- Released At: 06-12-2022
- Page Views:
- Downloads:
- Table of Contents
- Related Documents
-
H3C CR-19K-MPU-16B main processing unit
1 Identifier
The module identifier CR-19K-MPU-16B is on the far right of the front panel.
2 About the MPU
The CR-19K-MPU-16B main processing unit (MPU) provides the following functionalities:
· Route calculation and forwarding table maintenance.
· System configuration, control, and monitoring. On the MPU, you can monitor, upgrade software, and reset a module.
· High-precision clock and time synchronization.
· Real-time clock (RTC) that keeps tracks of the current time, providing seconds, minutes, hours, day, date, month, and year information.
· Support for active/standby switchover when two MPUs are installed on the router.
IMPORTANT: If you install two MPUs for the router, make sure they are the same model. |
Figure 1 Front panel
(1) 1PPS/ToD time synchronization ports 1 and 2 |
(2) SMB clock output ports 1 and 2 |
(3) SMB clock input ports 1 and 2 |
(4) EXT ports and LEDs |
(5) Fan tray status LEDs |
(6) Module status LED |
(7) MPU active/standby status LED |
(8) Module identifier (CR-19K-MPU-16B) |
(9) Reset button |
(10) Hard disk status LED |
(11) System alarm LED |
(12) Power supply status LEDs |
(13) Console port (CONSOLE) |
(14) USB host port |
(15) Management port and LED (MANAGEMENT) |
(16) 1000BASE-X-SFP ports and LEDs 1 to 4 |
Table 1 MPU specifications
Item |
Specifications |
Processor |
Six-core @ 1.9 GHz |
DRAM size |
32 GB |
Dimensions (H × W × D) |
44 × 433 × 512 mm (1.73 × 17.05 × 20.16 in) |
Hard disk |
240 GB |
Power consumption |
200 W |
Hot swapping |
Supported |
Ports |
· 1 × console port · 1 × USB port (Type A, host mode) · 1 ×10/100/1000BASE-T management port · 4 × 1000BASE-X-SFP ports · EXT ports: ¡ 1 × 10/100/1000BASE-T RJ-45 BMC port ¡ ETH ports: 1 × 10/100/1000BASE-T port and 2 × 10GBASE-R-SFP+ ports ¡ 1 × USB port (Type A) · 2 × SMB clock input ports · 2 × SMB clock output ports · 2 × 1PPS/ToD time synchronization ports |
Interface transmission rate |
· Console port: 9600 (default) to 115200 bps · 10/100/1000BASE-T management port: 10/100/1000 Mbps · 1000BASE-X-SFP port: 1000 Mbps · 10/100/1000BASE-T RJ-45 BMC port: 10/100/1000 Mbps · ETH ports: ¡ 10/100/1000BASE-T port: 10/100/1000 Mbps ¡ 10GBASE-R-SFP+ port: 10 Gbps |
Compatible devices |
CR19000-16 |
IMPORTANT: · To verify compatibility of the MPU with the software release you are using, see the release notes. · For the transceiver modules and cables available for the MPU, see H3C CR19000 Core Routers Modules and Transceivers Compatibility Matrixes. |
Copyright © 2022 New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.