- Released At: 13-10-2022
- Page Views:
- Downloads:
- Table of Contents
- Related Documents
-
|
H3C CR16000-M Router Series |
Ethernet Interface Module Datasheet |
|
|
Copyright © 2022 New H3C Technologies Co., Ltd. All rights reserved.
No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New H3C Technologies Co., Ltd.
Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this document are the property of their respective owners.
The information in this document is subject to change without notice.
Overview
The following Ethernet interface modules are available for the CR16000-M routers.
Table 1 Ethernet interface modules available for the CR16000-M routers
Module model |
Description |
MIC-CQ1L-M |
1-port 100G Ethernet optical interface module |
MIC-CQ1LF-M |
1-port 100G flexible Ethernet optical interface module |
MIC-CQ2L-M |
2-port 100G Ethernet optical interface module |
MIC-GP12L-M |
12-port 1000BASE-X Ethernet optical interface module |
MIC-GP24L-M |
24-port 1000BASE-X Ethernet optical interface module |
MIC-GT12L-M |
12-port 1000BASE-T Ethernet copper interface module |
MIC-TCP8L-M |
8-port OC-3c/OC-12c (622M/155M) POS/GE optical interface module |
MIC-XP4L-M |
4-port 10GBASE-R Ethernet optical interface module |
MIC-XP10L-M |
10-port 10GBASE-R/W Ethernet optical interface module |
Key features
Layer 2/Layer 3 switching
There are two types of Ethernet interfaces:
· Layer 2 Ethernet interface—Operates at the data link layer and processes Layer 2 protocols for quick forwarding.
· Layer 3 Ethernet interface—Operates at the network layer and can be configured with an IP address. It processes Layer 3 protocols and provides the routing function.
Flexible configuration
LAN/WAN mode switching
The 10G interfaces provided by the interface modules support LAN and WAN modes. You can use the command line to configure a 10G port to operate in LAN or WAN mode. When operating in WAN mode, the 10G port can interconnect with a transmission device for long-haul transmission. For more information, see H3C CR16000-M Routers Interface Configuration Guides.
Port isolation
The port isolation function can isolate ports in the same VLAN from one another to provide more secure and flexible networking solutions.
Link aggregation
The link aggregation function allows you to aggregate multiple physical Ethernet ports into one logical aggregate interface. The upper-level entity using the link aggregation service regards the multiple physical links in the same aggregation port as one logical link.
10-GE and GE interface switching
The interface modules provide 10-GE interfaces. You can switch 10-GE interfaces to GE interfaces from the CLI if the peer end uses GE interfaces or if 10-GE transceiver modules are not available. You can switch the interfaces back to 10-GE for higher bandwidth. For more information, see H3C CR16000-M Routers Interface Configuration Guides.
Flexible Ethernet mode switching
The interfaces on the interface modules support switching between standard Ethernet mode and flexible Ethernet mode to meet different service requirements. For more information, see H3C CR16000-M Routers Interface Configuration Guides.
Super interface module
As a super interface module, the MIC-TCP8L-M interface module supports flexible configuration of POS and GE interfaces.
Specifications
The figures in this section are for illustration only.
MIC-CQ1L-M
Front panel
Figure 2 MIC-CQ1L-M front panel
(1) 100GBASE-R-QSFP28 fiber port (1 in total) |
(2) Module status LED (see Table 2 for the description) |
(3) QSFP28 port LED (see Table 7 for the description) |
Technical specifications
Item |
Specifications |
Dimensions (H × W × D) |
22 × 214 × 262 mm (0.87 × 8.43 × 10.32 in) |
Power consumption |
16 W to 18 W |
Ports |
1 × 100GBASE-R-QSFP28 fiber port |
Connector type |
LC |
Port speed |
100 Gbps |
MIC-CQ1LF-M
Front panel
Figure 4 MIC-CQ1LF-M front panel
(1) 100GBASE-R-QSFP28 fiber port (1 in total) |
(2) Module status LED (see Table 2 for the description) |
(3) QSFP28 port LED (see Table 7 for the description) |
Technical specifications
Item |
Specifications |
Dimensions (H × W × D) |
22 × 214 × 262 mm (0.87 × 8.43 × 10.32 in) |
Power consumption |
38 W to 50 W |
Ports |
1 × 100GBASE-R-QSFP28 fiber port |
Connector type |
LC |
Port speed |
100 Gbps |
MIC-CQ2L-M
Figure 5 MIC-CQ2L-M
Front panel
Figure 6 MIC-CQ2L-M front panel
(1) 100GBASE-R-QSFP28 fiber ports (2 in total) |
(2) Module status LED (see Table 2 for the description) |
(3) QSFP28 port LED (see Table 7 for the description) |
Technical specifications
Item |
Specifications |
Dimensions (H × W × D) |
22 × 214 × 262 mm (0.87 × 8.43 × 10.32 in) |
Power consumption |
26 W to 28 W |
Ports |
2 × 100GBASE-R-QSFP28 fiber ports |
Connector type |
LC |
Port speed |
100 Gbps |
MIC-GP12L-M
Figure 7 MIC-GP12L-M
Front panel
Figure 8 MIC-GP12L-M front panel
(1) 1000BASE-X-SFP fiber ports (12 in total) |
(2) Module status LED (see Table 2 for the description) |
(3) SFP port LED (see Table 5 for the description) |
Technical specifications
Item |
Specifications |
Dimensions (H × W × D) |
22 × 214 × 262 mm (0.87 × 8.43 × 10.32 in) |
Power consumption |
36 W to 38 W |
Ports |
12 × 1000BASE-X-SFP fiber ports |
Connector type |
LC |
Port speed |
· 10 Mbps · 100 Mbps · 1000 Mbps |
MIC-GP24L-M
Figure 9 MIC-GP24L-M
Front panel
Figure 10 MIC-GP24L-M front panel
(1) 1000BASE-X-SFP fiber ports (24 in total) |
(2) Module status LED (see Table 2 for the description) |
(3) SFP port LED (see Table 5 for the description) |
Technical specifications
Item |
Specifications |
Dimensions (H × W × D) |
44 × 214 × 262 mm (1.73 × 8.43 × 10.32 in) |
Power consumption |
29 W to 42 W |
Ports |
24 × 1000BASE-X-SFP fiber ports |
Connector type |
LC |
Port speed |
· 10 Mbps · 100 Mbps · 1000 Mbps |
MIC-GT12L-M
Figure 11 MIC-GT12L-M
Front panel
Figure 12 MIC-GT12L-M front panel
(1) RJ-45 Ethernet port LED (see Table 4 for the description) |
|
(2) 1000BASE-X-SFP fiber ports (12 in total) |
(3) Module status LED (see Table 2 for the description) |
Technical specifications
Item |
Specifications |
Dimensions (H × W × D) |
22 × 214 × 262 mm (0.87 × 8.43 × 10.32 in) |
Power consumption |
30 W to 32 W |
Ports |
12 × 1000BASE-T copper ports |
Connector type |
RJ45 |
Port speed |
· 10 Mbps · 100 Mbps · 1000 Mbps |
MIC-TCP8L-M
Figure 13 MIC-TCP8L-M
Front panel
Figure 14 MIC-TCP8L-M front panel
(1) OC-3c/OC-12c POS/GE fiber ports (8 in total) |
(2) Module status LED (see Table 2 for the description) |
(3) Port LED (see Table 3 for the description) |
Technical specifications
Item |
Specifications |
Dimensions (H × W × D) |
22 × 214 × 262 mm (0.87 × 8.43 × 10.32 in) |
Power consumption |
43 W to 45 W |
Ports |
8 × OC-3c/STM-1c, OC-12c/STM-4c, or 1000BASE-X-SFP POS/GE fiber ports |
Connector type |
LC |
Port speed |
· 155 Mbps (OC-3c/STM-1c) · 622 Mbps (OC-12c/STM-4c) · 1000 Mbps |
MIC-XP4L-M
Figure 15 MIC-XP4L-M
Front panel
Figure 16 MIC-XP4L-M front panel
(1) 10GBASE-R/W-SFP+ fiber ports (4 in total) |
(2) Module status LED (see Table 2 for the description) |
(3) SFP+ port LED (see Table 6 for the description) |
Technical specifications
Item |
Specifications |
Dimensions (H × W × D) |
22 × 214 × 262 mm (0.87 × 8.43 × 10.32 in) |
Power consumption |
14 W to 16 W |
Ports |
4 × 10GBASE-R-SFP+ fiber ports |
Connector type |
LC |
Port speed |
10 Gbps |
MIC-XP10L-M
Figure 17 MIC-XP10L-M
Front panel
Figure 18 MIC-XP10L-M front panel
(1) 10GBASE-R/W-SFP+ fiber ports (10 in total) |
(2) Module status LED (see Table 2 for the description) |
(3) SFP+ port LED (see Table 6 for the description) |
Technical specifications
Item |
Specifications |
Dimensions (H × W × D) |
22 × 214 × 262 mm (0.87 × 8.43 × 10.32 in) |
Power consumption |
35 W to 50 W |
Ports |
10 × 10GBASE-R-SFP+ fiber ports, supporting the WAN mode |
Connector type |
LC |
Port speed |
· 1000 Mbps · 10 Gbps |
LEDs
Table 2 Module status LED description
Mark |
Status |
Description |
RUN |
Flashing at 0.5 Hz |
The interface module is operating correctly. |
Fast flashing at 4 Hz |
The interface module is loading software. If the LED keeps flashing fast, software loading fails. |
|
On |
The interface module is faulty. |
|
Off |
The interface module is faulty or is not powered on. |
Table 3 ACT/ALM port LED description
Mark |
Status |
Description |
ACT/ALM |
Flashing green |
The port is sending or receiving data. |
Steady green |
A link is present. |
|
Steady red |
An alarm has occurred. |
|
Off |
No link is present. |
Table 4 RJ-45 Ethernet port LED description
Status |
Description |
Flashing |
The port is sending or receiving data. |
Steady on |
A link is present. |
Off |
No link is present. |
Table 5 SFP port LED description
Status |
Description |
Flashing |
The port is sending or receiving data. |
Steady on |
A link is present. |
Off |
No link is present. |
Table 6 SFP+ port LED description
Status |
Description |
Flashing |
The port is sending or receiving data. |
Steady on |
A link is present. |
Off |
No link is present. |
|
NOTE: An SFP+ port LED indicates the port operating rate by color. When the LED is green, the port is operating at 10 Gbps. When the port is yellow, the port is operating at 1000 Mbps. |
Table 7 QSFP28 port LED description
Status |
Description |
Flashing |
The port is sending or receiving data. |
Steady on |
A link is present. |
Off |
No link is present. |
|
NOTE: A QSFP28 port indicates the port operating rate by color. When the LED is green, the port is operating at 100 Gbps. |
Environment requirements
Make sure the ambient environment meets the following requirements:
· Temperature and humidity requirements
Table 8 Temperature and humidity requirements
Item |
Specifications |
Operating temperature |
0°C to 45°C (32°F to 113°F) |
Storage temperature |
–40°C to +70°C (–40°F to +158°F) |
Operating humidity |
5% RH to 95% RH, non-condensing |
Storage humidity |
5% RH to 95% RH, non-condensing |
· Dust protection requirements
Table 9 Dust concentration limits in the equipment room
Substance |
Particle diameter |
Concentration limit |
Dust particles |
≥ 0.5 µm |
≤ 1.8 × 107 particles/m3 |
· Corrosive gas protection requirements
Table 10 Corrosive gas concentration limits in the equipment room
Gas |
Average concentration (mg/m3) |
Maximum concentration (mg/m3) |
SO2 |
0.3 |
1.0 |
H2S |
0.1 |
0.5 |
Cl2 |
0.1 |
0.3 |
HCI |
0.1 |
0.5 |
HF |
0.01 |
0.03 |
NH3 |
1.0 |
3.0 |
O3 |
0.05 |
0.1 |
NOX |
0.5 |
1.0 |