LSUM1MPUS06XEC0 Card Manual-APW100

HomeSupportSwitchesS10500X SeriesInstall & UpgradeMPU Card ManualsLSUM1MPUS06XEC0 Card Manual-APW100
Download Book
  • Released At: 18-11-2019
  • Page Views:
  • Downloads:
Table of Contents
Related Documents

MPU - LSUM1MPUS06XEC0

1  Card identifier

The card identifier LSUM1MPUS06XEC0 is in the upper right corner of the front panel.

2  Specifications

IMPORTANT

IMPORTANT:

H3C recommends that you use only H3C-certified USB disks to ensure hardware reliability and compatibility.

 

Table 1 Card specifications

Item

Specifications

Flash

2 GB

BootROM

4 MB

NVRAM

1 MB

SDRAM (DDR4)

8 GB

Card size (H × W × D)

40 × 292 × 318 mm (1.57 × 11.50 × 12.52 in)

Power consumption

74 W to 135 W

Ports

·     1 console port

·     1 USB console port

·     4 network management ports: 2 RJ-45 ports and 2 SFP fiber ports

·     1 primary USB port

Port rate

·     Console port: 9600 bps to 115200 bps (default: 9600 bps)

·     USB console port: ≤ 115200 bps (default: 9600 bps)

·     network management ports ( RJ-45 ): 10/100/1000 Mbps, half/full duplex

·     network management ports  (SFP ): 1000 Mbps

Transmission medium and max transmission distance

·     Console port: 15 m (49.21 ft) over asynchronous EIA/TIA-232 cables

·     USB console port: 10 m (32.81 ft) over USB-AB cables

·     network management ports ( RJ-45 ): 100 m (328.08 ft) over Category 5 or higher twisted pair cables

·     network management ports  (SFP ): GE SFP fiber module specifications

Applicable hardware platforms

S10506X

Applicable host software versions

Release 7585 and later

 

 

NOTE:

·     The OFFLINE button on the MPU is intended for debugging and locating failures by technical supports. H3C recommends not using it without authorization.

·     H3C recommends not using a USB extender cable to connect the USB port.

 

The 10/100/1000BASE-T copper port uses an RJ-45 connector.

Figure 1 RJ-45 connector

 

Table 2 RJ-45 GE connector pinout

Pin

10BASE-T/100BASE-TX/1000BASE-T

Signal

Function

1

MX_0+

Transmits and receives data.

2

MX_0-

Transmits and receives data.

3

MX_1+

Transmits and receives data.

4

MX_2+

Transmits and receives data.

5

MX_2-

Transmits and receives data.

6

MX_1-

Transmits and receives data.

7

MX_3+

Transmits and receives data.

8

MX_3-

Transmits and receives data.

 

IMPORTANT

IMPORTANT:

For more information about transceiver modules and cables available for the card, see H3C S10500X Switch Series Cards and Transceiver Modules Compatibility Matrixes.

 

3  Related documentation

For module installation, see H3C S10500X Switch Series Installation Guide.

For software upgrade, see the release notes for the device.

 

 

Copyright © 2018 New H3C Technologies Co., Ltd.

The information in this document is subject to change without notice.

 

  • Cloud & AI
  • InterConnect
  • Intelligent Computing
  • Security
  • SMB Products
  • Intelligent Terminal Products
  • Product Support Services
  • Technical Service Solutions
All Services
  • Resource Center
  • Policy
  • Online Help
All Support
  • Become a Partner
  • Partner Resources
  • Partner Business Management
All Partners
  • Profile
  • News & Events
  • Online Exhibition Center
  • Contact Us
All About Us
新华三官网