00-About the S12500X-AF & S12500-X & S9800 CR

HomeSupportResource CenterReference GuidesCommand ReferencesH3C S12500X-AF & S12500-X & S9800 Switch Series Command References(R27xx)-6W10500-About the S12500X-AF & S12500-X & S9800 CR
Table of Contents
Related Documents

About the H3C S12500X-AF & S12500-X & S9800 command references

CAUTION

CAUTION:

For information about modules supported by software Release 2710 and later, see the release notes for H3C S12500X-AF & S12500-X & S9800 Release 2710 and later.

 

All commands on the device are declared.

The H3C S12500X-AF & S12500-X & S9800 command references describe the commands and command syntax options available for the H3C S12500X-AF & S12500-X & S9800 Switch Series running Release 2710 and later.

 

IMPORTANT

IMPORTANT:

The debugging and diagnostic commands on the device are used only by the professional maintenance personnel for network fault diagnosis. If necessary, contact H3C Support to obtain the related manuals.

 

Command reference

Content

Fundamentals Command Reference

Covers the commands for logging in to and setting up the device.

This command reference includes:

·     CLI (command privilege settings and CLI management commands).

·     RBAC.

·     Logging in to the device.

·     FTP and TFTP.

·     File system management.

·     Configuration file management.

·     Software upgrade.

·     ISSU.

·     Device management.

·     Tcl.

·     Python.

·     License management.

·     Preprovisioning.

Virtual Technologies Command Reference

Covers the commands for configuring IRF and MDC.

Layer 2—LAN Switching Command Reference

Covers the commands for configuring Layer 2 technologies and features in a LAN switched network.

This command reference includes:

·     Ethernet interface.

·     Loopback, null, and inloopback interfaces.

·     Bulk interface configuration.

·     MAC address table and MAC Information.

·     Ethernet link aggregation.

·     Port isolation.

·     Spanning tree.

·     Loop detection.

·     VLAN (including VLAN, super VLAN, and private VLAN).

·     MVRP.

·     VLAN mapping.

·     LLDP.

·     Service loopback group.

·     Cut-through forwarding.

·     DRNI.

Layer 3—IP Services Command Reference

Covers the commands for configuring and managing IP addressing (including static and dynamic IPv4 and IPv6 address assignment), network performance optimization, ARP, and interoperation between IPv4 and IPv6.

This command reference includes:

·     ARP (including gratuitous ARP, proxy ARP, ARP snooping, ARP fast-reply, and ARP direct route advertisement).

·     IP addressing.

·     DHCP.

·     DNS and DDNS.

·     Basic IP forwarding and load sharing.

·     Fast forwarding.

·     Adjacency table.

·     IRDP.

·     IP performance optimization.

·     UDP helper.

·     IPv6 basics.

·     DHCPv6.

·     IPv6 fast forwarding.

·     Tunneling.

·     GRE.

·     HTTP redirect.

Layer 3—IP Routing Command Reference

Covers the commands for configuring routes for IPv4 and IPv6 networks of different sizes, route filtering, route control, and policy based routing.

This command reference includes:

·     Basic IP routing.

·     Static routing.

·     RIP.

·     OSPF.

·     IS-IS.

·     BGP.

·     Policy-based routing.

·     IPv6 static routing.

·     RIPng.

·     OSPFv3.

·     IPv6 policy-based routing.

·     Routing policy.

IP Multicast Command Reference

Covers the commands for Layer 2 IPv4 multicast protocols (including IGMP snooping and multicast VLAN), Layer 3 IPv4 multicast protocols (including IGMP and PIM), Layer 2 IPv6 multicast protocols (including MLD snooping), and Layer 3 IPv6 multicast protocols (including MSDP).

This command reference includes:

·     IGMP snooping.

·     PIM snooping.

·     Multicast VLAN.

·     Multicast routing and forwarding.

·     IGMP.

·     PIM.

·     MSDP.

·     Multicast VPN.

·     MLD snooping.

·     IPv6 multicast VLAN.

·     MLD.

·     IPv6 multicast routing and forwarding.

·     IPv6 PIM snooping.

·     IPv6 PIM.

MPLS Command Reference

Covers the MPLS commands.

This command reference includes:

·     Basic MPLS.

·     Static LSP.

·     LDP.

·     MPLS TE.

·     Static CRLSP.

·     RSVP.

·     Tunnel policy.

·     MPLS L3VPN.

·     MPLS L2VPN.

·     VPLS.

·     MPLS OAM.

·     MCE and IPv6 MCE.

·     Static SR over MPLS.

ACL and QoS Command Reference

Covers the commands for classifying traffic with ACLs, and allocating network resources and managing congestions with QoS technologies to improve network performance and network use efficiency.

This command reference includes:

·     ACL.

·     QoS (including QoS policy, priority mapping, GTS and rate limit, congestion management, congestion avoidance, aggregate CAR, queue-based accounting, and QPPB).

·     Time range.

·     Data buffer.

·     MPLS QoS.

Security Command Reference

Covers security feature commands.

This command reference includes:

·     AAA.

·     Password control.

·     Keychain.

·     Public key management.

·     PKI.

·     IPsec, IKE, and IKEv2.

·     SSH.

·     SSL.

·     Object group.

·     Attack detection and prevention.

·     TCP attack prevention.

·     IP source guard.

·     ARP attack protection.

·     ND attack defense.

·     uRPF.

·     FIPS.

·     MACsec.

·     Crypto engine.

High Availability Command Reference

Covers high availability commands for managing failure detection and failover. Failure detection technologies focus on fault detection and isolation. Failover technologies focus on network recovery.

This command reference includes:

·     Ethernet OAM.

·     CFD.

·     DLDP.

·     RRPP.

·     ERPS.

·     Smart Link.

·     Monitor Link.

·     VRRP.

·     BFD.

·     Track.

·     Process placement.

·     Reth interface and redundancy group.

Network Management and Monitoring Command Reference

Covers the commands that help you manage and monitor your network, for example, manage system events, collect traffic statistics, sample packets, assess network performance, and test network connectivity.

This command reference includes:

·     System maintenance and debugging (ping, tracert, and system debugging).

·     NQA.

·     NTP and SNTP.

·     SNMP.

·     RMON.

·     Event MIB.

·     NETCONF.

·     CWMP.

·     EAA.

·     Process monitoring and maintenance.

·     Sampler.

·     Mirroring (including both port and traffic mirroring).

·     NetStream.

·     IPv6 NetStream.

·     sFlow.

·     Information center.

·     GOLD.

·     Packet capture.

·     VCF fabric.

FC and FCoE Command Reference

Covers the commands for configuring FC and FCoE.

OpenFlow Command Reference

Covers the commands for configuring OpenFlow.

VXLAN Command Reference

Covers the commands for configuring VXLAN.

EVPN Command Reference

Covers the commands for configuring EVPN.

 

 

NOTE:

Except for the above listed commands, the device has some commands that are not supported in the current software version. You can view and enter these commands, but the device does not support the features configured or displayed by using these commands.