LSUM1SUPXES0 Card Manual-APW100

HomeSupportResource CenterSwitchesH3C S10500X Switch SeriesH3C S10500X Switch SeriesTechnical DocumentsInstallCard Module ManualsLSUM1SUPXES0 Card Manual-APW100
Download Book
Title Size Downloads
LSUM1SUPXES0 Card Manual-APW100-book.pdf 69.24 KB
Table of Contents
Related Documents

MPU—LSUM1SUPXES0

1  Card identifier

The module identifier LSUM1SUPXES0 is in the upper right corner of the front panel.

2  Specifications

Table 1 Module specifications

Item

Specifications

Flash

4 GB

BootROM

32 MB

NVRAM

1 MB

SDRAM (DDR4)

8 GB

Card size (H × W × D)

40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)

Power consumption

28 W to 42 W

Ports

·     1 console port

·     1 USB console port

·     4 network management ports: 2 RJ-45 ports and 2 SFP fiber ports

·     1 primary USB port

·     2 × SMB coaxial clock output ports

·     2 × SMB coaxial clock input ports

·     2 × high-precision time synchronization ports

Transmission rate

·     Console port: 9600 bps to 115200 bps (default: 9600 bps)

·     USB console port: ≤ 115200 bps (default: 9600 bps)

·     network management ports (RJ-45): 10/100/1000 Mbps, half/full duplex

·     network management ports (SFP): 1000 Mbps

·     SMB coaxial clock input/output port: 2.048 Mbps

·     High-precision time synchronization port: 9600 bps

Transmission medium and max transmission distance

·     Console port: 15 m (49.21 ft) over asynchronous EIA/TIA-232 cables

·     USB console port: 10 m (32.81 ft) over USB-AB cables

·     network management ports (RJ-45): 100 m (328.08 ft) over Category 5 or higher twisted pair cables

·     network management ports (SFP): GE SFP fiber module specifications

·     SMB coaxial clock input/output port: 75 ohm coaxial cables

·     High-precision time synchronization port: Category 5 or higher twisted pair cables

Compatible device models

S10508X/S10508X-V/S10516X

Software version

Release 7595 and Later

 

 

NOTE:

H3C recommends not using a USB extender cable to connect the USB port.

 

The 10/100/1000BASE-T copper port uses an RJ-45 connector.

Figure 1 RJ-45 connector

 

Table 2 RJ-45 GE connector pinout

Pin

10BASE-T/100BASE-TX/1000BASE-T

Signal

Function

1

MX_0+

Transmits and receives data.

2

MX_0-

Transmits and receives data.

3

MX_1+

Transmits and receives data.

4

MX_2+

Transmits and receives data.

5

MX_2-

Transmits and receives data.

6

MX_1-

Transmits and receives data.

7

MX_3+

Transmits and receives data.

8

MX_3-

Transmits and receives data.

 

IMPORTANT

IMPORTANT:

For more information about transceiver modules and cables available for the card, see H3C S10500X Switch Series Cards and Transceiver Modules Compatibility Matrixes.

 

3  Related documentation

For module installation, see H3C S10500X Switch Series Installation Guide.

For software upgrade, see the release notes for the device.

 

 

Copyright © 2019 New H3C Technologies Co., Ltd.

The information in this document is subject to change without notice.