- Released At: 12-12-2022
- Page Views:
- Downloads:
- Table of Contents
- Related Documents
-
|
H3C CR16000-F Router Series |
CPOS Subcard Datasheet |
|
|
Copyright © 2015 to 2022 New H3C Technologies Co., Ltd. All rights reserved.
No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New H3C Technologies Co., Ltd.
Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this document are the property of their respective owners.
The information in this document is subject to change without notice.
Contents
Overview
The following CPOS subcards are available for the CR16000-F routers.
Table 1 CPOS subcards available for the CR16000-F routers
Card model |
Description |
MIC-CLP2L |
2-port OC-3/STM-1 channelized POS optical interface card (SFP, LC) |
MIC-CLP4L |
4-port OC-3/STM-1 channelized POS optical interface card (SFP, LC) |
Key features
Bandwidth channelization
MP-group supported
The CPOS interface supports multilink PPP group (MP-Group). An MP-group can be used as a logical interface to carry the traffic of various services, providing multiple options for bandwidth and line selection.
Specifications
The figures in this section are for illustration only.
MIC-CLP2L
Figure 1 MIC-CLP2L
Front panel
Figure 2 MIC-CLP2L front panel
(1) CPOS-OC3/STM1-SFP fiber ports (2 in total) |
(2) Port status LED |
Technical specifications
Item |
Specifications |
Dimensions (H × W × D) |
18 × 165 × 142 mm (0.71 × 6.50 × 5.59 in) |
Power consumption |
9.8 W to 10.9 W |
Ports |
2 NOTE: You can configure a fiber port as an OC-3/STM-1 CPOS or OC-3c/STM-1c POS fiber port at the CLI. By default, the port is an OC-3/STM-1 CPOS fiber port. |
Connector type |
SFP/LC |
Port speed |
OC-3/STM-1 |
MIC-CLP4L
Figure 3 MIC-CLP4L
Front panel
Figure 4 MIC-CLP4L front panel
(1) CPOS-OC3/STM1-SFP fiber ports (4 in total) |
(2) Port status LED |
Technical specifications
Item |
Specifications |
Dimensions (H × W × D) |
18 × 165 × 142 mm (0.71 × 6.50 × 5.59 in) |
Power consumption |
9.8 W to 12.9 W |
Ports |
4 NOTE: You can configure the fiber port as an OC-3/STM-1 CPOS or OC-3c/STM-1c POS fiber port at the CLI. By default, the port is an OC-3/STM-1 CPOS fiber port. |
Connector type |
SFP/LC |
Port speed |
OC-3/STM-1 |
LEDs
Table 2 SFP port status LED description
Status |
Description |
Flashing green |
The port is sending or receiving data. |
Steady green |
A link is present. |
Steady red |
An alarm has occurred. |
Off |
No link is present. |
Environment requirements
Make sure the ambient environment meets the following requirements:
· Temperature and humidity requirements
Table 3 Temperature and humidity requirements
Item |
Specifications |
Operating temperature |
0°C to 45°C (32°F to 113°F) |
Storage temperature |
–40°C to +70°C (–40°F to +158°F) |
Operating humidity |
10% RH to 95% RH, non-condensing |
Storage humidity |
5% RH to 95% RH, non-condensing |
· Dust protection requirements
Table 4 Dust concentration limits in the equipment room
Substance |
Particle diameter |
Concentration limit |
Dust particles |
≥ 0.5 µm |
≤ 1.8 × 107 particles/m3 |
· Corrosive gas protection requirements
Table 5 Corrosive gas concentration limits in the equipment room
Gas |
Average concentration (mg/m3) |
Maximum concentration (mg/m3) |
SO2 |
0.3 |
1.0 |
H2S |
0.1 |
0.5 |
Cl2 |
0.1 |
0.3 |
HCI |
0.1 |
0.5 |
HF |
0.01 |
0.03 |
NH3 |
1.0 |
3.0 |
O3 |
0.05 |
0.1 |
NOX |
0.5 |
1.0 |