelerate IPv6 ACL 2001. ACL acceleration does not support the rules that contain the hop-by-hop keywords.

Explanation

ACL acceleration failed for the IPv6 ACL because rules containing the hop-by-hop keyword exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG

Message text

Failed to accelerate IPv6 ACL [UINT32]. ACL acceleration does not support specifying multiple TCP flags in one rule.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG: Failed to accelerate IPv6 ACL 2001. ACL acceleration does not support specifying multiple TCP flags in one rule.

Explanation

ACL acceleration failed for the IPv6 ACL because rules containing multiple TCP flags exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_UNK_ERR

Message text

Failed to accelerate [STRING] ACL [UINT32].

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_UNK_ERR: Failed to accelerate IPv6 ACL 2001.

Explanation

ACL acceleration failed because of an unknown error.

Recommended action

No action is required.

 

ACL_IPV6_STATIS_INFO

Message text

IPv6 ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

$1: ACL number.

$2: ID and content of an IPv6 ACL rule.

$3: Number of packets that matched the rule.

Severity level

6

Example

ACL6/6/ACL_IPV6_STATIS_INFO: IPv6 ACL 2000 rule 0 permit source 1:1::/64 logging 1000 packet(s).

Explanation

The number of packets matching the IPv6 ACL rule changed.

Recommended action

No action is required.

 

ACL_NO_MEM

Message text

Failed to configure [STRING] ACL [UINT] due to lack of memory.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

3

Example

ACL/3/ACL_NO_MEM: Failed to configure ACL 2001 due to lack of memory.

Explanation

Configuring the ACL failed because memory is insufficient.

Recommended action

Use the display memory-threshold command to check the memory usage.

 

ACL_STATIS_INFO

Message text

ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

$1: ACL number.

$2: ID and content of an IPv4 ACL rule.

$3: Number of packets that matched the rule.

Severity level

6

Example

ACL/6/ACL_STATIS_INFO: ACL 2000 rule 0 permit source 1.1.1.1 0 logging 10000 packet(s).

Explanation

The number of packets matching the IPv4 ACL rule changed.

Recommended action

No action is required.

 

 

ANCP messages

This section contains ANCP messages.

ANCP_INVALID_PACKET

Message text

-NeighborName=[STRING]-State=[STRING]-MessageType=[STRING]; The [STRING] value [STRING] is wrong, and the value [STRING] is expected.

Variable fields

$1: ANCP neighbor name.

$2: Neighbor state.

$3: Message type.

$4: Field.

$5: Wrong value of the field.

$6: Expected value of the field.

Severity level

6

Example

ANCP/6/ANCP_INVALID_PACKET: -NeighborName=Dslam-State=SYNSENT-MessageType=SYNACK; The Sender Instance value 0 is wrong, and the value 1 is expected.

Explanation

The system received an adjacency message that had a field with a wrong value.

Recommended action

No action is required.

 

API

This section contains API messages.

DRVPLAT/2/DrvDebug

Message text

A minimum of one switching fabric module is required in the first, third, fourth, or fifth slot for switching fabric modules.

Variable fields

N/A

Severity level

2

Example

DRVPLAT/2/DrvDebug: -MDC=1; A minimum of one switching fabric module is required in the first, third, fourth, or fifth slot for switching fabric modules.

Explanation

An S10508X-V or S10516X switch cannot operate correctly and outputs this message if only its second switching fabric module slot has a switching fabric module. For an S10508X-V switch, the second switching fabric module slot is slot 11. For an S10516X switch, the second switching fabric module slot is slot 19.

Recommended action

For an S10508X-V switch, make sure a minimum of one switching fabric module is installed in slot 10, 12, 13, or 14. For an S10516X switch, make sure a minimum of one switching fabric module is installed in slot 18, 20, 21, or 22.

 

DRVPLAT/4/DrvDebug

Message text

The device doesn't support power module [INT32].

Variable fields

$1: Power module ID.

Severity level

4

Example

DRVPLAT/4/DrvDebug: -MDC=1; The device doesn't support power module 1.

Explanation

An S10516X switch does not support the type of power module.

Recommended action

Replace the power module.

 

DRVPLAT/4/DrvDebug

Message text

WARNING: A switching fabric module was installed in the second switching fabric module slot while the first, third, fourth, or fifth switching fabric module slot was empty. Please move the module to one of the specified slots that are empty.

Variable fields

N/A

Severity level

4

Example

DRVPLAT/4/DrvDebug: -MDC=1; WARNING:  A switching fabric module was installed in the second switching fabric module slot while the first, third, fourth, or fifth switching fabric module slot was empty. Please move the module to one of the specified slots that are empty.

Explanation

On an S10508X-V switch, you can install a switching fabric module in slot 11 only if slots 10, 12, 13, and 14 are all installed with switching fabric modules. On an S10516X switch, you can install a switching fabric module in slot 19 only if slots 18, 20, 21, and 22 are all installed with switching fabric modules.

Recommended action

On an S10508X-V switch, do not install a switching fabric module in slot 11 while slot 10, 12, 13, or 14 is empty.  On an S10516X switch, do not install a switching fabric module in slot 19 while slot 18, 20, 21, or 22 is empty.

 

APMGR messages

This section contains access point management messages.

APMGR_AC_MEM_ALERT

Message text

The memory utilization has reached the threshold.

Variable fields

N/A

Severity level

4

Example

APMGR/4/APMGR_AC_MEM_ALERT: The memory utilization has reached the threshold.

Explanation

The AP failed to come online because the memory utilization exceeded the limit.

Recommended action

Stop creating manual APs and prevent APs from coming online.

 

APMGR_ADD_AP_FAIL

Message text

AP [STRING] failed to come online using serial ID [STRING]: MAC address [STRING] is being used by AP [STRING].

Variable fields

$1: AP name.

$2: Serial ID.

$3: MAC address.

$4: AP name.

Severity level

4

Example

APMGR/4/ APMGR_ADD_AP_FAIL: AP ap1 failed to come online using serial ID 01247ef96: MAC address 0023-7961-5201 is being used by AP ap2.

Explanation

The AP failed to come online because a manual AP that has the same MAC address already exists on the AC.

Recommended action

Delete either the manual AP that has the MAC address or the serial ID.

 

APMGR_ADDBAC_INFO

Message text

Add BAS AC [STRING].

Variable fields

$1: MAC address of the BAS AC.

Severity level

6

Example

APMGR/6/APMGR_ADDBAC_INFO: Add BAS AC 3ce5-a616-28cd.

Explanation

The BAS AC was connected to the master AC.

Recommended action

No action is required.

 

APMGR_AP_OFFLINE

Message text

AP [STRING] went offline. State changed to Idle.

Variable fields

$1: AP name.

Severity level

6

Example

APMGR/6/APMGR_AP_OFFLINE: AP ap1 went offline. State changed to Idle.

Explanation

The AP went offline. The state of the AP changed to Idle.

Recommended action

If the AP went offline abnormally, check the debugging information to locate the issue and resolve it.

 

APMGR_AP_ONLINE

Message text

AP [STRING] went online. State changed to Run.

Variable fields

$1: AP name.

Severity level

6

Example

APMGR/6/APMGR_AP_ONLINE: AP ap1 went online. State changed to Run.

Explanation

The AP came online. The state of the AP changed to Run.

Recommended action

No action is required.

 

APMGR_CWC_IMG_DOWNLOAD_COMPLETE

Message text

System software image file [STRING] downloading through the CAPWAP tunnel to AC [STRING] completed.

Variable fields

$1: Image file name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_DOWNLOAD_COMPLETE: System software image file 5800.ipe downloading through the CAPWAP tunnel to AC 192.168.10.1 completed.

Explanation

The AP downloaded the image file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWC_IMG_DOWNLOAD_START

Message text

Started to download the system software image file [STRING] through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: Image file name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_DOWNLOAD_START: Started to download the system software image file 5800.ipe through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP started to download the image file from the AC.

Recommended action

Make sure the AP is correctly connected to the AC.

 

APMGR_CWC_IMG_NO_ENOUGH_SPACE

Message text

Insufficient flash memory space for downloading system software image file [STRING].

Variable fields

$1: Image file name.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_NO_ENOUGH_SPACE: Insufficient flash memory space for downloading system software image file 5800.ipe.

Explanation

The AP failed to download the image file from the AC because of insufficient flash memory.

Recommended action

Delete files not in use from the AP.

 

APMGR_CWC_LOCAL_AC_DOWN

Message text

CAPWAP tunnel to Central AC [STRING] went down. Reason: [STRING].

Variable fields

$1: IP address of the central AC.

$2: Reason:

·          Added local AC IP address.

·          Deleted local AC IP address.

·          Local AC interface used for CAPWAP tunnel went down.

·          Local AC config changed.

·          N/A

Severity level

4

Example

APMGR/4/APMGR_CWC_LOCAL_AC_DOWN: CAPWAP tunnel to Central AC 2.2.2.1 went down. Reason: Added local AC IP address.

Explanation

The CAPWAP tunnel between the central AC and the local AC was terminated for a specific reason.

Recommended action

To resolve the issue:

1.      Examine the network connection between the central AC and the local AC.

2.      Verify that the central AC is correctly configured.

3.      Verify that the local AC is correctly configured.

4.      If the issue persists, contact H3C Support.

 

APMGR_CWC_LOCAL_AC_UP

Message text

CAPWAP tunnel to Central AC [STRING] went up.

Variable fields

$1: IP address of the central AC.

Severity level

6

Example

APMGR/6/APMGR_CWC_LOCAL_AC_UP: CAPWAP tunnel to Central AC 2.2.2.1 went up.

Explanation

The central AC has established a CAPWAP tunnel with the local AC.

Recommended action

No action is required.

 

APMGR_CWC_REBOOT

Message text

AP in state [STRING] is rebooting. Reason: [STRING]

Variable fields

$1: AP state.

$2: Reason:

·          AP was reset.

·          Image was downloaded successfully.

·          AP stayed in idle state for a long time.

Severity level

6

Example

APMGR/6/APMGR_CWC_REBOOT: AP in State Run is rebooting. Reason: AP was reset.

Explanation

The AP rebooted for a specific reason.

Recommended action

No action is required.

 

APMGR_CWC_RUN_DOWNLOAD_COMPLETE

Message text

File [STRING] successfully downloaded through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: File name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_DOWNLOAD_COMPLETE: File ac.cfg successfully downloaded through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP downloaded the file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWC_RUN_DOWNLOAD_START

Message text

Started to download the file [STRING] through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: File name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_DOWNLOAD_START: Started to download the file ac.cfg through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP started to download the file from the AC.

Recommended action

Make sure the AP is correctly connected to the AC.

 

APMGR_CWC_RUN_NO_ENOUGH_SPACE

Message text

Insufficient flash memory space for downloading file [STRING].

Variable fields

$1: File name.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_NO_ENOUGH_SPACE: Insufficient flash memory space for downloading file ac.cfg.

Explanation

The AP failed to download the file from the AC because of insufficient flash memory.

Recommended action

Delete files not in use from the AP.

 

APMGR_CWC_TUNNEL_DOWN

Message text

CAPWAP tunnel to AC [STRING] went down. Reason: [STRING].

Variable fields

$1: AC IP address.

$2: Reason:

·          Added AP IP address.

·          Deleted AP IP address.

·          AP interface used for CAPWAP tunnel went down.

·          AP config changed.

·          AP was reset.

·          Number of echo retransmission attempts exceeded the limit.

·          Full retransmission queue.

·          Data channel timer expired.

·          Backup AC IP address changed.

·          Backup tunnel changed to master tunnel.

·          Failed to change backup tunnel to master tunnel.

·          Backup method changed.

·          N/A.

Severity level

6

Example

APMGR/6/APMGR_CWC_TUNNEL_DOWN: CAPWAP tunnel to AC 192.168.10.1 went down. Reason: AP was reset.

Explanation

The CAPWAP tunnel between the AP and the AC was terminated for a specific reason.

Recommended action

Examine the network connection between the AP and the AC.

 

APMGR_CWC_TUNNEL_UP

Message text

[STRING] CAPWAP tunnel to AC [STRING] went up.

Variable fields

$1: Tunnel type:

·          Master.

·          Backup.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_TUNNEL_UP: Master CAPWAP tunnel to AC 192.168.10.1 went up.

Explanation

The AP was connected to the AC successfully and entered Run state.

Recommended action

No action is required.

 

APMGR_CWS_IMG_DOWNLOAD_COMPLETE

Message text

System software image file [STRING] downloading through the CAPWAP tunnel for AP [STRING] completed.

Variable fields

$1: Image file name.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_ CWS_IMG_DOWNLOAD_COMPLETE: System software image file 5800.ipe downloading through the CAPWAP tunnel for AP ap2 completed.

Explanation

The AP downloaded the image file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWS_IMG_DOWNLOAD_START

Message text

AP [STRING] started to download the system software image file [STRING].

Variable fields

$1: AP name.

$2: Image file name.

Severity level

6

Example

APMGR/6/APMGR_CWS_IMG_DOWNLOAD_START: AP ap1 started to download the system software image file 5800.ipe.

Explanation

The AP started to download the image file from the AC.

Recommended action

No action is required.

 

APMGR_CWS_LOCAL_AC_DOWN

Message text

CAPWAP tunnel to local AC [STRING] went down. Reason: [STRING].

Variable fields

$1: IP address of the local AC.

$2: Reason:

·          Neighbor dead timer expired.

·          Local AC was deleted.

·          Serial number changed.

·          Processed join request in Run state.

·          Failed to retransmit message.

·          N/A

Severity level

4

Example

APMGR/4/APMGR_CWS_LOCAL_AC_DOWN: CAPWAP tunnel to local AC 1.1.1.1 went down. Reason: Serial number changed.

Explanation

The CAPWAP tunnel between the central AC and the local AC was terminated for a specific reason.

Recommended action

To resolve the issue:

1.      Examine the network connection between the central AC and the local AC.

2.      Verify that the central AC is correctly configured.

3.      Verify that the local AC is correctly configured.

4.      If the issue persists, contact H3C Support.

 

APMGR_CWS_LOCAL_AC_UP

Message text

CAPWAP tunnel to local AC [STRING] went up.

Variable fields

$1: IP address of the local AC.

Severity level

6

Example

APMGR/6/APMGR_CWS_LOCAL_AC_UP: CAPWAP tunnel to local AC 1.1.1.1 went up.

Explanation

The central AC has established a CAPWAP tunnel with the local AC.

Recommended action

No action is required.

 

APMGR_CWS_RUN_DOWNLOAD_COMPLETE

Message text

File [STRING] successfully downloaded through the CAPWAP tunnel for AP [STRING].

Variable fields

$1: File name.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_CWS_RUN_DOWNLOAD_COMPLETE: File ac.cfg successfully downloaded through the CAPWAP tunnel for AP ap2.

Explanation

The AP downloaded the file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWS_RUN_DOWNLOAD_START

Message text

AP [STRING] started to download the file [STRING].

Variable fields

$1: AP name.

$2: File name.

Severity level

6

Example

APMGR/6/APMGR_CWS_RUN_DOWNLOAD_START: AP ap1 started to download the file ac.cfg.

Explanation

The AP started to download the file from the AC.

Recommended action

No action is required.

 

APMGR_CWS_TUNNEL_DOWN

Message text

CAPWAP tunnel to AP [STRING] went down. Reason: [STRING].

Variable fields

$1: AP name.

$2: Reason:

·          Neighbor dead timer expired.

·          AP was reset.

·          AP was deleted.

·          Serial number changed.

·          Processed join request in Run state.

·          Failed to retransmit message.

·          Received WTP tunnel down event from AP.

·          Backup AC closed the backup tunnel.

·          Tunnel switched.

·          N/A.

Severity level

6

Example

APMGR/6/APMGR_CWS_TUNNEL_DOWN: CAPWAP tunnel to AP ap1 went down. Reason: AP was reset.

Explanation

The AP went offline for a specific reason.

Recommended action

To resolve the issue:

1.      Examine the network connection between the AP and the AC.

2.      Verify that the AP is correctly configured.

3.      Verify that the AC is correctly configured.

4.      If the issue persists, contact H3C Support.

 

APMGR_CWS_TUNNEL_UP

Message text

[STRING] CAPWAP tunnel to AP [STRING] went up.

Variable fields

$1: Tunnel type:

·          Master.

·          Backup.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_CWS_TUNNEL_UP: Backup CAPWAP tunnel to AP ap1 went up.

Explanation

The AP came online and entered Run state.

Recommended action

No action is required.

 

APMGR_DELBAC_INFO

Message text

Delete BAS AC [STRING].

Variable fields

$1: MAC address of the BAS AC.

Severity level

6

Example

APMGR/6/APMGR_DELBAC_INFO: Delete BAS AC 3ce5-a616-28cd.

Explanation

The BAS AC was disconnected from the master AC.

Recommended action

No action is required.

 

APMGR_LOCAL_AC_OFFLINE

Message text

Local AC [STRING] went offline. State changed to Idle.

Variable fields

$1: Name of the local AC.

Severity level

6

Example

APMGR/6/APMGR_LOCAL_AC_OFFLINE: Local AC ac1 went offline. State changed to Idle.

Explanation

The local AC went offline. The state of the local AC changed to Idle.

Recommended action

1.      If the local AC went offline abnormally, check the debugging information to locate the issue and resolve it.

2.      If the issue persists, contact H3C Support.

 

APMGR_LOCAL_AC_ONLINE

Message text

Local AC [STRING] went online. State changed to Run.

Variable fields

$1: Name of the local AC.

Severity level

6

Example

APMGR/6/APMGR_LOCAL_AC_ONLINE: Local AC ac1 went online. State changed to Run.

Explanation

The local AC came online. The state of the local AC changed to Run.

Recommended action

No action is required.

 

 

 

ARP messages

This section contains ARP messages.

ARP_ACTIVE_ACK_NO_REPLY

Message text

No ARP reply from IP [STRING] was received on interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_ACTIVE_ACK_NO_REPLY: No ARP reply from IP 192.168.10.1 was received on interface GigabitEthernet1/0/1.

Explanation

The ARP active acknowledgement feature did not receive an ARP reply after it sent an ARP request to the sender IP of an ARP message.

This message indicates the risk of attacks.

Recommended action

1.      Verify that the learned ARP entries on the device are consistent with the existing legal devices. When gateways and servers are on the network, check the ARP entries for these devices first.

2.      If the ARP entries are correct and the attack continues, contact H3C Support.

 

ARP_ACTIVE_ACK_NOREQUESTED_REPLY

Message text

Interface [STRING] received from IP [STRING] an ARP reply that was not requested by the device.

Variable fields

$1: Interface name.

$2: IP address.

Severity level

6

Example

ARP/6/ARP_ACTIVE_ACK_NOREQUESTED_REPLY: Interface GigabitEthernet1/0/1 received from IP 192.168.10.1 an ARP reply that was not requested by the device.

Explanation

The ARP active acknowledgement feature received an unsolicited ARP reply from a sender IP.

This message indicates the risk of attacks.

Recommended action

No action is required. The device discards the ARP reply automatically.

 

ARP_BINDRULETOHW_FAILED

Message text

Failed to download binding rule to hardware on the interface [STRING], SrcIP [IPADDR], SrcMAC [MAC], VLAN [UINT16], Gateway MAC [MAC].

Variable fields

$1: Interface name.

$2: Source IP address.

$3: Source MAC address.

$4: VLAN ID.

$5: Gateway MAC address.

Severity level

5

Example

ARP/5/ARP_BINDRULETOHW_FAILED: Failed to download binding rule to hardware on the interface GigabitEthernet1/0/1, SrcIP 1.1.1.132, SrcMAC 0015-E944-A947, VLAN 1, Gateway MAC 00A1-B812-1108.

Explanation

The system failed to set a binding rule to the hardware on an interface. The message is sent in any of the following situations:

·          The resources are not sufficient for the operation.

·          The memory is not sufficient for the operation.

·          A hardware error occurs.

Recommended action

To resolve the problem:

1.      Execute the display qos-acl resource command to check if the ACL resources for the operation are sufficient.

¡  If yes, proceed to step 2.

¡  If no, delete unnecessary configuration to release ACL resources. If no configuration can be deleted, proceed to step 2.

2.      Execute the display memory command to check if the memory for the operation is sufficient.

¡  If yes, proceed to step 3.

¡  If no, delete unnecessary configuration to release memory. If no configuration can be deleted, proceed to step 3.

3.      Delete the configuration and perform the operation again.

 

ARP_DETECTION_LOG

Message text

Detected an ARP attack on interface [STRING]: IP [STRING], MAC [STRING], VLAN [STRING]. [UINT32] packet(s) dropped.

Variable fields

$1: Interface name.

$2: IP address.

$3: MAC address.

$4: VLAN ID.

$5: Number of dropped packets.

Severity level

5

Example

ARP/5/ARP_INSPECTION: -MDC=1; Detected an ARP attack on interface GigabitEthernet1/0/1: IP 1.1.1.1, MAC 1-1-1, VLAN 100. 2 packet(s) dropped.

Explanation

An ARP attack was detected on an interface and attack packets were dropped.

Recommended action

Check the source of the ARP attack.

 

ARP_DUPLICATE_IPADDR_DETECT

Message text

Detected an IP address conflict. The device with MAC address [STRING] connected to interface [STRING] in VSI [STRING] and the device with MAC address [STRING] connected to interface [STRING] in VSI [STRING] were using the same IP address [IPADDR].

Variable fields

$1: MAC address.

$2: Interface name. (The interface can be a tunnel interface, Layer 3 interface, or Ethernet service instance.)

$3: VSI name.

$4: MAC address.

$5: Interface name. (The interface can be a tunnel interface, Layer 3 interface, or Ethernet service instance.)

$6: VSI name.

$7: Conflicting IP address.

Severity level

6

Example

ARP/6/ ARP_DUPLICATE_IPADDR_DETECT: Detected an IP address conflict. The device with MAC address 00-00-01 connected to interface GigabitEthernet1/0/1 service-instance 1000 in VSI vpna and the device with MAC address 00-00-02 connected to interface tunnel 10 in VSI vpna were using the same IP address 192.168.1.1.

Explanation

This message is sent when an interface receives an ARP message in which the sender information conflicts with an existing ARP entry. The sender IP address is the same as the IP address in the entry, but the MAC addresses are different.

Recommended action

Change the IP address on either of the two devices.

 

ARP_DYNAMIC

Message text

The maximum number of dynamic ARP entries for the device reached.

Variable fields

N/A

Severity level

6

Example

ARP/6/ARP_DYNAMIC: The maximum number of dynamic ARP entries for the device reached.

Explanation

The maximum number of dynamic ARP entries for the device was reached.

Recommended action

No action is required.

 

ARP_DYNAMIC_IF

Message text

The maximum number of dynamic ARP entries for interface [STRING] reached.

Variable fields

$1: Interface name.

Severity level

6

Example

ARP/6/ARP_DYNAMIC_IF: The maximum number of dynamic ARP entries for interface GigabitEthernet1/0/1 reached.

Explanation

The maximum number of dynamic ARP entries for the specified interface was reached.

Recommended action

No action is required.

 

ARP_DYNAMIC_SLOT

Message text

Pattern 1:

The maximum number of dynamic ARP entries for slot [INT32] reached.

Pattern 2:

The maximum number of dynamic ARP entries for chassis [INT32] slot [INT32] reached.

Variable fields

Pattern 1:

$1: Slot number.

Pattern 2:

$1: Chassis number.

$2: Slot number.

Severity level

6

Example

ARP/6/ARP_DYNAMIC_SLOT: The maximum number of dynamic ARP entries for slot 2 reached.

Explanation

Pattern 1:

The maximum number of dynamic ARP entries for the slot was reached.

Pattern 2:

The maximum number of dynamic ARP entries for the slot on the chassis was reached.

Recommended action

No action is required.

 

ARP_ENTRY_CONFLICT

Message text

The software entry for [STRING] on [STRING] and the hardware entry did not have the same [STRING].

Variable fields

$1: IP address.

$2: VPN instance name. If the ARP entry belongs to the public network, this field displays the public network.

$3: Inconsistent items:

¡  MAC address.

¡  output interface.

¡  output port.

¡  outermost layer VLAN ID.

¡  second outermost layer VLAN ID.

¡  VSI index.

¡  link ID.

Severity level

6

Example

ARP/6/ARP_ENTRY_CONFLICT: The software entry for 1.1.1.1 on the VPN a and the hardware entry did not have the same MAC address, output port, VSI index, and link ID.

ARP/6/ARP_ENTRY_CONFLICT: The software entry for 1.1.1.2 on the public  network and the hardware entry did not have the same MAC address, output port, VSI index, and link ID.

Explanation

The software entry for the specified IP address is not the same as the hardware entry. For example, they do not have the same output interface.

Recommended action

No action is required. ARP automatically refreshes the hardware entries.

 

ARP_HOST_IP_CONFLICT

Message text

The host [STRING] connected to interface [STRING] cannot communicate correctly, because it uses the same IP address as the host connected to interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: Interface name.

Severity level

4

Example

ARP/4/ARP_HOST_IP_CONFLICT: The host 1.1.1.1 connected to interface GigabitEthernet1/0/1 cannot communicate correctly, because it uses the same IP address as the host connected to interface GigabitEthernet1/0/2.

Explanation

The sender IP address in a received ARP message conflicted with the IP address of a host connected to another interface.

Recommended action

Check whether the hosts that send the ARP messages are legitimate. Disconnect the illegal host from the network.

 

ARP_LOCALPROXY_ENABLE_FAILED

Message text

Failed to enable local proxy ARP on interface [STRING].

Variable fields

$1: Interface name.

Severity level

4

Example

ARP/4/ARP_LOCALPROXY_ENABLE_FAILED: -MDC=1-Slot=2; Failed to enable local proxy ARP on interface VSI-interface 1.

Explanation

This message is sent when the device fails to enable local proxy ARP on an interface in a slot. If the interface resides on the MPU, the slot number is 0.

Recommended action

1.      Verify that the card supports local proxy ARP.

2.      Verify that sufficient hardware resources are available.

 

ARP_RATE_EXCEEDED

Message text

The ARP packet rate ([UINT32] pps) exceeded the rate limit ([UINT32] pps) on interface [STRING] in the last [UINT32] seconds.

Variable fields

$1: ARP packet rate.

$2: ARP limit rate.

$3: Interface name.

$4: Interval time.

Severity level

4

Example

ARP/4/ARP_RATE_EXCEEDED: The ARP packet rate (100 pps) exceeded the rate limit (80 pps) on interface GigabitEthernet1/0/1 in the last 10 seconds.

Explanation

An interface received ARP messages at a higher rate than the rate limit.

Recommended action

Verify that the hosts at the sender IP addresses are legitimate.

 

ARP_RATELIMIT_NOTSUPPORT

Message text

Pattern 1:

ARP packet rate limit is not support on slot [INT32].

Pattern 2:

ARP packet rate limit is not support on chassis [INT32] slot [INT32].

Variable fields

Pattern 1:

$1: Slot number.

Pattern 2:

$1: Chassis number.

$2: Slot number.

Severity level

6

Example

ARP/6/ARP_RATELIMIT_NOTSUPPORT: ARP packet rate limit is not support on slot 2.

Explanation

Pattern 1:

ARP packet rate limit is not supported on the slot.

Pattern 2:

ARP packet rate limit is not supported on the slot of the chassis was reached.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_SENDER_IP_INVALID

Message text

Sender IP [STRING] was not on the same network as the receiving interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_SENDER_IP_INVALID: Sender IP 192.168.10.2 was not on the same network as the receiving interface GigabitEthernet1/0/1.

Explanation

The sender IP of a received ARP message was not on the same network as the receiving interface.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_SENDER_MAC_INVALID

Message text

Sender MAC [STRING] was not identical to Ethernet source MAC [STRING] on interface [STRING].

Variable fields

$1: MAC address.

$2: MAC address.

$3: Interface name.

Severity level

6

Example

ARP/6/ARP_SENDER_MAC_INVALID: Sender MAC 0000-5E14-0E00 was not identical to Ethernet source MAC 0000-5C14-0E00 on interface GigabitEthernet1/0/1.

Explanation

An interface received an ARP message. The sender MAC address in the message body was not identical to the source MAC address in the Ethernet header.

Recommended action

Verify that the host at the sender MAC address is legitimate.

 

ARP_SENDER_SMACCONFLICT

Message text

Packet was discarded because its sender MAC address was the MAC address of the receiving interface.

Interface: [STRING], sender IP: [STRING], target IP: [STRING].

Variable fields

$1: Interface name.

$2: Sender IP address.

$3: Target IP address.

Severity level

6

Example

ARP/6/ ARP_SENDER_SMACCONFLICT: Packet discarded for the sender MAC address is the same as the receiving interface.

Interface: GigabitEthernet1/0/1 sender IP: 1.1.2.2 target IP: 1.1.2.1,

Explanation

The sender MAC address of a received ARP packet conflicts with the MAC address of the device.

Recommended action

No action is required.

 

ARP_SENDER_SMACCONFLICT_VSI

Message text

Packet was discarded because its sender MAC address was the MAC address of the receiving interface.

Interface: [STRING], sender IP: [STRING], target IP: [STRING],VSI index: [UINT32], link ID: [UINT32].

Variable fields

$1: Interface name.

$2: Sender IP address.

$3: Target IP address.

$4: VSI index.

$5: Link ID.

Severity level

6

Example

ARP/6/ ARP_SENDER_SMACCONFLICT_VSI: Packet discarded for the sender MAC address is the same as the receiving interface.

Interface: VSI3 sender IP: 1.1.2.2 target IP: 1.1.2.1, VSI Index: 2, Link ID: 0

Explanation

The sender MAC address of a received ARP packet conflicts with the MAC address of the device. The receiving interface is a VSI interface.

Recommended action

No action is required.

 

ARP_SRC_MAC_FOUND_ATTACK

Message text

An attack from MAC [STRING] was detected on interface [STRING].

Variable fields

$1: MAC address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_SRC_MAC_FOUND_ATTACK: An attack from MAC 0000-5E14-0E00 was detected on interface GigabitEthernet1/0/1.

Explanation

The source MAC-based ARP attack detection feature received more ARP packets from the same MAC address within 5 seconds than the specified threshold.

This message indicates the risk of attacks.

Recommended action

Verify that the host at the source MAC address is legitimate.

 

ARP_SUP_ENABLE_FAILED

Message text

Failed to enable ARP flood suppression on VSI [STRING].

Variable fields

$1: VSI name.

Severity level

4

Example

ARP/4/ARP_SUP_ENABLE_FAILED: -MDC=1; Failed to enable ARP flood suppression on VSI vpna.

Explanation

This message is sent when the system failed to enable ARP flood suppression for a VSI. The minimum interval between two log messages is 2 seconds. To make the system send the message successfully, wait for a minimum of 2 seconds before you enable ARP flood suppression for another VSI.

Recommended action

1.      Verify that the device supports ARP flood suppression.

2.      Verify that the hardware resources are sufficient.

 

ARP_TARGET_IP_INVALID

Message text

Target IP [STRING] was not the IP of the receiving interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_TARGET_IP_INVALID: Target IP 192.168.10.2 was not the IP of the receiving interface GigabitEthernet1/0/1.

Explanation

The target IP address of a received ARP message was not the IP address of the receiving interface.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_THRESHOLD_REACHED

Message text

The alarm threshold for dynamic ARP entry learning was reached on interface [STRING].

Variable fields

$1: Interface name.

Severity level

4

Example

ARP/4/ARP_THRESHOLD_REACHED: The alarm threshold for dynamic ARP entry learning was reached on interface GigabitEthernet1/0/1.

Explanation

This message is sent when the alarm threshold for dynamic ARP learning was reached on GigabitEthernet 1/0/1.

Recommended action

Verify that the number of learned dynamic ARP entries matches the actual number of devices in the network and no ARP attack sources exist in the network.

 

ARP_USER_DUPLICATE_IPADDR_DETECT

Message text

Detected a user IP address conflict. New user (MAC [STRING], SVLAN [STRING], CVLAN [STRING]) connecting on interface [STRING] and old user (MAC [STRING], SVLAN [STRING], CVLAN [STRING]) connecting on interface [STRING] were using the same IP address [IPADDR].

Variable fields

$1: MAC address of a new user.

$2: Outer VLAN to which the new user belongs.

$3: Inner VLAN to which the new user belongs.

$4: Name of the interface connecting to the new user.

$5: MAC address of an old user.

$6: Outer VLAN to which the old user belongs.

$7: Inner VLAN to which the old user belongs.

$8: Name of the interface connecting to the old user.

$9: IP address.

Severity level

6

Example

ARP/6/ARP_USER_DUPLICATE_IPADDR_DETECT: Detected a user IP address conflict. New user (MAC 0010-2100-01e1, SVLAN 100, CVLAN 10) connecting on interface GigabitEthernet1/0/1 and old user (MAC 0120-1e00-0102, SVLAN 100, CVLAN 10) connecting on interface GigabitEthernet1/0/1 were using the same IP address 192.168.1.1.

Explanation

ARP detected a user IP address conflict. The IP address of a new user is the same as the IP address of an old user.

Recommended action

Verify that all users have different IP addresses.

 

DUPIFIP

Message text

Duplicate address [STRING] on interface [STRING], sourced from [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: MAC Address.

Severity level

6

Example

ARP/6/DUPIFIP: Duplicate address 1.1.1.1 on interface GigabitEthernet1/0/1, sourced from 0015-E944-A947.

Explanation

ARP detected a duplicate address.

The sender IP in the received ARP packet was being used by the receiving interface.

Recommended action

Modify the IP address configuration.

 

DUPIP

Message text

IP address [STRING] conflicted with global or imported IP address, sourced from [STRING].

Variable fields

$1: IP address.

$2: MAC Address.

Severity level

6

Example

ARP/6/DUPIP: IP address 30.1.1.1 conflicted with global or imported IP address, sourced from 0000-0000-0001.

Explanation

The sender IP address of the received ARP packet conflicted with the global or imported IP address.

Recommended action

Modify the IP address configuration.

 

DUPVRRPIP

Message text

IP address [STRING] conflicted with VRRP virtual IP address on interface [STRING], sourced from [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: MAC address.

Severity level

6

Example

ARP/6/DUPVRRPIP: IP address 1.1.1.1 conflicted with VRRP virtual IP address on interface GigabitEthernet1/0/1, sourced from 0015-E944-A947.

Explanation

The sender IP address of the received ARP packet conflicted with the VRRP virtual IP address.

Recommended action

Modify the IP address configuration.

 

 

ATK messages

This section contains attack detection and prevention messages.

ATK_ICMP_ADDRMASK_REQ

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ: IcmpType(1058)=17; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_RAW: IcmpType(1058)=17; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask request is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_RAW_SZ: IcmpType(1058)=17; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunn