05-WLAN Access Command Reference

HomeSupportResource CenterH3C FAT AP Command References(R5436)-6W10105-WLAN Access Command Reference
01-WLAN access commands
Title Size Download
01-WLAN access commands 365.09 KB

Contents

WLAN access commands· 1

access-control acl 1

beacon ssid-hide· 2

client cache aging-time· 3

client max-count 3

client smart-access enable· 4

client-mode access-retransmit 5

client-mode authentication-method· 5

client-mode beacon-keepalive· 6

client-mode cipher-suite· 7

client-mode connect 8

client-mode disconnect 9

client-mode enable· 9

client-mode link-hold-rssi 10

client-mode min-record-rssi 10

client-mode probe-keepalive· 11

client-mode roam·· 12

client-mode roam calibration-interval 13

client-mode roam rssi-threshold· 13

client-mode roam scan-aging· 14

client-mode roam scan-interval 15

client-mode roam-enhance· 16

client-mode ssid· 17

client-mode vlan· 17

customlog format wlan· 18

description· 19

display interface wlan-radio· 19

display wlan ap all client-number 22

display wlan ap all radio client-number 23

display wlan blacklist 23

display wlan bss· 24

display wlan client 25

display wlan client ipv6· 32

display wlan client online-duration· 32

display wlan client status· 33

display wlan client-mode packet-statistics· 35

display wlan client-mode radio· 36

display wlan client-mode roam-enhance bss· 38

display wlan client-mode roaming-state· 39

display wlan client-mode ssid· 41

display wlan service-template· 42

display wlan statistics client 47

display wlan statistics connect-history· 48

display wlan statistics service template· 48

display wlan whitelist 49

interface wlan-radio· 50

nas-id· 50

nas-port-type· 51

quick-association enable· 52

reset wlan client 52

reset wlan client-mode packet-statistics· 53

reset wlan client-mode roaming-state· 53

reset wlan dynamic-blacklist 54

reset wlan statistics client 54

reset wlan statistics service-template· 55

service-template· 55

service-template enable· 56

snmp-agent trap enable wlan client 56

snmp-agent trap enable wlan client-audit 57

ssid· 57

unknown-client 58

vlan· 59

wlan association optimization· 59

wlan broadcast-probe reply· 60

wlan client idle-timeout 60

wlan client keep-alive· 61

wlan client keep-alive interval 62

wlan client reauthentication-period· 62

wlan dynamic-blacklist lifetime· 63

wlan link-test 64

wlan nas-port-id format 66

wlan service-template· 66

wlan static-blacklist mac-address· 67

wlan web-server api-path· 68

wlan web-server host 68

wlan web-server max-client-entry· 69

wlan whitelist mac-address· 70

 


WLAN access commands

The WA6600 series does not support the client mode or the following client mode-related commands:

·     client-mode access-retransmit

·     client-mode authentication-method

·     client-mode beacon-keepalive

·     client-mode cipher-suite

·     client-mode connect

·     client-mode disconnect

·     client-mode enable

·     client-mode link-hold-rssi

·     client-mode min-record-rssi

·     client-mode probe-keepalive

·     client-mode roam

·     client-mode roam calibration-interval

·     client-mode roam rssi-threshold

·     client-mode roam scan-aging

·     client-mode roam scan-interval

·     client-mode roam-enhance

·     client-mode ssid

·     client-mode vlan

·     display wlan client-mode packet-statistics radio radio-id

·     display wlan client-mode radio

·     display wlan client-mode roam-enhance bss

·     display wlan client-mode roaming-state

·     display wlan client-mode ssid [ ssid ]

·     reset wlan client-mode packet-statistics radio radio-id

·     reset wlan client-mode roaming-state

access-control acl

Use access-control acl to specify an ACL for ACL-based access control.

Use undo access-control acl to restore the default.

Syntax

access-control acl acl-number

undo access-control acl

Default

No ACL is specified.

Views

Service template view

Predefined user roles

network-admin

Parameters

acl-number: Specifies the number of a Layer 2 ACL, in the range of 4000 to 4999.

Usage guidelines

This feature controls client access by using the specified ACL rules. When the device receives an association request, it performs the following actions:

·     Allows the client to access the WLAN if the MAC address of the client matches the MAC address attribute or MAC address OUI attribute in a rule and the rule action is permit. If multiple clients match the OUI attribute, all these clients are allowed to access the WLAN.

·     Denies the client's access to the WLAN if no match is found or the matched rule has a deny statement.

When you configure this feature, follow these restrictions and guidelines:

·     If the specified ACL contains a deny statement, configure a permit statement for the ACL to permit all clients. If you do not do so, no clients can come online.

·     ACL-based access control configuration takes precedence over whitelist and blacklist configuration.

·     You can specify only one ACL. If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Create ACL 4000 and create ACL rules to permit the client with MAC address 000e-35b2-000e and clients with the specified OUI. Specify ACL 4000 for service template service1.

<Sysname> system-view

[Sysname] acl mac 4000

[Sysname-acl-mac-4000] rule 0 permit source-mac 000e-35b2-000e ffff-ffff-ffff

[Sysname-acl-mac-4000] rule 1 permit source-mac 000e-35b2-000f ffff-ff00-0000

[Sysname-acl-mac-4000] rule 2 deny

[Sysname-acl-mac-4000] quit

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] access-control acl 4000

beacon ssid-hide

Use beacon ssid-hide to disable advertising of the Service Set Identifier (SSID) in beacon frames.

Use undo beacon ssid-hide to restore the default.

Syntax

beacon ssid-hide

undo beacon ssid-hide

Default

The SSID is advertised in beacon frames.

Views

Service template view

Predefined user roles

network-admin

Usage guidelines

This command disables a radio from carrying SSIDs in the beacon frames and responding to probe requests after the specified service template is bound to the radio.

Examples

# Disable advertising the SSID in beacon frames.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] beacon ssid-hide

client cache aging-time

Use client cache aging-time to set the aging time for the cache of clients.

Use undo client cache aging-time to restore the default.

Syntax

client cache aging-time aging-time

undo client cache aging-time

Default

The aging time for the cache of clients is 180 seconds.

Views

Service template view

Predefined user roles

network-admin

Parameters

aging-time: Specifies the aging time for the cache of clients, in the range of 0 to 86400 seconds.

Usage guidelines

If you set the aging time to 0 seconds, the AC clears the client cache immediately when the clients go offline.

Make sure the service template is disabled before you execute this command.

Examples

# Set the aging time for the cache of clients to 100 seconds.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] client cache aging-time 100

client max-count

Use client max-count to set the maximum number of associated clients for a service template.

Use undo client max-count to restore the default.

Syntax

client max-count max-number

undo client max-count

Default

The number of associated clients for a service template is not limited.

Views

Service template view

Predefined user roles

network-admin

Parameters

max-number: Specifies the maximum number of clients in the range of 1 to 512.

Usage guidelines

With this feature configured, new clients cannot access the WLAN from a radio and the SSID is hidden when the maximum number is reached on the radio.

Examples

# Set the maximum number of associated clients to 38 for service template service1.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] client max-count 38

Related commands

beacon ssid-hide

client smart-access enable

Use client smart-access enable to enable smart client access.

Use undo client smart-access enable to restore the default.

Syntax

client smart-access enable

undo client smart-access enable

Default

Smart client access is disabled.

Views

Service template view

Predefined user roles

network-admin

Usage guidelines

This feature enables H3C wireless clients to access the WLAN automatically when the AKM mode is set to PSK or when the radio is bound to an empty service template.

Examples

# Enable smart client access.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] client smart-access enable

client-mode access-retransmit

Use client-mode access-retransmit to set the retransmission interval and maximum number of retransmission attempts for authentication and association requests.

Use undo client-mode access-retransmit to restore the default.

Syntax

client-mode access-retransmit interval interval [ count count ]

undo client-mode access-retransmit

Default

The retransmission interval is 300 milliseconds and the AP does not retransmit authentication and association requests.

Views

Radio interface view

Predefined user roles

network-admin

Parameters

interval: Specifies the retransmission interval in the range of 100 to 5000 milliseconds.

count: Specifies the maximum number of retransmission attempts, in the range of 1 to 10.

Usage guidelines

If the AP fails to receive any authentication or association response within the retransmission interval after the last retransmission, the AP tries to associate with another radio.

Make sure the client mode is enabled on the interface before you perform this task. Disabling the client mode removes the retransmission configuration.

Examples

# Set the retransmission interval to 500 ms and the maximum number of retransmission attempts to 3 for authentication and association requests.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] client-mode access-retransmit interval 500 count 3

Related commands

client-mode enable

client-mode authentication-method

Use client-mode authentication-method to specify the authentication method for a client-mode AP.

Use undo client-mode authentication-method to restore the default.

Syntax

client-mode authentication-method { open-system | shared-key | wpa2-psk }

undo client-mode authentication-method

Default

The authentication method for a client-mode AP is open-system.

Views

Radio interface view

Predefined user roles

network-admin

Parameters

open-system: Specifies open-system authentication.

shared-key: Specifies shared-key authentication.

wpa2-psk: Specifies WPA2-PSK authentication.

Usage guidelines

Make sure the client mode is enabled before you execute this command. Disabling the client mode removes the configuration.

Specify the CCMP or TKIP cipher suite when WPA2-PSK authentication is configured.

For the client-mode AP to access a WLAN, make sure the RSN IE and PSK AKM mode are configured for the WLAN if the authentication method is WPA2-PSK.

Examples

# Set the authentication method to shared-key.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] client-mode authentication-method shared-key

Related commands

client-mode cipher-suite

client-mode enable

client-mode beacon-keepalive

Use client-mode beacon-keepalive to enable beacon-based AP keepalive.

Use undo client-mode beacon-keepalive to disable beacon-based AP keepalive.

Syntax

client-mode beacon-keepalive interval interval count count

undo client-mode beacon-keepalive

Default

Beacon-based AP keepalive is disabled.

Views

Radio interface view

Predefined user roles

network-admin

Parameters

interval: Specifies the keepalive interval, in the range of 100 to 8191 milliseconds.

count: Specifies the keepalive count in the range of 1 to 100.

Usage guidelines

This feature enables the AP to proactively connect to another radio if the AP fails to receive any beacon frame from the currently associated radio before the beacon keepalive timer expires.

The beacon keepalive time equals the keepalive interval multiplied by the keepalive count.

Make sure the client mode has been enabled on the interface before you perform this task. Disabling the client mode removes the keepalive configuration.

As a best practice, set the beacon-based AP keepalive interval to a value twice the beacon sending interval or higher.

Examples

# Enable beacon-based AP keepalive, set the keepalive interval to 100 milliseconds, and set the keepalive count to 5.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] client-mode beacon-keepalive interval 100 count 5

Related commands

client-mode enable

client-mode cipher-suite

Use client-mode cipher-suite to specify the cipher suite and the pre-shared key for a client-mode AP.

Use undo client-mode cipher-suite to restore the default.

Syntax

client-mode cipher-suite { ccmp | tkip | { wep40 | wep104 | wep128 } [ key-id key-id ] } key [ cipher | simple ] string

undo client-mode cipher-suite

Default

No cipher suite and pre-shared key are configured for a client-mode AP.

Views

Radio interface view

Predefined user roles

network-admin

Parameters

ccmp: Specifies the AES-CCMP cipher suite.

tkip: Specifies the TKIP cipher suite.

wep40: Specifies the WEP40 cipher suite.

wep104: Specifies the WEP104 cipher suite.

wep128: Specifies the WEP128 cipher suite.

key-id key-id: Specifies the key ID in the range of 1 to 4. The default value is 1.

cipher: Sets a key in encrypted form.

simple: Sets a key in plaintext form. For security purposes, the key specified in plaintext form will be stored in encrypted form.

string: Specifies a key string. This argument is case sensitive. The key length varies by key type.

·     CCMP and TKIP—Its plaintext form is 8 to 63 characters. Its encrypted form is 8 to 117 characters.

·     WEP40—Its plaintext form is 5 characters. Its encrypted form is 37 to 73 characters.

·     WEP104—Its plaintext form is 13 characters. Its encrypted form is 37 to 73 characters.

·     WEP128—Its plaintext form is 16 characters. Its encrypted form is 37 to 73 characters.

Usage guidelines

Make sure the client mode is enabled before you execute this command. Disabling the client mode removes the configuration.

Examples

# Set the CCMP cipher suite, and configure simple character string 12345678 as the pre-shared key.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] client-mode cipher-suite ccmp key simple 12345678

Related commands

client-mode enable

client-mode connect

Use client-mode connect to connect a client-mode AP to the WLAN.

Syntax

client-mode connect

Views

Radio interface view

Predefined user roles

network-admin

Usage guidelines

Make sure the client mode is enabled and the SSID to associate with is specified before you execute this command.

After you use the client-mode disconnect command to disconnect a client-mode AP from the WLAN, you can use this command to reconnect the client-mode AP to the WLAN.

Examples

# Connect the client-mode AP to the WLAN.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] client-mode ssid service1

[Sysname-WLAN-Radio1/0/1] client-mode connect

Related commands

client-mode disconnect

client-mode enable

client-mode disconnect

Use client-mode disconnect to disconnect a client-mode AP from the WLAN.

Syntax

client-mode disconnect

Views

Radio interface view

Predefined user roles

network-admin

Usage guidelines

Make sure the client mode is enabled before you execute the command.

Examples

# Disconnect the client-mode AP from the WLAN.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] client-mode disconnect

Related commands

client-mode connect

client-mode enable

client-mode enable

CAUTION

CAUTION:

Do not configure wireless access services or WDS services on a radio interface with the client mode enabled.

Use client-mode enable to enable the client mode.

Use undo client-mode enable to disable the client mode.

Syntax

client-mode enable

undo client-mode enable

Default

The client mode is disabled.

Views

Radio interface view

Predefined user roles

network-admin

Usage guidelines

Make sure the client mode is enabled before you configure client mode settings.

A radio interface with the client mode enabled cannot provide wireless access services or WDS services.

Disabling the client mode removes all client mode configuration.

Examples

# Enable the client mode.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] client-mode enable

client-mode link-hold-rssi

Use client-mode link-hold-rssi to set the link hold RSSI for the current link.

Use undo client-mode link-hold-rssi to restore the default.

Syntax

client-mode link-hold-rssi rssi

undo client-mode link-hold-rssi

Default

The link hold RSSI for the current link is 0.

Views

Radio interface view

Predefined user roles

network-admin

Parameters

rssi: Specifies the link hold RSSI in the range of 0 to 100. Setting the interval to 0 disables the AP from proactively switching to another link because of low RSSI.

Usage guidelines

Perform this task to set the minimum RSSI for the current link to be retained. If the current link's RSSI drops below the link hold RSSI, the AP goes offline and then comes online from another radio.

Make sure the client mode has been enabled on the interface before you perform this task.

Examples

# Set the link hold RSSI for the current link to 18.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] client-mode link-hold-rssi 18

Related commands

client-mode enable

client-mode min-record-rssi

Use client-mode min-record-rssi to set the minimum RSSI threshold for BSS recording.

Use undo client-mode min-record-rssi to restore the default.

Syntax

client-mode link-hold-rssi rssi

undo client-mode link-hold-rssi

Default

The minimum RSSI threshold for BSS recording is 15.

Views

Radio interface view

Predefined user roles

network-admin

Parameters

rssi: Specifies the minimum RSSI threshold for BSS recording, in the range of 0 to 100.

Usage guidelines

Perform this task to set the minimum RSSI of a BSS that can be recorded. For a BSS that has been recorded, the AP determines that the BSS is not detected if the detected RSSI of the BSS does not reach the minimum threshold.

If roaming enhancement is disabled, you can set the threshold only on the radio enabled with the client mode. Disabling the client mode removes the threshold configuration.

If roaming enhancement is enabled, you can set the threshold only on the radio enabled with roaming enhancement. Disabling roaming enhancement removes the threshold configuration.

Examples

# Set the minimum RSSI threshold for BSS recording to 20.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] client-mode min-record-rssi 20

Related commands

client-mode enable

client-mode probe-keepalive

Use client-mode probe-keepalive to enable probe response-based AP keepalive.

Use undo client-mode probe-keepalive to disable probe response-based AP keepalive.

Syntax

client-mode probe-keepalive [ interval interval retry retries ]

undo client-mode probe-keepalive

Default

Probe response-based AP keepalive is enabled, the keepalive interval is 1000 milliseconds, and the maximum number of retransmission attempts is 5.

Views

Radio interface view

Predefined user roles

network-admin

Parameters

interval interval: Specifies the keepalive interval at which the AP sends probe requests, in the range of 100 to 60000 milliseconds. The default value is 1000.

retry retries: Specifies the maximum number of retransmission count, in the range of 1 to 100. The default value is 5.

Usage guidelines

This feature enables the AP to proactively connect to another radio if no probe response is received from the currently associated radio before the maximum number of probe request retransmission attempts is reached.

Make sure the client mode has been enabled on the interface before you perform this task. Disabling the client mode removes the keepalive configuration.

Examples

# Enable probe response-based AP keepalive, set the keepalive interval to 100 milliseconds, and set the maximum number of retransmission attempts to 5.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] client-mode probe-keepalive interval 100 retry 5

Related commands

client-mode enable

client-mode roam

Use client-mode roam to enable auto roaming for a client-mode AP to roam between wireless services in an ESS.

Use undo client-mode roam to restore the default.

Syntax

client-mode roam { quick | slow }

undo client-mode roam

Default

The auto roaming feature is disabled for a client-mode AP.

Views

Radio interface view

Predefined user roles

network-admin

Parameters

quick: Specifies quick roaming.

slow: Specifies slow roaming.

Usage guidelines

Make sure the client mode is enabled before you execute this command. Disabling the client mode removes the configuration.

Examples

# Enable quick auto roaming for the client-mode AP.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] client-mode roam quick

Related commands

client-mode enable

client-mode roam rssi-threshold

client-mode roam calibration-interval

Use client-mode roam calibration-interval to set the roaming calibration interval.

Use undo client-mode roam calibration-interval to restore the default.

Syntax

client-mode roam calibration-interval interval

undo client-mode roam calibration-interval

Default

The roaming calibration interval is 1000 milliseconds.

Views

Radio interface view

Predefined user roles

network-admin

Parameters

interval: Specifies the roaming calibration interval in the range of 1000 to 10000 milliseconds.

Usage guidelines

Perform this task to set the interval at which the AP triggers a roaming calibration. A short interval might result in frequent roaming, affecting network stability. A long interval might prevent the AP from switching to the optimal WLAN in time, affecting communication quality.

Make sure the client mode has been enabled on the interface before you perform this task. Disabling the client mode removes the interval configuration.

Examples

# Set the roaming calibration interval to 1000 milliseconds.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] client-mode roam calibration-interval 1000

Related commands

client-mode enable

client-mode roam rssi-threshold

Use client-mode roam rssi-threshold to set the roaming RSSI threshold and gap threshold.

Use undo client-mode roam rssi-threshold to restore the default.

Syntax

client-mode roam rssi-threshold rssi-value [ gap gap-value ]

undo client-mode roam rssi-threshold

Default

Both the roaming RSSI threshold and gap threshold are 20.

Views

Radio interface view

Predefined user roles

network-admin

Parameters

rssi-value: Specifies the RSSI threshold in the range of 10 to 50.

gap gap-value: Specifies the gap threshold in the range of 1 to 50.

Usage guidelines

Client-mode APs support the following roaming modes:

·     Quick roaming—An AP performs roaming when the RSSI gap between an optimal wireless service and the current wireless service exceeds the gap threshold.

·     Slow roaming—An AP performs roaming when the following conditions are met:

¡     The RSSI of the current wireless service is lower than the roaming RSSI threshold.

¡     The RSSI gap between an optimal wireless service and the current wireless service has exceeded the gap threshold.

Make sure the client mode is enabled before you execute this command. Disabling the client mode removes the configuration.

Examples

# Set the roaming RSSI threshold to 10 and the gap threshold to 2.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] client-mode roam rssi-threshold 10 gap 2

Related commands

client-mode enable

client-mode roam

client-mode roam scan-aging

Use client-mode roam scan-aging to set the scanning aging count for BSS entries.

Use undo client-mode roam scan-aging to restore the default.

Syntax

client-mode roam scan-aging count

undo client-mode roam scan-aging

Default

The scanning aging count for BSS entries is 5.

Views

Radio interface view

Predefined user roles

network-admin

Parameters

count: Specifies the aging count in the range of 1 to 10.

Usage guidelines

The AP generates an entry for each BSS detected through scanning. If the BSS cannot be detected again after the specified scanning intervals, the AP deletes the BSS entry. If the AP is associated with the deleted BSS, the AP goes offline from the BSS and then comes online from another BSS.

Make sure the client mode has been enabled on the interface before you perform this task. Disabling the client mode removes the aging count configuration.

Examples

# Set the scanning aging count for BSS entries to 5.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] client-mode roam scan-aging 5

Related commands

client-mode enable

client-mode roam scan-interval

Use client-mode roam scan-interval to set the roaming scanning interval.

Use undo client-mode roam scan-interval to restore the default.

Syntax

client-mode roam scan-interval interval

undo client-mode roam scan-interval

Default

The roaming scanning interval is 5000 milliseconds.

Views

Radio interface view

Predefined user roles

network-admin

Parameters

count: Specifies the scanning interval in the range of 100 to 10000 milliseconds.

Usage guidelines

Perform this task to set the interval at which the AP scans the network for beacon frames and probe responses. A short interval might result in frequent scanning, causing packet loss. A long interval might prevent the AP from discovering the optimal WLAN in time, affecting communication quality.

If roaming enhancement is disabled, you can set the interval only on the radio enabled with the client mode. Disabling the client mode removes the threshold configuration.

If roaming enhancement is enabled, you can set the interval only on the radio enabled with roaming enhancement. Disabling roaming enhancement removes the threshold configuration.

Examples

# Set the roaming scanning interval to 2000 milliseconds.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/2

[Sysname-WLAN-Radio1/0/2] client-mode roam scan-interval 2000

Related commands

client-mode enable

client-mode roam-enhance

Use client-mode roam-enhance to enable roaming enhancement on the fat AP.

Use undo client-mode roam-enhance to disable roaming enhancement on the fat AP.

Syntax

client-mode roam-enhance { quick | slow }

undo client-mode roam-enhance

Default

Roaming enhancement is disabled on the fat AP.

Views

Radio interface view

Predefined user roles

network-admin

Parameters

quick: Specifies quick roaming. In this mode, the AP performs roaming when the RSSI gap between an optimal wireless service and the current wireless service exceeds the gap threshold.

slow: Specifies slow roaming. In this mode, the AP performs roaming when the following conditions are met:

·     The RSSI of the current wireless service is lower than the roaming RSSI threshold.

·     The RSSI gap between an optimal wireless service and the current wireless service has exceeded the gap threshold.

Usage guidelines

In an Automated Guided Vehicle (AGV) system, client-mode fat APs deployed on the vehicles provide wireless access to onboard devices not equipped with a wireless NIC. In this networking mode, each fat AP must scan the network for better links and transmit data at the same time, which might cause packet loss.

To resolve this issue, enable roaming enhancement on the fat AP to enable the 2.4G radio to scan the network and the 5G radio to transmit data.

When you configure this feature, follow these restrictions and guidelines:

·     Enable roaming enhancement on the 2.4G radio and enable client mode on the 5G radio. Make sure auto roaming has been disabled before you enable roaming enhancement.

·     Enable automatic channel selection on the 5G radio.

·     To ensure good performance, do not configure the 2.4G radio to provide wireless access services.

·     Enabling this feature triggers the fat AP to go offline and then come online again.

·     To use the client-mode disconnect command to disconnect the fat AP from the WLAN, you must first disable roaming enhancement on the AP.

Examples

# Enable roaming enhancement and set the roaming mode to quick.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/2

[Sysname-WLAN-Radio1/0/2] client-mode roam-enhance quick

Related commands

client-mode roam rssi-threshold

client-mode ssid

Use client-mode ssid to specify an SSID for the client-mode AP and connect the AP to the SSID.

Use undo client-mode ssid to restore the default.

Syntax

client-mode ssid ssid

undo client-mode ssid

Default

No SSID is specified.

Views

Radio interface view

Predefined user roles

network-admin

Parameters

ssid: Specifies an SSID, a case-sensitive string of 1 to 32 characters.

Usage guidelines

Make sure the client mode is enabled before you execute this command. Disabling the client mode removes the configuration.

Examples

# Specify the SSID as service1 and connect the AP to the SSID.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] client-mode ssid service1

Related commands

client-mode enable

client-mode vlan

Use client-mode vlan to assign the radio interface with the client mode enabled to a VLAN.

Use undo client-mode ssid to restore the default.

Syntax

client-mode vlan vlan-id

undo client-mode vlan

Default

A radio interface with the client mode enabled is assigned to VLAN 1.

Views

Radio interface view

Predefined user roles

network-admin

Parameters

vlan-id: Specifies a VLAN ID in the range of 1 to 4094. If the specified VLAN does not exist, the AP creates the VLAN automatically.

Usage guidelines

Make sure the client mode is enabled before you execute this command. Disabling the client mode removes the configuration.

Examples

# Assign the radio interface to VLAN 2.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-WLAN-Radio1/0/1] client-mode vlan 2

Related commands

client-mode enable

customlog format wlan

Use customlog format wlan to enable the device to generate client logs in the specified format.

Use undo customlog format wlan to restore the default.

Syntax

customlog format wlan { normal | sangfor }

undo customlog format wlan

Default

The device generates client logs only in H3C format.

Views

System view

Predefined user roles

network-admin

Parameters

normal: Specifies normal format.

sangfor: Specifies sangfor format.

Usage guidelines

By default, the device generates client logs only in H3C format that logs AP name, radio ID, client MAC address, SSID, BSSID, and client online status.

You can configure the device to generate client logs in one of the following formats:

·     Normal—Logs AP MAC address, AP name, client IP address, client MAC address, SSID, and BSSID.

·     Sangfor—Logs AP MAC address, client IP address, and client MAC address.

This feature does not affect the generation of client logs in H3C format.

Examples

# Enable the device to generate client logs in sangfor format.

<Sysname> system-view

[Sysname] customlog format wlan sangfor

description

Use description to configure a description for a service template.

Use undo description to restore the default.

Syntax

description text

undo description

Default

No description is configured for a service template.

Views

Service template view

Predefined user roles

network-admin

Parameters

text: Specifies a description, a case-sensitive string of 1 to 64 characters.

Examples

# Configure a description for service template service1.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] description wlanst

display interface wlan-radio

Use display interface wlan-radio to display WLAN radio interface information.

Syntax

display interface wlan-radio [ interface-number ] [ brief ]

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

interface-number: Specifies a WLAN radio interface by its number. If you do not specify this argument, the command displays information about all WLAN radio interfaces.

brief: Displays brief interface information. If you do not specify this keyword, the command displays detailed interface information.

Examples

# Display detailed information about WLAN radio interface 1/0/1.

<Sysname> display interface wlan-radio 1/0/1

WLAN-Radio1/0/1                                                                 

Current state: UP                                                              

Description: WLAN-Radio1/0/1 Interface                                         

IP Packet Frame Type: PKTFMT_IEEE_802.11, Hardware Address: d461-fe59-4d20     

current mode: 802.11ac, current channel: 36                                    

Last link flapping: 0 hours 31 minutes 6 seconds                               

Last clearing of counters: Never                                                

Current system time:2016-01-01 00:31:19                                        

Last time when physical state changed to up:2016-01-01 00:00:13                

Last time when physical state changed to down:2016-01-01 00:00:13              

Input (total): 0 packets, 0 bytes                                    

Input (normal): 0packets, 0bytes                                     

                0 management, 0 control, 0 data                       

Input (error): 0 total, 0 CRC, 0 decrypt errors                          

               0 mic failures, 0 phy errors, 0 other errors                    

Output (total): 0 packets, 0 bytes                                   

Output (normal): Q[0]:0, Q[1]:0, Q[2]:0, Q[3]:0 packets                    

                 Q[0]:0, Q[1]:0, Q[2]:0, Q[3]:0 bytes                    

                 0 management, 0 control, 0 data                        

Output (bcn&probe): 0 packets, 0 bytes                               

Output (error): 0 total, 0 discard, 0 buffer failures                   

                0 ack failures, 0 rts successed, 0 rts failures 

Table 1 Command output

Field

Description

Current state

Physical link state of the interface:

·     UP—The interface is physically up.

·     DOWN—The interface is physically down.

·     ADM—The interface was shut down with the shutdown command. To bring up the interface, execute the undo shutdown command.

·     Stby—The interface is a backup interface.

IP Packet Frame Type

This field displays PKTFMT_IEEE_802.11, which indicates that the frame is 802.11 encapsulated.

Hardware Address

Interface MAC address.

current mode

Current radio mode.

current channel

Current working channel.

Last link flapping

The amount of time that has elapsed since the most recent physical state change of the interface. This field displays Never if the interface has been physically down since device startup.

Last clearing of counters

Time when the reset counters interface command was last used to clear the interface statistics. This field displays Never if the reset counters interface command has never been used on the interface since device startup.

Current system time

Current system time in the YYYY/MM/DD HH:MM:SS format. If a time zone is specified, this field displays the system time in the HH:MM:SS UTC±HH:MM:SS format.

Last time when physical state changed to up

Last time when the physical link state of the interface changed to up. This field displays - if the physical link state has never been changed.

Last time when physical state changed to down

Last time when the physical link state of the interface changed to down. This field displays - if the physical link state has never been changed.

Input(total): 0 packets, 0 bytes

Inbound packet statistics (in packets and bytes) for the interface. All inbound normal packets and abnormal packets were counted.

Input (normal): 0packets, 0bytes 0 management, 0 control, 0 data

Inbound normal packet statistics (in packets and bytes) for the interface. All normal inbound management, control, and data packets were counted.

Input (error)

Inbound error packet statistics for the interface.

Output (total): 0 packets, 0 bytes

Outbound packet statistics (in packets and bytes) for the interface. All outbound normal packets and abnormal packets were counted.

Output (normal): Q[0]:0, Q[1]:0, Q[2]:0, Q[3]:0 packets Q[0]:0, Q[1]:0, Q[2]:0, Q[3]:0 bytes 0 management, 0 control, 0 data

Outbound normal packet statistics (in packets and bytes) for the interface. All normal outbound management, control, and data packets were counted.

Q[n] represents an AC queue, where n represents the queue ID.

Output (bcn&probe)

Outbound beacon and probe frame statistics (in packets and bytes) for the interface.

Output (error)

Outbound error packet statistics for the interface.

# Display brief information about WLAN radio interface 1/0/1.

<Sysname> display interface wlan-radio 1/0/1 brief

Brief information on interfaces in bridge mode:                                

Link: ADM - administratively down; Stby - standby                              

Speed: (a) - auto                                                              

Duplex: (a)/A - auto; H - half; F - full                                       

Type: A - access; T - trunk; H - hybrid                                        

Interface            Link Speed     Duplex Type PVID Description               

WLAN-Radio1/0/1      UP   --        --     --   --     

Table 2 Command output

Field

Description

Brief information on interfaces in bridge mode

Brief information about Layer 2 interfaces.

Link

Physical link state of the interface:

·     ADM—The interface was shut down with the shutdown command. To restore the physical state of the interface, execute the undo shutdown command.

·     Stby—The interface is a backup interface. To display the primary interface, use the display interface-backup state command.

Speed

Speed of the interface, in Mbps.

This field displays the (a) flag next to the speed if the speed is automatically negotiated.

This field displays -- for WLAN radio interfaces.

Duplex

Duplex mode of the interface:

·     (a)/A—Autonegotiation.

·     H—Half duplex.

·     F—Full duplex.

This field displays -- for WLAN radio interfaces.

Type

Link type of the interface:

·     A—Access.

·     H—Hybrid.

·     T—Trunk.

This field displays -- for WLAN radio interfaces.

PVID

This field displays -- for WLAN radio interfaces.

Related commands

interface wlan-radio

display wlan ap all client-number

Use display wlan ap all client-number to display the number of online clients at the 2.4 GHz band and the 5 GHz band.

Syntax

display wlan ap all client-number

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display the number of online clients at both the 2.4 GHz and 5 GHz bands.

<System> display wlan ap all client-number

AP name           Clients           2.4GHz            5GHz

fatap             2                 2                 0

Table 3 Command output

Field

Description

Clients

Total number of online clients.

2.4GHz

Number of online clients at the 2.4 GHz band.

5GHz

Number of online clients at the 5 GHz band.

display wlan ap all radio client-number

Use display wlan ap all radio client-number to display the number of online clients and channel information for each radio.

Syntax

display wlan ap all radio client-number

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display the number of online clients and channel information for each radio.

<Sysname> display wlan ap all radio client-number

AP name                    RID     Channel     Clients

fatap                      1       44          12

fatap                      2       11          4

display wlan blacklist

Use display wlan blacklist to display blacklist entries.

Syntax

display wlan blacklist { dynamic | static }

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

dynamic: Specifies the dynamic blacklist.

static: Specifies the static blacklist.

Examples

# Display static blacklist entries.

<Sysname> display wlan blacklist static

Total number of clients: 3

 MAC addresses:

  000e-35b2-000e

  0019-5b8e-b709

  001c-f0bf-9c92

# Display dynamic blacklist entries.

<Sysname> display wlan blacklist dynamic

Total number of clients: 3

MAC address     APID  Lifetime (s)  Duration (hh:mm:ss)

000f-e2cc-0001  1     300           00:02:11

000f-e2cc-0002  2     300           00:01:17

000f-e2cc-0003  3     300           00:02:08

Table 4 Command output

Field

Description

MAC address

Client MAC address.

APID

ID of the AP that detects the rogue client.

Lifetime (s)

Lifetime of the entry in seconds.

Duration (hh:mm:ss)

Duration for the entry since the entry was added to the dynamic blacklist.

display wlan bss

Use display wlan bss to display basic service set (BSS) information.

Syntax

display wlan bss { all | bssid bssid } [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

all: Displays all BSSs.

bssid bssid: Specifies a BSS by its ID. The value is a 48-bit hexadecimal number in the format of H-H-H.

verbose: Displays detailed client information. If you do not specify this keyword, the command displays brief client information.

Examples

# Display brief information about all BSSs.

<Sysname> display wlan bss all

Total number of BSSs: 4

AP name                   RID  SSID                            BSSID

fatap                     1    SSID1                           001c-f08f-f804

fatap                     2    SSID1                           001c-f08f-f806

# Display detailed information about the BSS with ID 001c-f08f-f804.

<Sysname> display wlan bss bssid 001c-f08f-f804 verbose

AP name                       : fatap

BSSID                         : 001c-f08f-f804

Radio ID                      : 1

Service template name         : servcie1

SSID                          : SSID1

VLAN ID                       : 1

AKM mode                      : Not configured

User authentication mode      : Bypass

Table 5 Command output

Field

Description

AKM mode

AKM mode:

·     802.1X.

·     PSK.

·     Not configured.

User authentication mode

User authentication mode:

·     Bypass—No client authentication.

·     MAC.

·     802.1X.

·     OUI.

display wlan client

Use display wlan client to display client information.

Syntax

display wlan client [ interface wlan-radio interface-number | mac-address mac-address | service-template service-template-name | vlan vlan-id ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface wlan-radio interface-number: Displays information about clients that are connected to the specified radio interface.

mac-address mac-address: Specifies a client by its MAC address.

service-template service-template-name: Displays information about clients that are associated with the specified service template. The service template name is a case-insensitive string of 1 to 63 characters.

verbose: Displays detailed client information. If you do not specify this keyword, the command displays brief client information.

vlan vlan-id: Displays information about clients in the specified VLAN. The VLAN ID is in the range of 1 to 4094.

Examples

# Display brief information about all clients.

<Sysname> display wlan client

Total number of clients: 3

 

MAC address    Username         AP name       RID   IP address          VLAN

000f-e265-6400 N/A                  fatap                 1 1.1.1.1         100

000f-e265-6401 user                 fatap                 1 3.0.0.3         200

84db-ac14-dd08 N/A                  fatap                 1 5.5.5.3         1

Table 6 Command output

Field

Description

MAC address

Client MAC address.

Username

Client username:

·     The field displays the client username if the client uses 802.1X or MAC authentication.

·     The field displays N/A if the client does not use 802.1X or MAC authentication.

NOTE:

If the client uses portal authentication, this field does not display the portal username of the client.

AP name

Name of the AP that the client is associated with.

R

ID of the radio that the client is associated with.

IP address

IPv4 address of the client.

VLAN ID

ID of the VLAN to which the client belongs.

# Display detailed information about the client with MAC address 000f-e265-6400.

<Sysname> display wlan client mac-address 000f-e265-6400 verbose

Total number of clients: 1

 

MAC address                        : 000f-e265-6400

IPv4 address                       : 10.1.1.114

IPv6 address                       : 2001::1234:5678:0102:0304

Username                           : N/A

AID                                : 1

Radio ID                           : 1

SSID                               : office

BSSID                              : 0026-3e08-1150

VLAN ID                            : 3

Sleep count                        : 3

Wireless mode                      : 802.11gn

Channel bandwidth                  : 20MHz

20/40 BSS Coexistence Management   : Not supported

SM power save                      : Enabled

Short GI for 20MHz                 : Supported

Short GI for 40MHz                 : Supported

Short GI for 80MHz                 : Supported

Short GI for 160/80+80MHz          : Not supported

STBC RX capability                 : Not supported

STBC TX capability                 : Not supported

LDPC RX capability                 : Not supported

SU beamformee capability           : Not supported

MU beamformee capability           : Not supported

Beamformee STS capability          : N/A

Block Ack                          : TID 0 In

Supported VHT-MCS set              : NSS1 0, 1, 2, 3, 4, 5, 6, 7, 8, 9

                                     NSS2 0, 1, 2, 3, 4, 5, 6, 7, 8, 9

Supported HT MCS set               : 0, 1, 2, 3, 4, 5, 6, 7,

                                     8, 9, 10, 11, 12, 13, 14,

                                     15

Supported rates                    : 1, 2, 5.5, 6, 9, 11,

                                     12, 18, 24, 36, 48, 54 Mbps

QoS mode                           : WMM

Listen interval                    : 10

RSSI                               : 62

Rx/Tx rate                         : 130/195 Mpbs

Speed                              : N/A

Authentication method              : Open system

Security mode                      : PRE-RSNA

AKM mode                           : Not configured

Cipher suite                       : N/A

User authentication mode           : Bypass

WPA3 status                        : Disabled

Authorization ACL ID               : 3001(Not effective)

Authorization user profile         : N/A

Authorization CAR                  :

  Average input rate               : 102400 bps

  Average output rate              : 102400 bps

Roam status                        : N/A

Key derivation                     : SHA1

PMF status                         : Enabled

Forwarding policy name             : Not configured

Online time                        : 0days 0hours 1minutes 13seconds

FT status                          : Inactive

BTM status                         : Disabled

Table 7 Command output

Field

Description

MAC address

Client MAC address.

IPv4 address

Client IPv4 address.

IPv6 address

Client IPv6 address.

Username

Client username:

·     The field displays the client username if the client uses 802.1X or MAC authentication.

·     The field displays N/A if the client does not use 802.1X or MAC authentication.

NOTE:

If the client uses portal authentication, this field does not display the portal username of the client.

AID

Association ID.

Radio ID

ID of the radio that the client is associated with.

SSID

SSID with which the client is associated.

VLAN ID

ID of the VLAN to which the client belongs.

Sleep count

Client sleep times.

Wireless mode

Wireless mode:

·     802.11a.

·     802.11b.

·     802.11g.

·     802.11gn.

·     802.11an.

·     802.11ac.

·     802.11ax.

Channel bandwidth

Channel bandwidth:

·     20 MHz.

·     40 MHz.

·     80 MHz.

·     160 MHz.

20/40 BSS Coexistence Management

Whether the client supports 20/40MHz channel bandwidth coexistence.

SM Power Save

SM Power Save status:

·     Enabled—Only one antenna of a client operates in active state, and others operate in sleep state to save power.

·     Disabled.

Short GI for 20MHz

Whether the client supports short GI when its channel bandwidth is 20 MHz:

·     Supported.

·     Not supported.

Short GI for 40MHz

Whether the client supports short GI when its channel bandwidth is 40 MHz:

·     Supported.

·     Not supported.

Short GI for 80MHz

Whether the client supports short GI when its channel bandwidth is 80 MHz:

·     Supported.

·     Not supported.

Short GI for 160/80+80MHz

Whether the client supports short GI when its channel bandwidth is 160 MHz or 80 + 80 MHz:

·     Supported.

·     Not supported.

STBC Rx Capability

Client STBC receive capability;

·     Not Supported.

·     Supported.

STBC Tx Capability

Client STBC transmission capability:

·     Not Supported.

·     Supported.

LDPC Rx capability

Client LDPC receive capability;

·     Not Supported.

·     Supported.

SU beamformee capability

Client SU beamformee capability:

·     Not Supported.

·     Supported.

MU beamformee capability

Client MU beamformee capability:

·     Not Supported.

·     Supported.

Beamformee STS capability

Supported spatial stream quantity if the client is a beamformee receiver, in the range of 0 to 7 (the maximum spatial stream quantity specified by the MIMO mode minus one). This field displays N/A if the client cannot act as a beamformee receiver.

Number of Sounding Dimensions

Supported spatial stream quantity if the client is a beamformee transmitter, in the range of 0 to 7 (the maximum spatial stream quantity specified by the MIMO mode minus one). This field displays N/A if the client cannot act as a beamformee transmitter.

Block Ack

Negotiation result of Block ACK with TID:

·     TID 0 In—Sends Block ACK for inbound traffic.

·     TID 0 Out—Sends Block ACK for outbound traffic.

·     TID 0 Both—Sends Block ACK for both inbound and outbound traffic.

·     N/A—Does not send Block ACK for both inbound and outbound traffic.

Supported VHT-MCS set

VHT-MCS supported by the client.

Supported HT MCS set

HT-MCS supported by the client.

2.4G 40MHz Channel bandwidth

Client support for 2.4G 40 MHz channel bandwidth:

·     Not Supported.

·     Supported.

5G 40And80MHz  Channel bandwidth

Client support for 5G 40 MHz and 80 MHz channel bandwidth:

·     Not Supported.

·     Supported.

5G 160MHz  Channel bandwidth

Client support for 5G 160 MHz channel bandwidth:

·     Not Supported.

·     Supported.

5G 8080MHz  Channel bandwidth

Client support for 5G 80+80 MHz channel bandwidth:

·     Not Supported.

·     Supported.

OFDMA random access RUs

Support for OFDMA random selection of RUs.

·     Not Supported.

·     Supported.

Supported HE80MHz-MCS set

Supported 80 MHz HE-MCS sets.

Supported HE160MHz-MCS set

Supported 160 MHz HE-MCS sets.

Supported HE 8080MHz-MCS set

Supported 80+80 MHz HE-MCS sets.

QoS mode

QoS mode:

·     N/A—WMM is not supported.

·     WMM—WMM is supported.

WMM information negotiation is carried out between an AP and a client that both support WMM.

Listen interval

Interval at which the client wakes up to listen for beacon frames. It is counted by beacon interval.

RSSI

Received signal strength indication. This value indicates the client signal strength detected by the AP.

Rx/Tx rate

Sending and receiving rates of data, management, and control frames.

Speed

Sending and receiving rates in the past 2 minutes in Kbps, rounded to three decimal places.

This field displays N/A if both the sending and receiving rates are 0.

Authentication method

Authentication method:

·     Open system.

·     Shared key.

·     SAE.

Security mode

Security mode:

·     RSN—Beacons and probe responses carry RSN IE.

·     WPA—Beacons and probe responses carry WPA IE.

·     PRE-RSNA—Beacons and probe responses do not carry RSN IE or WPA IE.

AKM mode

AKM mode:

·     802.1X.

·     PSK.

·     OWE.

·     Not configured.

Cipher suite

Cipher suite:

·     N/A.

·     WEP40.

·     WEP104.

·     WEP128.

·     CCMP.

·     TKIP.

·     GCMP.

User authentication mode

User authentication mode:

·     Bypass—No client authentication.

·     MAC.

·     802.1X.

·     OUI.

WPA3 status

WPA3 status:

·     Disabled.

·     Enabled.

·     N/A.

Authorization ACL ID

Authorized ACL number:

·     This field displays the ACL number if the authorized ACL takes effect.

·     This field displays ACL number(Not effective) if the authorized ACL does not take effect.

·     This field displays N/A if the authentication server is configured without any authorized ACL.

Authorization user profile

Name of the authorized user profile:

·     This field displays the authorized user profile name if the authorized user profile takes effect.

·     This field displays authorized user profile name + Not effective if the authorized user profile does not take effect.

·     This field displays N/A if the authentication server is configured without any authorized user profile.

Authorization CAR

Authorization CAR:

·     Average input rate—Average uplink rate in bps.

·     Average output rate—Average downlink rate in bps.

·     N/A—This field displays N/A if the authentication server is not configured with authorization CAR for users.

Roam status

This field is not supported in the current software version.

Roam status:

·     Roaming in progress.

·     Inter-AC roam.

·     Inter-MA roam.

·     Intra-AC roam.

·     Intra-MA roam.

·     This field displays N/A if the client stays in one BSS after coming online.

Key derivation

Key derivation type:

·     SHA1—Uses the HMAC-SHA1 hash algorithm.

·     SHA256—Uses the HMAC-SHA256 hash algorithm.

·     SHA384—Uses the HMAC-SHA384 hash algorithm.

·     N/A—No key derivation algorithm is involved for the authentication type.

PMF status

PMF status:

·     Enabled—Management frame protection is enabled.

·     Disabled—Management frame protection is disabled.

·     N/A—Management frame protection is not involved.

Forwarding policy name

This field is not supported in the current software version.

WLAN forwarding policy name:

·     Not configured.

·     Policy-name.

Online time

Client online duration.

FT status

This field is not supported in the current software version.

Fast BSS transition (FT) status:

·     Active—FT is enabled.

·     Inactive—FT is disabled.

BTM status

BSS transition management (BTM) status:

·     Disabled.

·     Enabled.

display wlan client ipv6

Use display wlan client ipv6 to display information about client IPv6 addresses.

Syntax

display wlan client ipv6

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display brief status information about the specified client.

<Sysname> display wlan client ipv6

MAC address    AP name               IPv6 address                            VLAN

84db-ac14-dd08 fatap                 1::2:0:0:3                              300

Table 8 Command output

Field

Description

MAC address

Client MAC address.

IPv6 address

Client IPv6 address.

display wlan client online-duration

Use display wlan client online-duration to display client online duration.

Syntax

display wlan client online-duration [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

verbose: Displays detailed information. If you do not specify this keyword, the command displays brief information.

Examples

# Display brief information about client online duration.

<Sysname> display wlan client online-duration

Total number of online clients: 2

MAC address            IPv4 address    Online duration

a4c1-5b79-fa5b-1d62    192.168.11.123  0days 0hours 2minutes 23seconds

22d3-c5b7-a4b5-96fa    192.168.11.234  0days 0hours 5minutes 34seconds

Table 9 Command output

Field

Description

MAC address

Client MAC address.

IPv4 address

Client IPv4 address.

Online duration

Client online duration.

display wlan client status

Use display wlan client status to display client status information.

Syntax

display wlan client status [ mac-address mac-address ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

mac-address mac-address: Specifies a client by its MAC address in the format of H-H-H. If you do not specify this option, the command displays status information about all clients.

verbose: Displays detailed client status information. If you do not specify this keyword, the command displays brief client status information.

Examples

# Display brief status information about the specified client.

<Sysname> display wlan client status mac-address 001c-f08f-f804

Total number of clients: 1

 

MAC address     RSSI  Rx/Tx rate   Speed(bps)   Discard  AP name          RID

001c-f08f-f804  0     39M/117M      N/A          0.00     fatap            2

# Display brief status information about all clients.

<Sysname> display wlan client status

Total number of clients: 2

 

MAC address      RSSI  Rx/Tx rate   Speed(bps)   Discard  AP name          RID

000b-c002-9d09  65     39M/117M      N/A          0.00%    fatap            2

000f-e265-6401  62     130M/195M     N/A          0.00%    fatap            1

Table 10 Command output

Field

Description

MAC address

Client MAC address.

RSSI

RSSI of the client.

Rx/Tx rate

Rates at which the client receives and sends data, management packets, and control packets.

Speed(bps)

Rates at which the client receives and sends packets in the past 2 minutes, rounded to one decimal place.

If a rate is smaller than 1 Mbps, the value is displayed in Kbps. If a rate equals 1 Mbps or is larger than 1 Mbps, the value is displayed in Mbps. If a rate equals 1 Gbps or is larger than 1 Gbps, the value is displayed in Gbps.

This field displays N/A if both the sending and receiving rates are 0.

Discard

Ratio of packets discarded by the client.

AP name

Name of the AP with which the client is associated.

RID

ID of the radio with which the client is associated.

# Display detailed status information about the specified client.

<Sysname> display wlan client status mac-address 001c-f08f-f804 verbose

Total number of clients: 1

 

MAC address                       : 001c-f08f-f804

Radio ID                          : 2

RSSI                              : 0

Rx/Tx rate                        : 39/117 Mbps

Received:

 Retransmitted packets            : 84

 Retransmitted packet ratio       : 64.12 %

Sent:

 Retransmitted packets            : 0

 Retransmitted packet ratio       : 0.00 %

Discarded:

 Discarded packets                : 0

 Discarded packet ratio           : 0.00 %

Table 11 Command output

Field

Description

MAC address

Client MAC address.

Radio ID

ID of the radio that the client is associated with.

RSSI

RSSI of the client.

Rx/Tx rate

Rates at which the client receives and sends data, management packets, and control packets.

Received

Received packet statistics:

·     Retransmitted packets.

·     Retransmitted packet ratio.

Sent

Sent packet statistics:

·     Retransmitted packets.

·     Retransmitted packet ratio.

Discarded

Discarded packet statistics:

·     Discarded packets.

·     Discarded packet ratio.

display wlan client-mode packet-statistics

Use display wlan client-mode packet-statistics to display statistics about received and transmitted packets in client mode.

Syntax

display wlan client-mode packet-statistics radio radio-id

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

radio-id: Specifies a radio by its ID.

Examples

# Display statistics about received and transmitted packets in client mode.

<Sysname> display wlan client-mode packet-statistics radio 1

Packet statistics:

unknown                              : 0

recv beacon in scan                  : 65

recv beacon in run                   : 47164

recv probe response in fsm           : 49

recv probe response in run           : 0

recv probe response in scan          : 322

recv auth in fsm                     : 50

recv assoc response in fsm           : 50

recv deauth in fsm                   : 0

recv disassoc in fsm                 : 0

recv action in fsm                   : 5

recv other frame in fsm              : 5

recv other frame in scan             : 0

send auth success                    : 50

send auth failed                     : 0

send assoc success                   : 50

send assoc failed                    : 0

send deauth success                  : 49

send deauth failed                   : 0

send unicast probe success           : 50

send unicast probe failed            : 0

send broadcast probe(ssid) success   : 8

send broadcast probe(ssid) failed    : 0

send broadcast probe success         : 16

send broadcast probe failed          : 0

send null data success               : 0

send null data failed                : 0

Table 12 Command output

Field

Description

unknown

Number of received unknown frames.

recv beacon in scan

Number of received beacon frames at the scanning phase.

recv beacon in run

Number of received beacon frames after association.

recv probe response in fsm

Number of received probe responses at the association phase.

recv probe response in run

Number of received probe responses after association.

recv probe response in scan

Number of received probe responses at the scanning phase.

recv auth in fsm

Number of received authentication frames at the association phase.

recv assoc response in fsm

Number of received association responses at the association phase.

recv deauth in fsm

Number of received deauthentication frames at the association phase.

recv disassoc in fsm

Number of received disassociation frames at the association phase.

recv action in fsm

Number of received action frames at the association phase.

recv other frame in fsm

Number of received other frames at the association phase.

recv other frame in scan

Number of received other frames at the scanning phase.

send auth success

Number of authentication frames sent successfully.

send auth failed

Number of authentication frames failed to be sent.

send assoc success

Number of association frames sent successfully.

send assoc failed

Number of association frames failed to be sent.

send deauth success

Number of deauthentication frames sent successfully.

send deauth failed

Number of deauthentication frames failed to be sent.

send unicast probe success

Number of unicast probe requests sent successfully.

send unicast probe failed

Number of unicast probe requests failed to be sent.

send broadcast probe(ssid) success

Number of broadcast probe requests (carrying an SSID) sent successfully.

send broadcast probe(ssid) failed

Number of broadcast probe requests (carrying an SSID) failed to be sent.

send broadcast probe success

Number of broadcast probe requests sent successfully.

send broadcast probe failed

Number of broadcast probe requests failed to be sent.

send null data success

Number of null data packets sent successfully.

send null data failed

Number of null data packets failed to be sent.

Related commands

client-mode enable

reset wlan client-mode packet-statistics

display wlan client-mode radio

Use display wlan client-mode radio to display information about the radio interface with the client mode enabled.

Syntax

display wlan client-mode radio

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display information about the radio interface with the client mode enabled.

<Sysname> display wlan client-mode radio

Radio                          : 2

Mode                           : 802.11a

Authentication method          : Open-system

Cipher suite                   : N/A

Key (simple)                   : N/A

WEP Key ID                     : N/A

SSID                           : service1

BSSID                          : 6CF0-49CD-30BB

Status                         : Connected

Received data packets          : 1324939

Received management packets    : 34876

Sent data packets              : 46365

Discarded packets              : 38272

Supported rates                : 6, 9, 12, 18, 24, 36, 48, 54 Mbps

Online time                    : 0 days 0 hours 45 minutes 5 seconds

Table 13 Command output

Field

Description

Mode

Radio mode:

·     802.11a.

·     802.11b.

·     802.11g.

·     802.11an.

·     802.11gn.

·     802.11ac.

NOTE:

Support for the radio mode depends on the device model.

Authentication method

Authentication method:

·     Open-system.

·     Shared-key.

·     WPA2-PSK.

Cipher suite

Cipher suite:

·     CCMP.

·     TKIP.

·     WEP40.

·     WEP104.

·     WEP128.

·     N/A.

Key

Preshared key:

·     (Cipher)—Encrypted pre-shared key.

·     (Simple)—Plaintext pre-shared key.

·     N/A—No pre-shared key is configured.

WEP key ID

WEP key ID. This field displays N/A if no cipher suite is configured.

SSID

SSID with which the client-mode AP is associated.

Status

Connection status:

·     Connected—The AP is connected to the WLAN.

·     Disconnected—The AP is disconnected from the WLAN.

Received data packets

Number of received data packets.

Received management packets

Number of received management packets.

Sent data packets

Number of sent data packets.

Discarded packets

Number of discarded packets.

Online time

Online time of the AP.

display wlan client-mode roam-enhance bss

Use display wlan client-mode roam-enhance bss to display information about BSSs detected in client mode.

Syntax

display wlan client-mode roam-enhance bss

Views

Any view

Predefined user roles

network-admin

network-operator

Usage guidelines

This command displays information about BSSs carried in beacon frames and probe responses detected in the most recent five scanning operations.

Examples

# Display information about BSSs detected in client mode.

<Sysname> display wlan client-mode roam-enhance bss

Total number of BSSs: 2

BSSID          Time      MSec  RSSI AVER CHL  AGE SSID

84d9-3100-4b00 16:51:09  0244  37   36   149  5   agv-work

               16:51:08  0834  37                  

               16:51:08  0732  36

               16:51:08  0642  37

               16:51:09  0253  36

50da-00df-33e0 16:51:08  0802  45   45   149  5   agv-work

               16:51:08  0699  44

               16:51:08  0597  46

               16:51:08  0261  46

               16:51:09  0251  45

Table 14 Command output

Field

Description

Time

Time at which the beacon frame or probe response was received.

MSec

Time at which the beacon frame or probe response was received, in milliseconds.

AVER

Average RSSI of the five most recently received frames that carry the BSSID.

CHL

Channel carried in the frame received most recently.

AGE

Aging count for the BSS entry.

display wlan client-mode roaming-state

Use display wlan client-mode roaming-state to display roaming state changes of the AP in client mode.

Syntax

display wlan client-mode roaming-state

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display roaming state changes of the AP in client mode.

<Sysname> display wlan client-mode roaming-state

Radio ID: 1           FSM changes: 9               SSID: agv

Index FSM  BSSID          RSSI Chl FsmChangeCause         Time

1     UnAu 50da-00df-33e0 55   36  Send prob(Bss)         Day 2 18:12:36 987

2     Auth 50da-00df-33e0 55   36  Auth direct(Bss)       Day 2 18:12:36 35

3     Asso 50da-00df-33e0 55   36  Send assoc             Day 2 18:12:36 37

4     Run  50da-00df-33e0 55   36  Rec assoc              Day 2 18:12:36 38

5     UnAu 50da-00df-33e0 55   36  Scan aging             Day 2 18:12:41 39

6     UnAu 50da-00df-33e0 47   149 Send prob(chlchg)      Day 4 8:49:5 41

7     Auth 50da-00df-33e0 47   149 Auth direct(Bss)       Day 4 8:49:5 42

8     Asso 50da-00df-33e0 47   149 Send assoc             Day 4 8:49:5 43 9

9     Run  50da-00df-33e0 47   149 Rec assoc              Day 4 8:49:5 46

Table 15 Command output

Field

Description

Radio ID

ID of the radio in client mode.

FSM changes

Number of state changes during the association process.

FSM

Device state. Options include:

·     Init—The device is in initialization state.

·     UnAu—The device has not been authenticated.

·     Auth—The device is being authenticated.

·     Asso—The device is attempting to associate with a WLAN.

·     Run—The device is in running state.

·     N/A—The device is in abnormal state.

Chl

Channel ID.

FsmChangeCause

State change reason. Options include:

·     Rec prob resp—The device received a probe response and sent an authentication frame.

·     Send assoc req—The device sent an association request.

·     Rec assoc resp—The device received an association response.

·     Rec deauth—The device received a deauthentication frame.

·     Rec disasso—The device received a disassociation frame.

·     Unauth timeout—The unauthentication state timed out and the AP sent an authentication frame.

·     Unauth timeout fail—The unauthentication state timed out and the AP sent an authentication failure frame.

·     Auth timeout—The authentication state timed out.

·     Asso timeout—The association state timed out.

·     Keepalive beacon timeout—The beacon-based keepalive timed out.

·     Rec action—The device received an action frame.

·     Init to unauth—The device state changed from initialization to unauthentication.

·     Disconnect(cfg)—Connection terminated because of manual configuration.

·     Undo SSID—The SSID configuration was removed.

·     Send prob req(chlchg)—The AP sent a probe request after a channel change.

·     Send prob req fail(chlchg)—The AP failed to send a probe request after a channel change.

·     Radio down—The associated radio became unavailable.

·     Prob resp fail—The AP failed to process a probe response.

·     Auth fail(open system)—The AP failed to process an open system authentication frame.

·     Auth fail(share key)—The AP failed to process a shared key authentication frame.

·     Asso resp fail—The AP failed to process an association response.

·     Chl Chg IE(beacon)—The channel changed in a received beacon frame.

·     Chl Chg IE(probe)—The channel changed in a received probe response.

·     Send prob req(unchlchg)—The AP sent a probe request and did not change its channel.

·     Connect BSS fail—The AP failed to access a BSS.

·     Share-key fail—Shared key authentication failed during association.

·     4H fail—Four-way handshake failed during association.

·     Select BSS by roam—The AP performed a BSS roaming.

·     Disconnect(dbm)—Disabling the client mode triggered AP reassociation.

·     Scan aging—The entry for the associated BSS expired.

·     Unauth timeout—The AP failed to receive probe responses in UnAuth state and stays in UnAuth state.

·     Auth direct—The AP did not receive any probe response and sent an authentication frame directly.

·     Active detect timeout—The probe request-based keepalive timed out.

·     Disconnect(RSSI)—The RSSI of the current link dropped below the link hold RSSI.

·     Roam enhance enabled—Roaming enhancement was enabled.

·     Unknown.

Time

Time at which the state change occurred.

Related commands

client-mode enable

reset wlan client-mode roaming-state

display wlan client-mode ssid

Use display wlan client-mode ssid to display information about detected SSIDs.

Syntax

display wlan client-mode ssid [ ssid ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameter

ssid: Specifies an SSID by its name, a case-sensitive string of 1 to 32 characters. If you do not specify this argument, the command displays information about all SSIDs with an RSSI equal to or higher than 15.

Usage guidelines

If roaming enhancement is disabled, the command displays information about all detected SSIDs.

If roaming enhancement is enabled and the client-mode ssid command has been executed, the display command displays information about the specified SSID.

If roaming enhancement is enabled but the client-mode ssid command has not been executed, the display command displays information about all detected SSIDs enabled with roaming enhancement.

Examples

# Display information about detected SSIDs.

<Sysname> display wlan client-mode ssid

SSID                              BSSID              Type    RSSI     Quality

service1                          1A76-2435-FD21     Clear   55       *****

Temp                              2334-5431-BDA1     WPA2    19       **

TC                                6CF0-AAFD-12FF     WEP     22       **

Test                              4512-ABC4-F555     Unknown 17       **

Lab                               4138-FAB7-8545     Clear   39       ****

Home_123456789000000000000000000  F643-ABD4-439F     WPA2    27       ***

Table 16 Command output

Field

Description

Type

Encryption type:

·     Clear.

·     WPA2.

·     WEP.

·     Unknown.

Quality

Signal quality:

·     *****—RSSI 45.

·     ****—35 RSSI < 45.

·     ***—25 RSSI < 35.

·     **—15 RSSI < 25.

·     *—0 < RSSI < 15.

·     No Signal—RSSI = 0.

display wlan service-template

Use display wlan service-template to display service template information.

Syntax

display wlan service-template [ service-template-name ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

service-template-name: Specifies a service template by its name, a case-insensitive string of 1 to 63 characters. If you do not specify this argument, the command displays information about all service templates.

verbose: Displays detailed service template information.

Examples

# Display brief information about all service templates.

[Sysname] display wlan service-template

Total number of service templates: 2

Service template name           SSID                                    Status

1                               2333                                    Enabled

2                               3222                                    Enabled

# Display detailed information about all service templates.

<Sysname> display wlan service-template verbose

Service template name                            : service1

Description                                      : Not configured

SSID                                             : wuxianfuwu

SSID-hide                                        : Disabled

User-isolation                                   : Disabled

Service template status                          : Disabled

Maximum clients per BSS                          : 64

VLAN ID                                          : 1

Customer Vlan                                    : 3

AKM mode                                         : PSK

Security IE                                      : RSN

Cipher suite                                     : CCMP

WEP key ID                                       : 1

TKIP countermeasure time                         : 100 sec

PTK lifetime                                     : 43200 sec

PTK rekey                                        : Enabled

GTK rekey                                        : Enabled

GTK rekey method                                 : Time-based

GTK rekey time                                   : 86400 sec

GTK rekey client-offline                         : Enabled

WPA3 status                                      : Disabled

Enhance-open status                              : Enabled

Enhanced-open transition-mode service-template   : N/A

User authentication mode                         : Bypass

Intrusion protection                             : Disabled

Intrusion protection mode                        : Temporary-block

Temporary block time                             : 180 sec

Temporary service stop time                      : 20 sec

Fail VLAN ID                                     : 1

802.1X handshake                                 : Enabled

802.1X handshake secure                          : Disabled

802.1X domain                                    : my-domain

MAC-auth domain                                  : Not configured

Max 802.1X users per BSS                         : 4096

Max MAC-auth users per BSS                       : 4096

802.1X re-authenticate                           : Enabled

Authorization fail mode                          : Online

Accounting fail mode                             : Online

Authorization                                    : Permitted

Key derivation                                   : SHA1

PMF status                                       : Optional

Hotspot policy number                            : Not configured

Forwarding policy status                         : Disabled

Forwarding policy name                           : Not configured

Forwarder                                        : AP

FT status                                        : Disabled

QoS trust                                        : Port

QoS priority                                     : 0

BTM status                                       : Disabled

Table 17 Command output

Field

Description

SSID

SSID of the service template.

SSID-hide

Whether the SSID is hidden in beacons:

·     Disabled.

·     Enabled.

User-isolation

Use isolation:

·     Disabled.

·     Enabled.

Service template status

Service template status:

·     Disabled.

·     Enabled.

Maximum clients per BSS

Maximum number of clients that the BSS supports.

VLAN ID

ID of the VLAN to which clients belong after they come online through the service template.

Customer Vlan

ID of the inner VLAN to which clients belong after they come online through the service template.

AKM mode

AKM mode:

·     802.1X.

·     PSK.

Security IE

Security IE:

·     RSN.

·     WPA.

Cipher suite

Cipher suite:

·     WEP40.

·     WEP104.

·     WEP128.

·     TKIP.

·     CCMP.

·     GCMP.

TKIP countermeasure time

TKIP countermeasure time. The value 0 indicates no countermeasures are taken.

PTK rekey

Whether PTK rekey is enabled:

·     Enabled.

·     Disabled.

GTK rekey

Whether GTK rekey is enabled:

·     Enabled.

·     Disabled.

GTK rekey method

GTK rekey method:

·     Time-based.

·     Packet-based.

GTK rekey time

GTK rekey interval.

GTK rekey packets

Number of packets that can be transmitted before the GTK is refreshed.

GTK rekey client-offline

Whether client-off GTK rekey is enabled:

·     Enabled.

·     Disabled.

WPA3 status

WPA3 security mode:

·     Disabled.

·     Mandatory.

·     Optional.

Enhance-open status

Whether enhanced open system authentication is enabled:

·     Disabled.

·     Enabled.

Enhanced-open transition-mode service-template

Recommended service template in transition mode. If no service template is specified, this field displays N/A.

User authentication mode

Authentication mode:

·     Bypass—No authentication.

·     MAC.

·     MAC-or-802.1X—MAC authentication is performed first. If MAC authentication fails, 802.1X authentication is performed.

·     802.1X.

·     802.1X-or-MAC—802.1X authentication is performed first. If 802.1X authentication fails, MAC authentication is performed.

·     OUI-or-802.1X—OUI authentication is performed first. If OUI authentication fails, 802.1X authentication is performed.

·     MAC-and-802.1X—MAC authentication is performed first. If MAC authentication succeeds, 802.1X authentication is performed.

Intrusion protection

Whether intrusion protection is enabled:

·     Enabled.

·     Disabled.

Intrusion protection mode

Intrusion protection mode:

·     Temporary-block—Temporarily adds intruders to the block list.

·     Service-stop—Stops all services provided by the BSS that receives illegal packets until it resets.

·     Temporary-service-stop—Temporarily stops the access service provided by the BSS that receives illegal packets.

Temporary block time

Temporary block time in seconds.

Temporary service stop time

Temporary service stop time in seconds.

Fail VLAN ID

ID of the VLAN to which clients are added if they cannot pass the authentication when the authentication server can be reached. This field displays Not configured if the fail VLAN ID is not configured.

Critical VLAN ID

ID of the VLAN to which clients are added if they cannot pass the authentication because the authentication server cannot be reached. This field displays Not configured if the critical VLAN ID is not configured.

802.1X handshake

Whether 802.1X handshake is enabled:

·     Enabled.

·     Disabled.

802.1X handshake secure

Whether secure 802.1X handshake is enabled:

·     Enabled.

·     Disabled.

802.1X domain

802.1X authentication domain. This field displays Not configured if the domain is not configured.

MAC-auth domain

MAC authentication domain. This field displays Not configured if the domain is not configured.

Max 802.1X users per BSS

Maximum number of supported 802.1X users in a BSS.

Max MAC-auth users per BSS

Maximum number of supported users that pass the MAC authentication in a BSS.

802.1X re-authenticate

Whether 802.1X reauthentication is enabled:

·     Enabled.

·     Disabled.

Authorization fail mode

Authorization fail mode:

·     Offline—Clients are logged off when authorization fails.

·     Online—Clients are not logged off when authorization fails.

Accounting fail mode

Accounting fail mode:

·     Offline—Clients are logged off when accounting fails.

·     Online—Clients are not logged off when accounting fails.

Authorization

Authorization information:

·     Permitted—Applies the authorization information issued by the RADIUS server or the local device.

·     Ignored—Ignores the authorization information issued by the RADIUS server or the local device.

Key derivation

Key derivation type:

·     SHA1—Uses the HMAC-SHA1 hash algorithm.

·     SHA256—Uses the HMAC-SHA256 hash algorithm.

·     SHA1-AND-SHA256—Uses the HMAC SHA1 and SHA256 hash algorithm.

PMF status

PMF status:

·     Disabled—Management frame protection is disabled.

·     Optional—Management frame protection in optional mode is enabled.

·     Mandatory—Management frame protection in mandatory mode is enabled.

Hotspot policy number

This field is not supported in the current software version.

Hotspot 2.0 policy number.

Forwarding policy status

This field is not supported in the current software version.

WLAN forwarding policy status:

·     Disabled.

·     Enabled.

Forward policy name

This field is not supported in the current software version.

WLAN forwarding policy name:

·     Not configured—No WLAN forwarding policy is configured.

·     policy-name.

Forwarder

Client traffic forwarder:

AP.

FT status

This field is not supported in the current software version.

FT status:

·     Disabled.

·     Enabled.

FT method

This field is not supported in the current software version.

FT method:

·     over-the-air.

·     over-the-ds.

FT reassociation deadline

This field is not supported in the current software version.

FT reassociation timeout timer in seconds.

QoS trust

QoS priority trust mode:

·     Port—Port priority trust mode.

·     Dot11e—802.11e priority trust mode.

QoS priority

Port priority in the range of 0 to 7.

BTM status

BSS Transition Management (BTM) status:

·     Disabled.

·     Enabled.

display wlan statistics client

Use display wlan statistics client to display client statistics.

Syntax

display wlan statistics client [ mac-address mac-address ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

mac-address mac-address: Specifies a client by its MAC address. If you do not specify this option, the command displays statistics for all clients.

Examples

# Display statistics for all clients.

<Sysname> display wlan statistics client

MAC address                : 0014-6c8a-43ff

AP name                    : fatap

Radio ID                   : 1

SSID                       : office

BSSID                      : 000f-e2ff-7700

RSSI                       : 31

Sent frames:

  Back ground              : 0/0 (frames/bytes)

  Best effort              : 9/1230 (frames/bytes)

  Video                    : 0/0 (frames/bytes)

  Voice                    : 2/76 (frames/bytes)

Received frames:

  Back ground              : 0/0 (frames/bytes)

  Best effort              : 18/2437 (frames/bytes)

  Video                    : 0/0 (frames/bytes)

  Voice                    : 7/468 (frames/bytes)

Discarded frames:

  Back ground              : 0/0 (frames/bytes)

  Best effort              : 0/0 (frames/bytes)

  Video                    : 0/0 (frames/bytes)

  Voice                    : 5/389 (frames/bytes)

Table 18 Command output

Field

Description

SSID

SSID of the service template.

MAC address

Client MAC address.

Back ground

AC-BK queue.

Best effort

AC-BE queue.

Video

AC-VI queue.

Voice

AC-VO queue.

display wlan statistics connect-history

Use display wlan statistics connect-history to display client connection history.

Syntax

display wlan statistics connect-history service-template service-template-name

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

service-template service-template-name: Specifies a service template by its name.

Examples

# Display the connection history for service template 1.

<Sysname> display wlan statistics connect-history service-template 1

AP name                     : fatap

Radio ID                    : 1

Associations                : 132

Association failures        : 3

Reassociations              : 30

Rejections                  : 12

Abnormal disassociations    : 2

Current associations        : 57

display wlan statistics service template

Use display wlan statistics service-template to display service template statistics.

Syntax

display wlan statistics service-template service-template-name

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

service-template service-template-name: Specifies a service template by its name.

Examples

# Display statistics for service template 1.

<Sysname> display wlan statistics service-template 1

AP name                       : fatap

Radio ID                      : 1

Received:

  Frame count                 : 1713

  Frame bytes                 : 487061

  Data frame count            : 1683

  Data frame bytes            : 485761

  Association request count   : 2

Sent:

  Frame count                 : 62113

  Frame bytes                 : 25142076

  Data frame count            : 55978

  Data frame bytes            : 22626600

  Association response count  : 2

display wlan whitelist

Use display wlan whitelist to display whitelist entries.

Syntax

display wlan whitelist

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display whitelist entries.

<Sysname> display wlan whitelist

Total number of clients: 3

 MAC addresses:

  000e-35b2-000e

  0019-5b8e-b709

  001c-f0bf-9c92

interface wlan-radio

Use interface wlan-radio to enter WLAN radio interface view.

Syntax

interface wlan-radio interface-number

Views

System view

Predefined user roles

network-admin

Examples

interface-number: Specifies the WLAN radio interface ID.

Examples

# Enter interface view of WLAN radio interface 1/0/1.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-wlan-radio-1]

Related commands

display interface wlan-radio

nas-id

Use nas-id to set the network access server identifier (NAS ID).

Syntax

nas-id nas-id

undo nas-id

Default

No NAS ID is specified.

Views

Global configuration view

Predefined user roles

network-admin

Parameters

nas-id: Specifies a NAS ID, a case-sensitive string of 1 to 63 characters.

Usage guidelines

After coming online, a client sends a RADIUS request that carries the NAS ID to the RADIUS server to indicate its network access server.

Examples

# Set the global NAS ID to abc123.

<Sysname> system-view

[Sysname] wlan global-configuration

[Sysname-wlan-global-configuration] nas-id abc123

nas-port-type

Use nas-port-type to set the NAS port type attribute in RADIUS requests.

Use the undo nas-port-type to restore the default.

Syntax

nas-port-type value

undo nas-port-type

Default

The NAS port type is Wireless-IEEE 802.11.

Views

Service template view

Predefined user roles

network-admin

Parameters

value: Specifies a NAS port type by its code value in the range of 0 to 255. Table 19 lists the most commonly used NAS port types and their code values.

Table 19 Common NAS port types and their code values

NAS port type

Code value

Async

0

Sync

1

ISDN Sync

2

ISDN Async V.120

3

ISDN Async V.110

4

Virtual

5

PIAFS

6

HDLC Clear Channel

7

X.25

8

X.75

9

G.3 Fax

10

SDSL

11

ADSL-CAP

12

ADSL-DMT

13

IDSL

14

Ethernet

15

xDSL

16

Cable

17

Wireless-Other

18

Wireless-IEEE 802.11

19

Usage guidelines

You can execute this command to set the NAS port type attribute in RADIUS requests for 802.11X and MAC-authenticated clients.

Make sure the service template is disabled before you execute this command.

Examples

# Set the NAS port type in RADIUS requests to 15 (Ethernet).

<Sysname> system-view

[Sysname] wlan service-template 1

[Sysname-wlan-st-1] nas-port-type 15

quick-association enable

Use quick-association to enable quick association.

Use undo quick-association to disable quick association.

Syntax

quick-association enable

undo quick-association enable

Default

Quick association is disabled.

Views

Service template view

Predefined user roles

network-admin

Usage guidelines

This command disables APs from performing load balancing or band navigation on clients associated with the specified service template.

Examples

# Enable quick association for service template service1.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1]quick-association enable

reset wlan client

Use reset wlan client to log off a client or all clients.

Syntax

reset wlan client { all | mac-address mac-address }

View

User view

Predefined user roles

network-admin

Parameters

all: Specifies all clients.

mac-address mac-address: Specifies a client by its MAC address.

Examples

# Log off all clients.

<Sysname> reset wlan client all

Related commands

display wlan client

reset wlan client-mode packet-statistics

Use reset wlan client-mode packet-statistics to clear statistics about received and transmitted packets in client mode.

Syntax

reset wlan client-mode packet-statistics radio radio-id

View

User view

Predefined user roles

network-admin

Parameters

radio-id: Specifies a radio by its ID.

Examples

# Clear statistics about received and transmitted packets in client mode.

<Sysname> reset wlan client-mode packet-statistics radio 1

Related commands

client-mode enable

display wlan client-mode packet-statistics

reset wlan client-mode roaming-state

Use reset wlan client-mode roaming-state to clear information about BSSs detected in client mode.

Syntax

reset wlan client-mode roaming-state

View

User view

Predefined user roles

network-admin

Examples

# Clear information about BSSs detected in client mode.

<Sysname> reset wlan client-mode roaming-state

Related commands

client-mode enable

display wlan client-mode roaming-state

reset wlan dynamic-blacklist

Use reset wlan dynamic-blacklist to remove the specified client or all clients from the dynamic blacklist.

Syntax

reset wlan dynamic-blacklist [ mac-address mac-address ]

Views

User view

Predefined user roles

network-admin

Parameters

mac-address mac-address: Specifies a client by its MAC address. If you do not specify this option, the command removes all clients from the dynamic blacklist.

Examples

# Remove all clients from the dynamic blacklist.

<Sysname> reset wlan dynamic-blacklist

# Remove the specified client from the dynamic blacklist.

<Sysname> reset wlan dynamic-blacklist mac-address b8ca-32a2-df69

Related commands

display wlan blacklist

reset wlan statistics client

Use reset wlan statistics client to clear client statistics.

Syntax

reset wlan statistics client { all | mac-address mac-address }

View

User view

Predefined user roles

network-admin

Parameters

all: Specifies all clients.

mac-address mac-address: Specifies a client by its MAC address.

Examples

# Clear statistics about all clients.

<Sysname> reset wlan statistics client all

Related commands

display wlan statistics

reset wlan statistics service-template

Use reset wlan statistics service-template to clear service template statistics.

Syntax

reset wlan statistics service-template service-template-name

View

User view

Predefined user roles

network-admin

Parameters

service-template-name: Specifies a service template by its name, a case-insensitive string of 1 to 63 characters.

Examples

# Clear statistics about service template service1.

<Sysname> reset wlan statistics service-template service1

Related commands

display wlan statistics

service-template

Use service-template to bind a service template to a radio interface.

Use undo service-template to unbind a service template from a radio interface.

Syntax

service-template service-template-name

undo service-template service-template-name

Default

In radio interface view, no service template is bound to a radio interface.

Views

Radio interface view

Predefined user roles

network-admin

Parameters

service-template-name: Specifies a service template by its name, a case-insensitive string of 1 to 63 characters.

Usage guidelines

Before you bind a service template to a radio or a radio interface, you must create the service template.

Examples

# Bind service template service1 to interface WLAN-Radio 1/0/1.

<Sysname> system-view

[Sysname] interface wlan-radio 1/0/1

[Sysname-wlan-radio-1] service-template service1

service-template enable

Use service-template enable to enable a service template.

Use undo service-template enable to disable a service template.

Syntax

service-template enable

undo service-template enable

Default

A service template is disabled.

Views

Service template view

Predefined user roles

network-admin

Usage guidelines

If the number of BSSs on a device exceeds the limit, you cannot enable a new service template.

Examples

# Enable service template service1.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] service-template enable

snmp-agent trap enable wlan client

Use snmp-agent trap enable wlan client to enable SNMP notification for client access.

Use undo snmp-agent trap enable wlan client to disable SNMP notification for client access.

Syntax

snmp-agent trap enable wlan client

undo snmp-agent trap enable wlan client

Default

SNMP notification is disabled for client access.

Views

System view

Predefined user roles

network-admin

Usage guidelines

When this feature is enabled, the device sends a client status change notification to an NMS every time the status of a client changes. For the notifications to be sent correctly, you must also configure SNMP as described in Network Management and Monitoring Configuration Guide.

Examples

# Enable SNMP notification for client access.

<Sysname> system-view

[Sysname] snmp-agent trap enable wlan client

snmp-agent trap enable wlan client-audit

Use snmp-agent trap enable wlan client-audit to enable SNMP notification for client audit.

Use undo snmp-agent trap enable wlan client-audit to disable SNMP notification for client audit.

Syntax

snmp-agent trap enable wlan client-audit

undo snmp-agent trap enable wlan client-audit

Default

SNMP notification is disabled for client audit.

Views

System view

Predefined user roles

network-admin

Usage guidelines

When this feature is enabled, the device sends a client status change notification to an NMS when a client comes online, goes offline, roams to another AP, or obtains an IP address. For the notifications to be sent correctly, you must also configure SNMP as described in Network Management and Monitoring Configuration Guide.

Examples

# Enable SNMP notification for client audit.

<Sysname> system-view

[Sysname] snmp-agent trap enable wlan client-audit

ssid

Use ssid to set an SSID for a service template.

Use undo ssid to restore the default.

Syntax

ssid ssid-name

undo ssid

Default

No SSID is configured for a service template.

Views

Service template view

Predefined user roles

network-admin

Parameters

ssid-name: Specifies an SSID name, a case-sensitive string of 1 to 32 characters.

Usage guidelines

Disable the service template before you execute this command.

Examples

# Set the SSID to lynn for service template service1.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] ssid lynn

unknown-client

Use unknown-client to set the way that an AP processes traffic from unknown clients.

Use undo unknown-client to restore the default.

Syntax

unknown-client { deauthenticate | drop }

undo unknown-client

Default

An AP drops packets from unknown clients and deauthenticates these clients.

Views

Service template view

Predefined user roles

network-admin

Parameters

deauthenticate: Drops packets from unknown clients and deauthenticates these clients.

drop: Drops packets from unknown clients.

Examples

# Configure APs that use service template example to drop packets from unknown clients but not deauthenticate these clients.

<Sysname> system-view

[Sysname] wlan service-template example

[Sysname-wlan-st-example] unknown-client drop

vlan

Use vlan to assign clients coming online through a service template to the specified VLAN.

Use undo vlan to restore the default.

Syntax

vlan vlan-id

undo vlan

Default

Clients are assigned to VLAN 1 after coming online through a service template.

Views

Service template view

Predefined user roles

network-admin

Parameters

vlan-id: Specifies a VLAN by its VLAN ID, in the range of 1 to 4094.

Usage guidelines

Disable the service template before you execute this command.

If the specified VLAN does not exist, this command creates the VLAN when clients come online.

Examples

# Assign clients coming online through service template service1 to VLAN 2.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] vlan 2

wlan association optimization

Use wlan association optimization to set the index for optimizing client association ratios.

Use undo wlan association optimization to restore the default.

Syntax

wlan association optimization value

undo wlan association optimization

Default

The index is 0. The device does not optimize client association ratios.

Views

System view

Predefined user roles

network-admin

Parameters

value: Specifies the index for optimizing client association ratios, in the range of 900 to 1000. The smaller the index is, the smaller the calculated association success ratio will be and the larger the calculated congestion ratio and abnormal disassociation ratio will be.

Usage guidelines

This feature enables the device to recalculate the client association success ratio, association congestion ratio, and abnormal disassociation ratio by using the specified index to get smaller ratio values.

The client association success ratio is the number of successful client associations divided by the total number of client association attempts. The client association congestion ratio is the number of failed client associations caused by AP overloading divided by the total number of client association attempts. The client abnormal disassociation ratio is the number of abnormal disassociations divided by the sum of successful associations and online clients.

Examples

# Set the index for optimizing client association ratios to 950.

<Sysname> system-view

[Sysname] wlan association optimization 950

wlan broadcast-probe reply

Use wlan broadcast-probe reply to enable the AP to respond to broadcast probe requests.

Use undo wlan broadcast-probe reply to disable the AP from responding to broadcast probe requests.

Syntax

wlan broadcast-probe reply

undo wlan broadcast-probe reply

Default

The AP responds to all broadcast probe requests.

Views

System view

Predefined user roles

network-admin

Examples

# Disable the AP from responding to broadcast probe requests.

<Sysname> system-view

[Sysname] undo wlan broadcast-probe reply

wlan client idle-timeout

Use wlan client idle-timeout to set the client idle timeout timer.

Use undo wlan client idle-timeout to restore the default.

Syntax

wlan client idle-timeout timeout

undo wlan client idle-timeout

Default

The client idle timeout timer is 3600 seconds.

Views

System view

Predefined user roles

network-admin

Parameters

timeout: Specifies the client idle timeout timer in the range of 60 to 86400 seconds.

Usage guidelines

If an online client does not send any frames to the associated AP before the client idle timeout timer expires, the AP logs off the client.

Examples

# Set the client idle timeout timer to 2000 seconds.

<Sysname> system-view

[Sysname] wlan client idle-timeout 2000

wlan client keep-alive

Use wlan client keep-alive enable to enable client keepalive.

Use undo wlan client keep-alive to disable client keepalive.

Syntax

wlan client keep-alive enable

undo wlan client keep-alive

Default

Client keepalive is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

This feature enables the AP to send keepalive packets to clients at the specified intervals to determine whether the clients are online. If the AP does not receive any replies from a client within three keepalive intervals, it logs off the client.

Examples

# Enable client keepalive.

<Sysname> system-view

[Sysname] wlan client keep-alive enable

Related commands

wlan client keep-alive interval

wlan client keep-alive interval

Use wlan client keep-alive interval to set the client keepalive interval.

Use undo wlan client keep-alive interval to restore the default.

Syntax

wlan client keep-alive interval interval

undo wlan client keep-alive interval

Default

The client keepalive interval is 300 seconds.

Views

System view

Predefined user roles

network-admin

Parameters

interval: Specifies the client keepalive interval in the range of 3 to 1800 seconds.

Usage guidelines

Enable client keepalive on the AP before you execute this command.

This feature enables an AP to send keepalive packets to clients at the client keepalive interval to determine whether the clients are online. If the AP does not receive any replies from a client within three keepalive intervals, it logs off the client.

Examples

# Set the client keepalive interval to 1000 seconds.

<Sysname> system-view

[Sysname] wlan client keep-alive interval 1000

Related commands

wlan client keep-alive

wlan client reauthentication-period

Use wlan client reauthentication-period to set the idle period before client reauthentication.

Use undo wlan client reauthentication-period to restore the default.

Syntax

wlan client reauthentication-period [ period-value ]

undo wlan client reauthentication-period

Default

The idle period is 10 seconds.

Views

System view

Predefined user roles

network-admin

Parameters

period-value: Specifies the idle period in the range of 1 to 3600 seconds.

Usage guidelines

When URL redirection for WLAN MAC authentication is enabled, an AP redirects clients whose information is not recorded on the RADIUS server to the specified URL for Web authentication. Clients passing Web authentication are logged off and must perform MAC reauthentication to come online. However, MAC reauthentication fails if the IP addresses assigned to the clients have not expired.

Perform this task to add these clients to the dynamic blacklist for the specified idle period after they pass Web authentication to reduce reauthentication failures.

Examples

# Set the idle period before client reauthentication to 100 seconds.

<Sysname> system-view

[Sysname] wlan client reauthentication-period 100

wlan dynamic-blacklist lifetime

Use wlan dynamic-blacklist lifetime to set the aging time for dynamic blacklist entries.

Use undo wlan dynamic-blacklist lifetime to restore the default.

Syntax

wlan dynamic-blacklist lifetime lifetime

undo wlan dynamic-blacklist lifetime

Default

The aging time is 300 seconds for dynamic blacklist entries.

Views

System view

Predefined user roles

network-admin

Parameters

lifetime: Specifies the aging time in the range of 1 to 3600 seconds.

Usage guidelines

The configured aging time takes effect only on entries added to the dynamic blacklist after this command is executed.

The aging time for dynamic blacklist entries only applies to rogue client entries.

Examples

# Set the aging time for dynamic blacklist entries to 3600 seconds.

<Sysname> system-view

[Sysname] wlan dynamic-blacklist lifetime 3600

wlan link-test

Use wlan link-test to test wireless link quality.

Syntax

wlan link-test mac-address

Views

Any view

Predefined user roles

network-admin

Parameters

mac-address: Specifies the client MAC address in the H-H-H format.

Usage guidelines

Wireless link quality detection enables an AP to test the quality of the link to a wireless client. The AP sends empty data frames to the client at each supported rate. Then it calculates link quality information such as RSSI, packet retransmissions, and RTT based on the responses from the client.

The timeout timer for wireless link quality detection is 10 seconds. If wireless link detection is not completed within the timeout timer, test results cannot be obtained.

Examples

# Test the quality of the wireless link to the client with MAC address 60a4-4cda-eff0.

<Sysname> wlan link-test 60a4-4cda-eff0

Testing link to 60a4-4cda-eff0. Press CTRL + C to break.

                              Link Status

-----------------------------------------------------------------------

MAC address: 60a4-4cda-eff0

-----------------------------------------------------------------------

VHT-MCS  Rate(Mbps)  Tx packets  Rx packets  RSSI   Retries RTT(ms)

-----------------------------------------------------------------------

NSS = 1

-----------------------------------------------------------------------

 0       32.5        5           5           54     0       0

 1       65          5           5           51     0       0

 2       97.5        5           5           49     0       0

 3       130         5           5           47     0       0

 4       195         5           5           45     0       0

 5       260         5           5           45     0       0

 6       292.5       5           5           44     0       0

 7       325         5           5           44     0       0

 8       390         5           5           44     0       0

 9       433.3       5           5           43     0       0

-----------------------------------------------------------------------

NSS = 2

-----------------------------------------------------------------------

 0       65          5           5           44     0       0

 1       130         5           5           44     0       0

 2       195         5           5           44     0       0

 3       260         5           5           44     0       0

 4       390         5           5           44     0       0

 5       520         5           5           44     0       0

 6       585         5           5           43     0       0

 7       650         5           5           43     0       0

 8       780         5           5           43     0       0

 9       866.7       5           5           43     0       0

# Test the quality of the wireless link to the client with MAC address 60a4-4cda-eff0.

<Sysname> wlan link-test 784f-43b6-077c

Testing link to 784f-43b6-077c. Press CTRL + C to break.

                              Link Status

-----------------------------------------------------------------------

MAC address: 784f-43b6-077c

-----------------------------------------------------------------------

MCS     Rate(Mbps)  Tx packets  Rx packets  RSSI   Retries  RTT(ms)

-----------------------------------------------------------------------

0       6.5         5           5           54     0        0

1       13          5           5           51     0        0

2       19.5        5           5           49     0        0

3       26          5           5           47     0        0

4       39          5           5           45     0        0

5       52          5           5           45     0        0

6       58.5        5           5           44     0        0

7       72.2        5           5           44     0        0

8       13          5           5           44     0        0

9       26          5           5           43     0        0

10       39         5           5           44     0        0

11       52         5           5           44     0        0

12       78         5           5           44     0        0

13       104        5           5           44     0        0

14       117        5           5           44     0        0

15       144.4      5           5           44     11       0

-----------------------------------------------------------------------

Table 20 Command output

Field

Description

No./MCS/VHT-MCS

·     No.—Rate number for link quality test on 802.11a, 802.11b, or 802.11g clients.

·     MCS—MCS index for link quality test on 802.11n clients.

·     VHT-MCS—VHT-MCS index for link quality test on 802.11ac clients.

Rate(Mbps)

Rate at which the AP sends wireless link quality detection frames.

Tx packets

Number of wireless link quality detection frames sent by the AP.

Rx packets

Number of responses received by the AP.

RSSI

RSSI of the client detected by the AP.

Retries

Number of wireless link quality retransmission frames sent by the AP.

RTT(ms)

Round trip time for link quality test frames from the AP to the client.

NSS

Number of spatial streams for link quality test on 802.11n or 802.11ac clients.

wlan nas-port-id format

Use wlan nas-port-id format to set the format of NAS port IDs for wireless clients.

Use undo wlan nas-port-id format to restore the default.

Syntax

wlan nas-port-id format { 2 | 4 }

undo wlan nas-port-id format

Default

Clients use format 2 to generate NAS port IDs.

Views

System view

Predefined user roles

network-admin

Parameters

2: Specifies the SlotID00IfNOVlanID format.

·     SlotID—Slot ID for client access, a string of two characters.

·     IfNO—Interface number for client access, a string of three characters.

·     VlanID—VLAN ID for client access, a string of nine characters.

4: Specifies the slot=**;subslot=**;port=**;vlanid=**;vlanid2=** format. The vlanid2 field is available only for clients accessing the WLAN through an interface configured with VLAN termination.

Usage guidelines

802.1X and MAC-authenticated clients provide NAS port IDs in the specified format in RADIUS packets.

Examples

# Set the NAS port ID format to format 4.

<Sysname> system-view

[Sysname] wlan nas-port-id format 4

wlan service-template

Use wlan service-template to create a service template and enter its view, or enter the view of an existing service template.

Use undo wlan service-template to delete a service template.

Syntax

wlan service-template service-template-name

undo wlan service-template service-template-name

Default

No service template exists.

Views

System view

Predefined user roles

network-admin

Parameters

service-template-name: Specifies a service template by its name, a case-insensitive string of 1 to 63 characters.

Usage guidelines

You cannot delete a service template that has been bound to a radio.

Examples

# Create service template service1 and enter its view.

<Sysname> system-view

[Sysname] wlan service-template service1

wlan static-blacklist mac-address

Use wlan static-blacklist mac-address to add a client to the static blacklist.

Use undo wlan static-blacklist mac-address to remove a client from the static blacklist.

Syntax

wlan static-blacklist mac-address mac-address

undo wlan static-blacklist [ mac-address mac-address ]

Default

No clients exist in the static blacklist.

Views

System view

Predefined user roles

network-admin

Parameters

mac-address mac-address: Specifies a client by its MAC address in the format of H-H-H.

Usage guidelines

If you add an online client to the static blacklist, the command logs off the client.

You cannot add a client to both the whitelist and the static blacklist.

The undo form of the command removes all clients from the static blacklist if you do not specify the mac-address mac-address option.

Do not add multicast or broadcast MAC addresses to the static blacklist.

Examples

# Add MAC address 001c-f0bf-9c92 to the static blacklist.

<Sysname> system-view

[Sysname] wlan static-blacklist mac-address 001c-f0bf-9c92

Related commands

display wlan blacklist

wlan web-server api-path

Use wlan web-server api-path to specify the path of the Web server to which client information is reported.

Use undo wlan web-server api-path to restore the default.

Syntax

wlan web-server api-path path

undo wlan web-server api-path

Default

The path of the Web server is not specified.

Views

System view

Predefined user roles

network-admin

Parameters

path: Specifies a path, a case-sensitive string of 1 to 256 characters.

Usage guidelines

The Web server accepts client information only when the server's host name, port number, and path are specified.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Specify the path of the Web server as /wlan/dev-cfg.

<Sysname> system-view

[Sysname] wlan web-server api-path /wlan/dev-cfg

Related commands

wlan web-server host

wlan web-server max-client-entry

wlan web-server host

Use wlan web-server host to specify the host name and port number of the Web server to which client information is reported.

Use undo wlan web-server host to restore the default.

Syntax

wlan web-server host host-name port port-number

undo wlan web-server host

Default

The host name and port number of the Web server are not specified.

Views

System view

Predefined user roles

network-admin

Parameters

host host-name: Specifies a host name, a case-insensitive string of 3 to 127 characters that can contain letters, digits, hyphens (-), underscores (_), and dots (.).

port port-number: Specifies a port number in the range of 1 to 65534.

Usage guidelines

The Web server accepts client information only when the server's host name, port number, and path are specified.

Client information changes are reported to the Web server in real time.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Specify the host name and port number of the Web server as www.abc.com and 668, respectively.

<Sysname> system-view

[Sysname] wlan web-server host www.abc.com port 668

Related commands

wlan web-server api-path

wlan web-server max-client-entry

wlan web-server max-client-entry

Use wlan web-server max-client-entry to set the maximum number of client entries that can be reported at a time.

Use undo wlan web-server max-client-entry to restore the default.

Syntax

wlan web-server max-client-entry number

undo wlan web-server max-client-entry

Default

A maximum of ten client entries can be reported at a time.

Views

System view

Predefined user roles

network-admin

Parameters

number: Specifies a maximum number of client entries that can be reported at a time, in the range of 1 to 25.

Examples

# Set the maximum of client entries that can be reported at a time to 12.

<Sysname> system-view

[Sysname] wlan web-server max-client-entry 12

Related commands

wlan web-server api-path

wlan web-server host

wlan whitelist mac-address

Use wlan whitelist mac-address to add a client to the whitelist.

Use undo wlan whitelist mac-address to remove a client from the whitelist.

Syntax

wlan whitelist mac-address mac-address

undo wlan whitelist [ mac-address mac-address ]

Default

No clients exist in the whitelist.

Views

System view

Predefined user roles

network-admin

Parameters

mac-address mac-address: Specifies a client by its MAC address in the format of H-H-H.

Usage guidelines

When you add the first client to the whitelist, the system asks you whether to disconnect all online clients. Enter Y at the prompt to configure the whitelist.

If you remove an online client from the whitelist, the command logs off the client. If you remove all clients from the whitelist, online clients will not be logged off.

You cannot add a client to both the whitelist and the static blacklist.

The undo form of the command removes all clients from the whitelist if you do not specify the mac-address mac-address option.

Do not add multicast or broadcast MAC addresses to the whitelist.

Examples

# Add MAC address 001c-f0bf-9c92 to the whitelist.

<Sysname> system-view

[Sysname] wlan whitelist mac-address 001c-f0bf-9c92

This command will disconnect all clients. Continue? [Y/N]:

Related commands

display wlan whitelist