H3C CR16000-F Routers CMPE Base Card Datasheet-5W103

HomeSupportRoutersCR16000-F SeriesProduct LiteratureCard DatasheetsH3C CR16000-F Routers CMPE Base Card Datasheet-5W103
Download Book
  • Released At: 12-12-2022
  • Page Views:
  • Downloads:
Table of Contents
Related Documents

H3C CR16000-F Router Series

CMPE Base Card Datasheet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Copyright © 2015 to 2022 New H3C Technologies Co., Ltd. All rights reserved.

No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New H3C Technologies Co., Ltd.

Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this document are the property of their respective owners.

The information in this document is subject to change without notice.



Overview

The following CMPE base cards are available for the CR16000-F routers.

Table 1 CMPE base cards available for the CR16000-F routers

Card model

Description

CMPE-1104

4-port multiservice processing engine, support for four MIC subcards

 

 

NOTE:

For compatibility between CMPE base cards and switching fabric modules, see Appendix B FRUs and compatibility matrixes in H3C CR16000-F Routers Installation Guide.

 

Key features

High performance and scalability

Based on the 40G hardware platform, the CMPE card delivers the following benefits:

·     Flexible and efficient service scalability.

·     High-performance service processing and forwarding capability.

Dual forwarding engines

The CMPE card uses the ASIC-based and NP-based forwarding engines to improve forwarding performance and QoS scheduling efficiency.

Distributed OAM engine

The distributed OAM engine improves BFD efficiency, simplifies CMPE card architecture, and enhances OAM system performance.

200 ms of packet buffering

The card can provide 200 ms of packet buffering, which enables 100% egress bandwidth usage and improves network performance.

Removable interface cards

Interface cards are not fixed on the base card but removable from the base card. You can install different interface cards on the base card to adapt to different configuration requirements, which protects user investment.

Subcard hot swapping

The base card supports hot swapping of subcards. Installing and removing a subcard on an operating router do not affect ongoing services on other subcards.

Distributed NAT

With support for distributed NAT architecture, twice NAT, and multiple-instance NAT instances, the cards can share NAT loads to improve NAT performance.

Distributed NetStream

With distributed NetStream performed on each card, the card can greatly improve statistical analysis efficiency. In addition, it offers packet filtering, packet sampling, statistics aggregation, and statistics export to improve processing efficiency.

Distributed NAT-PT

The distributed NAT-PT architecture allows CMPE cards to share NAT-PT loads to improve NAT-PT performance.

TDM simulation

The CMPE card uses TDM to transmit multiple signals or data streams on one link.

Specifications

The figures in this section are for illustration only.

Figure 1 CMPE-1104

 

Front panel

Figure 2 CMPE-1104 front panel

(1) Status LED

 

Technical specifications

Item

Specifications

Dimensions (H × W × D)

40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)

Power consumption

91 W to 158 W

Net weight

3.52 kg (7.76 lb)

Subslots

4

Applicable system software versions

7133 or later

 

The CMPE-1104 does not support the MIC-GP10L1. Subslots 3 and 4 on the CMPE-1104 do not support the MIC-GP8L or MIC-SP8L.

If the MIC-SP8L is installed in subslot 1 or 2, only the MIC-CLP2L or MIC-ET16L can be installed in subslots 3 and 4. If the MIC-CLP2L or MIC-ET16L is not installed in subslot 3 or 4, the MIC-SP8L cannot be installed in subslot 1 or 2.

 

 

NOTE:

The maximum power consumption of the CMPE-1104 card refers to the power usage when the card is fully configured with subcards that have the highest power consumption.

 

LEDs

Table 2 Status LED description

LED mark

Status

Description

RUN

Steady green

The card is faulty.

Off

The card is faulty or not installed.

Flashing green (1 Hz)

The card is operating correctly.

Fast flashing green

The card is starting up. If the LED keeps fast flashing, the card registration has failed.

 

Environment requirements

Make sure the ambient environment meets the following requirements:

·     Temperature and humidity requirements

Table 3 Temperature and humidity requirements

Item

Specifications

Operating temperature

0°C to 45°C (32°F to 113°F)

Storage temperature

–40°C to +70°C (–40°F to +158°F)

Operating humidity

10% RH to 95% RH, non-condensing

Storage humidity

5% RH to 95% RH, non-condensing

 

·     Dust protection requirements

Table 4 Dust concentration limits in the equipment room

Substance

Particle diameter

Concentration limit

Dust particles

≥ 0.5 µm

≤ 1.8 × 107 particles/m3

 

·     Corrosive gas protection requirements

Table 5 Corrosive gas concentration limits in the equipment room

Gas

Average concentration (mg/m3)

Maximum concentration (mg/m3)

SO2

0.3

1.0

H2S

0.1

0.5

Cl2

0.1

0.3

HCI

0.1

0.5

HF

0.01

0.03

NH3

1.0

3.0

O3

0.05

0.1

NOX

0.5

1.0

 

  • Cloud & AI
  • InterConnect
  • Intelligent Computing
  • Security
  • SMB Products
  • Intelligent Terminal Products
  • Product Support Services
  • Technical Service Solutions
All Services
  • Resource Center
  • Policy
  • Online Help
All Support
  • Become a Partner
  • Partner Resources
  • Partner Business Management
All Partners
  • Profile
  • News & Events
  • Online Exhibition Center
  • Contact Us
All About Us
新华三官网