H3C S6805 & S6850 & S9850 & S9820 Switch Series System Log Messages Reference-Release 66xx-6W100

HomeSupportResource CenterH3C S6805 & S6850 & S9850 & S9820 Switch Series System Log Messages Reference-Release 66xx-6W100

H3C S6805 & S6850 & S9850 & S9820 Switch Series

System Log Messages Reference

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Document version: 6W100-20200409

 

Copyright © 2020 New H3C Technologies Co., Ltd. All rights reserved.

No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New H3C Technologies Co., Ltd.

Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this document are the property of their respective owners.

The information in this document is subject to change without notice.

 


Contents

Introduction· 1

System log message format 1

Managing and obtaining system log messages· 3

Obtaining log messages from the console terminal 4

Obtaining log messages from a monitor terminal 4

Obtaining log messages from the log buffer 4

Obtaining log messages from the log file· 4

Obtaining log messages from a log host 4

Software module list 5

Using this document 9

AAA messages· 9

AAA_FAILURE· 10

AAA_LAUNCH· 10

AAA_SUCCESS· 11

ACL messages· 11

ACL_ACCELERATE_NO_RES· 11

ACL_ACCELERATE_NONCONTIGUOUSMASK· 12

ACL_ACCELERATE_NOT_SUPPORT· 12

ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP· 12

ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG·· 13

ACL_ACCELERATE_UNK_ERR· 13

ACL_IPV6_STATIS_INFO·· 13

ACL_NO_MEM·· 14

ACL_STATIS_INFO·· 14

ANCP messages· 14

ANCP_INVALID_PACKET· 15

APMGR messages· 15

APMGR_AC_MEM_ALERT· 15

APMGR_ADD_AP_FAIL· 16

APMGR_ADDBAC_INFO·· 16

APMGR_AP_OFFLINE· 16

APMGR_AP_ONLINE· 17

APMGR_CWC_IMG_DOWNLOAD_COMPLETE· 17

APMGR_CWC_IMG_DOWNLOAD_START· 17

APMGR_CWC_IMG_NO_ENOUGH_SPACE· 18

APMGR_CWC_LOCAL_AC_DOWN· 18

APMGR_CWC_LOCAL_AC_UP· 19

APMGR_CWC_REBOOT· 19

APMGR_CWC_RUN_DOWNLOAD_COMPLETE· 19

APMGR_CWC_RUN_DOWNLOAD_START· 20

APMGR_CWC_RUN_NO_ENOUGH_SPACE· 20

APMGR_CWC_TUNNEL_DOWN· 21

APMGR_CWC_TUNNEL_UP· 21

APMGR_CWS_IMG_DOWNLOAD_COMPLETE· 22

APMGR_CWS_IMG_DOWNLOAD_START· 22

APMGR_CWS_LOCAL_AC_DOWN· 23

APMGR_CWS_LOCAL_AC_UP· 23

APMGR_CWS_RUN_DOWNLOAD_COMPLETE· 24

APMGR_CWS_RUN_DOWNLOAD_START· 24

APMGR_CWS_TUNNEL_DOWN· 25

APMGR_CWS_TUNNEL_UP· 25

APMGR_DELBAC_INFO·· 26

APMGR_LOCAL_AC_OFFLINE· 26

APMGR_LOCAL_AC_ONLINE· 26

ARP messages· 26

ARP_ACTIVE_ACK_NO_REPLY· 27

ARP_ACTIVE_ACK_NOREQUESTED_REPLY· 27

ARP_BINDRULETOHW_FAILED· 28

ARP_DETECTION_LOG·· 29

ARP_DUPLICATE_IPADDR_DETECT· 29

ARP_DYNAMIC· 30

ARP_DYNAMIC_IF· 30

ARP_DYNAMIC_SLOT· 31

ARP_ENTRY_CONFLICT· 32

ARP_HOST_IP_CONFLICT· 32

ARP_LOCALPROXY_ENABLE_FAILED· 33

ARP_RATE_EXCEEDED· 33

ARP_RATELIMIT_NOTSUPPORT· 34

ARP_SENDER_IP_INVALID· 34

ARP_SENDER_MAC_INVALID· 35

ARP_SENDER_SMACCONFLICT· 35

ARP_SENDER_SMACCONFLICT_VSI 36

ARP_SRC_MAC_FOUND_ATTACK· 36

ARP_SUP_ENABLE_FAILED· 37

ARP_TARGET_IP_INVALID· 37

ARP_THRESHOLD_REACHED· 37

ARP_USER_DUPLICATE_IPADDR_DETECT· 38

ARP_USER_MOVE_DETECT· 39

DUPIFIP· 39

DUPIP· 40

DUPVRRPIP· 40

ATK messages· 40

ATK_ICMP_ADDRMASK_REQ·· 41

ATK_ICMP_ADDRMASK_REQ_RAW·· 42

ATK_ICMP_ADDRMASK_REQ_RAW_SZ· 43

ATK_ICMP_ADDRMASK_REQ_SZ· 44

ATK_ICMP_ADDRMASK_RPL· 45

ATK_ICMP_ADDRMASK_RPL_RAW·· 46

ATK_ICMP_ADDRMASK_RPL_RAW_SZ· 47

ATK_ICMP_ADDRMASK_RPL_SZ· 48

ATK_ICMP_ECHO_REQ·· 49

ATK_ICMP_ECHO_REQ_RAW·· 50

ATK_ICMP_ECHO_REQ_RAW_SZ· 51

ATK_ICMP_ECHO_REQ_SZ· 52

ATK_ICMP_ECHO_RPL· 53

ATK_ICMP_ECHO_RPL_RAW·· 54

ATK_ICMP_ECHO_RPL_RAW_SZ· 55

ATK_ICMP_ECHO_RPL_SZ· 56

ATK_ICMP_FLOOD· 57

ATK_ICMP_FLOOD_SZ· 57

ATK_ICMP_INFO_REQ·· 58

ATK_ICMP_INFO_REQ_RAW·· 59

ATK_ICMP_INFO_REQ_RAW_SZ· 60

ATK_ICMP_INFO_REQ_SZ· 61

ATK_ICMP_INFO_RPL· 62

ATK_ICMP_INFO_RPL_RAW·· 63

ATK_ICMP_INFO_RPL_RAW_SZ· 64

ATK_ICMP_INFO_RPL_SZ· 65

ATK_ICMP_LARGE· 66

ATK_ICMP_LARGE_RAW·· 66

ATK_ICMP_LARGE_RAW_SZ· 67

ATK_ICMP_LARGE_SZ· 68

ATK_ICMP_PARAPROBLEM·· 69

ATK_ICMP_PARAPROBLEM_RAW·· 70

ATK_ICMP_PARAPROBLEM_RAW_SZ· 71

ATK_ICMP_PARAPROBLEM_SZ· 72

ATK_ICMP_PINGOFDEATH· 73

ATK_ICMP_PINGOFDEATH_RAW·· 74

ATK_ICMP_PINGOFDEATH_RAW_SZ· 75

ATK_ICMP_PINGOFDEATH_SZ· 76

ATK_ICMP_REDIRECT· 77

ATK_ICMP_REDIRECT_RAW·· 78

ATK_ICMP_REDIRECT_RAW_SZ· 79

ATK_ICMP_REDIRECT_SZ· 80

ATK_ICMP_SMURF· 81

ATK_ICMP_SMURF_RAW·· 82

ATK_ICMP_SMURF_RAW_SZ· 83

ATK_ICMP_SMURF_SZ· 84

ATK_ICMP_SOURCEQUENCH· 85

ATK_ICMP_SOURCEQUENCH_RAW·· 86

ATK_ICMP_SOURCEQUENCH_RAW_SZ· 87

ATK_ICMP_SOURCEQUENCH_SZ· 88

ATK_ICMP_TIMEEXCEED· 89

ATK_ICMP_TIMEEXCEED_RAW·· 90

ATK_ICMP_TIMEEXCEED_RAW_SZ· 91

ATK_ICMP_TIMEEXCEED_SZ· 92

ATK_ICMP_TRACEROUTE· 93

ATK_ICMP_TRACEROUTE_RAW·· 94

ATK_ICMP_TRACEROUTE_RAW_SZ· 94

ATK_ICMP_TRACEROUTE_SZ· 95

ATK_ICMP_TSTAMP_REQ·· 96

ATK_ICMP_TSTAMP_REQ_RAW·· 97

ATK_ICMP_TSTAMP_REQ_RAW_SZ· 98

ATK_ICMP_TSTAMP_REQ_SZ· 99

ATK_ICMP_TSTAMP_RPL· 100

ATK_ICMP_TSTAMP_RPL_RAW·· 101

ATK_ICMP_TSTAMP_RPL_RAW_SZ· 102

ATK_ICMP_TSTAMP_RPL_SZ· 103

ATK_ICMP_TYPE· 104

ATK_ICMP_TYPE_RAW·· 105

ATK_ICMP_TYPE_RAW_SZ· 106

ATK_ICMP_TYPE_SZ· 107

ATK_ICMP_UNREACHABLE· 108

ATK_ICMP_UNREACHABLE_RAW·· 109

ATK_ICMP_UNREACHABLE_RAW_SZ· 110

ATK_ICMP_UNREACHABLE_SZ· 111

ATK_ICMPV6_DEST_UNREACH· 112

ATK_ICMPV6_DEST_UNREACH_RAW·· 113

ATK_ICMPV6_DEST_UNREACH_RAW_SZ· 113

ATK_ICMPV6_DEST_UNREACH_SZ· 114

ATK_ICMPV6_ECHO_REQ·· 115

ATK_ICMPV6_ECHO_REQ_RAW·· 116

ATK_ICMPV6_ECHO_REQ_RAW_SZ· 116

ATK_ICMPV6_ECHO_REQ_SZ· 117

ATK_ICMPV6_ECHO_RPL· 118

ATK_ICMPV6_ECHO_RPL_RAW·· 119

ATK_ICMPV6_ECHO_RPL_RAW_SZ· 119

ATK_ICMPV6_ECHO_RPL_SZ· 120

ATK_ICMPV6_FLOOD· 121

ATK_ICMPV6_FLOOD_SZ· 121

ATK_ICMPV6_GROUPQUERY· 122

ATK_ICMPV6_GROUPQUERY_RAW·· 123

ATK_ICMPV6_GROUPQUERY_RAW_SZ· 123

ATK_ICMPV6_GROUPQUERY_SZ· 124

ATK_ICMPV6_GROUPREDUCTION· 125

ATK_ICMPV6_GROUPREDUCTION_RAW·· 126

ATK_ICMPV6_GROUPREDUCTION_RAW_SZ· 126

ATK_ICMPV6_GROUPREDUCTION_SZ· 127

ATK_ICMPV6_GROUPREPORT· 128

ATK_ICMPV6_GROUPREPORT_RAW·· 129

ATK_ICMPV6_GROUPREPORT_RAW_SZ· 129

ATK_ICMPV6_GROUPREPORT_SZ· 130

ATK_ICMPV6_LARGE· 131

ATK_ICMPV6_LARGE_RAW·· 131

ATK_ICMPV6_LARGE_RAW_SZ· 132

ATK_ICMPV6_LARGE_SZ· 132

ATK_ICMPV6_PACKETTOOBIG·· 133

ATK_ICMPV6_PACKETTOOBIG_RAW·· 134

ATK_ICMPV6_PACKETTOOBIG_RAW_SZ· 134

ATK_ICMPV6_PACKETTOOBIG_SZ· 135

ATK_ICMPV6_PARAPROBLEM·· 136

ATK_ICMPV6_PARAPROBLEM_RAW·· 137

ATK_ICMPV6_PARAPROBLEM_RAW_SZ· 137

ATK_ICMPV6_PARAPROBLEM_SZ· 138

ATK_ICMPV6_TIMEEXCEED· 139

ATK_ICMPV6_TIMEEXCEED_RAW·· 140

ATK_ICMPV6_TIMEEXCEED_RAW_SZ· 140

ATK_ICMPV6_TIMEEXCEED_SZ· 141

ATK_ICMPV6_TRACEROUTE· 142

ATK_ICMPV6_TRACEROUTE_RAW·· 143

ATK_ICMPV6_TRACEROUTE_RAW_SZ· 144

ATK_ICMPV6_TRACEROUTE_SZ· 145

ATK_ICMPV6_TYPE· 146

ATK_ICMPV6_TYPE _RAW_SZ· 147

ATK_ICMPV6_TYPE_RAW·· 147

ATK_ICMPV6_TYPE_SZ· 148

ATK_IP_OPTION· 149

ATK_IP_OPTION_RAW·· 150

ATK_IP_OPTION_RAW_SZ· 151

ATK_IP_OPTION_SZ· 152

ATK_IP4_ACK_FLOOD· 153

ATK_IP4_ACK_FLOOD_SZ· 153

ATK_IP4_DIS_PORTSCAN· 154

ATK_IP4_DIS_PORTSCAN_SZ· 154

ATK_IP4_DNS_FLOOD· 155

ATK_IP4_DNS_FLOOD_SZ· 155

ATK_IP4_FIN_FLOOD· 156

ATK_IP4_FIN_FLOOD_SZ· 156

ATK_IP4_FRAGMENT· 157

ATK_IP4_FRAGMENT_RAW·· 158

ATK_IP4_FRAGMENT_RAW_SZ· 159

ATK_IP4_FRAGMENT_SZ· 160

ATK_IP4_HTTP_FLOOD· 161

ATK_IP4_HTTP_FLOOD_SZ· 161

ATK_IP4_IMPOSSIBLE· 162

ATK_IP4_IMPOSSIBLE_RAW·· 163

ATK_IP4_IMPOSSIBLE_RAW_SZ· 164

ATK_IP4_IMPOSSIBLE_SZ· 165

ATK_IP4_IPSWEEP· 166

ATK_IP4_IPSWEEP_SZ· 166

ATK_IP4_PORTSCAN· 167

ATK_IP4_PORTSCAN_SZ· 167

ATK_IP4_RST_FLOOD· 168

ATK_IP4_RST_FLOOD_SZ· 168

ATK_IP4_SYN_FLOOD· 169

ATK_IP4_SYN_FLOOD_SZ· 169

ATK_IP4_SYNACK_FLOOD· 170

ATK_IP4_SYNACK_FLOOD_SZ· 170

ATK_IP4_TCP_ALLFLAGS· 171

ATK_IP4_TCP_ALLFLAGS_RAW·· 172

ATK_IP4_TCP_ALLFLAGS_RAW_SZ· 172

ATK_IP4_TCP_ALLFLAGS_SZ· 173

ATK_IP4_TCP_FINONLY· 174

ATK_IP4_TCP_FINONLY_RAW·· 175

ATK_IP4_TCP_FINONLY_RAW_SZ· 175

ATK_IP4_TCP_FINONLY_SZ· 176

ATK_IP4_TCP_INVALIDFLAGS· 177

ATK_IP4_TCP_INVALIDFLAGS_RAW·· 178

ATK_IP4_TCP_INVALIDFLAGS_RAW_SZ· 179

ATK_IP4_TCP_INVALIDFLAGS_SZ· 180

ATK_IP4_TCP_LAND· 181

ATK_IP4_TCP_LAND_RAW·· 182

ATK_IP4_TCP_LAND_RAW_SZ· 183

ATK_IP4_TCP_LAND_SZ· 184

ATK_IP4_TCP_NULLFLAG·· 185

ATK_IP4_TCP_NULLFLAG_RAW·· 186

ATK_IP4_TCP_NULLFLAG_RAW_SZ· 186

ATK_IP4_TCP_NULLFLAG_SZ· 187

ATK_IP4_TCP_SYNFIN· 188

ATK_IP4_TCP_SYNFIN_RAW·· 189

ATK_IP4_TCP_SYNFIN_RAW_SZ· 189

ATK_IP4_TCP_SYNFIN_SZ· 190

ATK_IP4_TCP_WINNUKE· 191

ATK_IP4_TCP_WINNUKE_RAW·· 192

ATK_IP4_TCP_WINNUKE_RAW_SZ· 193

ATK_IP4_TCP_WINNUKE_SZ· 194

ATK_IP4_TEARDROP· 195

ATK_IP4_TEARDROP_RAW·· 196

ATK_IP4_TEARDROP_RAW_SZ· 197

ATK_IP4_TEARDROP_SZ· 198

ATK_IP4_TINY_FRAGMENT· 199

ATK_IP4_TINY_FRAGMENT_RAW·· 200

ATK_IP4_TINY_FRAGMENT_RAW_SZ· 201

ATK_IP4_TINY_FRAGMENT_SZ· 202

ATK_IP4_UDP_BOMB· 203

ATK_IP4_UDP_BOMB_RAW·· 204

ATK_IP4_UDP_BOMB_RAW_SZ· 205

ATK_IP4_UDP_BOMB_SZ· 206

ATK_IP4_UDP_FLOOD· 207

ATK_IP4_UDP_FLOOD_SZ· 207

ATK_IP4_UDP_FRAGGLE· 208

ATK_IP4_UDP_FRAGGLE_RAW·· 209

ATK_IP4_UDP_FRAGGLE_RAW_SZ· 210

ATK_IP4_UDP_FRAGGLE_SZ· 211

ATK_IP4_UDP_SNORK· 212

ATK_IP4_UDP_SNORK_RAW·· 213

ATK_IP4_UDP_SNORK_RAW_SZ· 214

ATK_IP4_UDP_SNORK_SZ· 215

ATK_IP6_ACK_FLOOD· 216

ATK_IP6_ACK_FLOOD_SZ· 216

ATK_IP6_DIS_PORTSCAN· 217

ATK_IP6_DIS_PORTSCAN_SZ· 217

ATK_IP6_DNS_FLOOD· 218

ATK_IP6_DNS_FLOOD_SZ· 218

ATK_IP6_FIN_FLOOD· 219

ATK_IP6_FIN_FLOOD_SZ· 219

ATK_IP6_FRAGMENT· 220

ATK_IP6_FRAGMENT_RAW·· 221

ATK_IP6_FRAGMENT_RAW_SZ· 222

ATK_IP6_FRAGMENT_SZ· 223

ATK_IP6_HTTP_FLOOD· 224

ATK_IP6_HTTP_FLOOD_SZ· 224

ATK_IP6_IMPOSSIBLE· 225

ATK_IP6_IMPOSSIBLE_RAW·· 226

ATK_IP6_IMPOSSIBLE_RAW_SZ· 227

ATK_IP6_IMPOSSIBLE_SZ· 228

ATK_IP6_IPSWEEP· 228

ATK_IP6_IPSWEEP_SZ· 229

ATK_IP6_PORTSCAN· 229

ATK_IP6_PORTSCAN_SZ· 230

ATK_IP6_RST_FLOOD· 230

ATK_IP6_RST_FLOOD_SZ· 231

ATK_IP6_SYN_FLOOD· 231

ATK_IP6_SYN_FLOOD_SZ· 232

ATK_IP6_SYNACK_FLOOD· 232

ATK_IP6_SYNACK_FLOOD_SZ· 233

ATK_IP6_TCP_ALLFLAGS· 233

ATK_IP6_TCP_ALLFLAGS_RAW·· 234

ATK_IP6_TCP_ALLFLAGS_RAW_SZ· 234

ATK_IP6_TCP_ALLFLAGS_SZ· 235

ATK_IP6_TCP_FINONLY· 236

ATK_IP6_TCP_FINONLY_RAW·· 236

ATK_IP6_TCP_FINONLY_RAW_SZ· 237

ATK_IP6_TCP_FINONLY_SZ· 238

ATK_IP6_TCP_INVALIDFLAGS· 239

ATK_IP6_TCP_INVALIDFLAGS_RAW·· 240

ATK_IP6_TCP_INVALIDFLAGS_RAW_SZ· 241

ATK_IP6_TCP_INVALIDFLAGS_SZ· 242

ATK_IP6_TCP_LAND· 243

ATK_IP6_TCP_LAND_RAW·· 243

ATK_IP6_TCP_LAND_RAW_SZ· 244

ATK_IP6_TCP_LAND_SZ· 245

ATK_IP6_TCP_NULLFLAG·· 246

ATK_IP6_TCP_NULLFLAG_RAW·· 246

ATK_IP6_TCP_NULLFLAG_RAW_SZ· 247

ATK_IP6_TCP_NULLFLAG_SZ· 248

ATK_IP6_TCP_SYNFIN· 249

ATK_IP6_TCP_SYNFIN_RAW·· 249

ATK_IP6_TCP_SYNFIN_RAW_SZ· 250

ATK_IP6_TCP_SYNFIN_SZ· 251

ATK_IP6_TCP_WINNUKE· 252

ATK_IP6_TCP_WINNUKE_RAW·· 252

ATK_IP6_TCP_WINNUKE_RAW_SZ· 253

ATK_IP6_TCP_WINNUKE_SZ· 254

ATK_IP6_UDP_FLOOD· 254

ATK_IP6_UDP_FLOOD_SZ· 255

ATK_IP6_UDP_FRAGGLE· 255

ATK_IP6_UDP_FRAGGLE_RAW·· 256

ATK_IP6_UDP_FRAGGLE_RAW_SZ· 256

ATK_IP6_UDP_FRAGGLE_SZ· 257

ATK_IP6_UDP_SNORK· 258

ATK_IP6_UDP_SNORK_RAW·· 258

ATK_IP6_UDP_SNORK_RAW_SZ· 259

ATK_IP6_UDP_SNORK_SZ· 260

ATK_IPOPT_ABNORMAL· 261

ATK_IPOPT_ABNORMAL_RAW·· 262

ATK_IPOPT_ABNORMAL_RAW_SZ· 263

ATK_IPOPT_ABNORMAL_SZ· 264

ATK_IPOPT_LOOSESRCROUTE· 265

ATK_IPOPT_LOOSESRCROUTE_RAW·· 266

ATK_IPOPT_LOOSESRCROUTE_RAW_SZ· 267

ATK_IPOPT_LOOSESRCROUTE_SZ· 268

ATK_IPOPT_RECORDROUTE· 269

ATK_IPOPT_RECORDROUTE_RAW·· 270

ATK_IPOPT_RECORDROUTE_RAW_SZ· 271

ATK_IPOPT_RECORDROUTE_SZ· 272

ATK_IPOPT_ROUTEALERT· 273

ATK_IPOPT_ROUTEALERT_RAW·· 274

ATK_IPOPT_ROUTEALERT_RAW_SZ· 275

ATK_IPOPT_ROUTEALERT_SZ· 276

ATK_IPOPT_SECURITY· 277

ATK_IPOPT_SECURITY_RAW·· 278

ATK_IPOPT_SECURITY_RAW_SZ· 279

ATK_IPOPT_SECURITY_SZ· 280

ATK_IPOPT_STREAMID· 281

ATK_IPOPT_STREAMID_RAW·· 282

ATK_IPOPT_STREAMID_RAW_SZ· 283

ATK_IPOPT_STREAMID_SZ· 284

ATK_IPOPT_STRICTSRCROUTE· 285

ATK_IPOPT_STRICTSRCROUTE_RAW·· 286

ATK_IPOPT_STRICTSRCROUTE_RAW_SZ· 287

ATK_IPOPT_STRICTSRCROUTE_SZ· 288

ATK_IPOPT_TIMESTAMP· 289

ATK_IPOPT_TIMESTAMP_RAW·· 290

ATK_IPOPT_TIMESTAMP_RAW_SZ· 291

ATK_IPOPT_TIMESTAMP_SZ· 292

ATK_IPV6_EXT_HEADER· 293

ATK_IPV6_EXT_HEADER_RAW·· 294

ATK_IPV6_EXT_HEADER_RAW_SZ· 294

ATK_IPV6_EXT_HEADER_SZ· 295

ATM·· 295

ATM_PVCDOWN· 296

ATM_PVCUP· 297

BFD messages· 297

BFD_CHANGE_FSM·· 297

BFD_REACHED_UPPER_LIMIT· 298

BGP messages· 298

BGP_EXCEED_ROUTE_LIMIT· 298

BGP_REACHED_THRESHOLD· 299

BGP_LOG_ROUTE_FLAP· 299

BGP_MEM_ALERT· 300

BGP_PEER_LICENSE_REACHED· 300

BGP_ROUTE_LICENSE_REACHED· 300

BGP_STATE_CHANGED· 301

BGP_STATE_CHANGED_REASON· 301

BLS messages· 302

BLS_ENTRY_ADD· 302

BLS_ENTRY_DEL· 302

BLS_IPV6_ENTRY_ADD· 303

BLS_IPV6_ENTRY_DEL· 303

CFD messages· 303

CFD_CROSS_CCM·· 304

CFD_ERROR_CCM·· 304

CFD_LOST_CCM·· 305

CFD_RECEIVE_CCM·· 305

CFGMAN messages· 306

CFGMAN_ARCHIVE_SCP_FAIL· 306

CFGMAN_CFGCHANGED· 306

CFGMAN_EXIT_FROM_CONFIGURE· 307

CFGMAN_OPTCOMPLETION· 307

CONNLMT messages· 308

CONNLMT_IPV4_OVERLOAD· 309

CONNLMT_IPV4_RECOVER· 310

CONNLMT_IPV6_OVERLOAD· 311

CONNLMT_IPV6_RECOVER· 312

DEV messages· 312

BOARD_INSERTED· 312

BOARD_REBOOT· 313

BOARD_REMOVED· 313

BOARD_STATE_FAULT· 313

BOARD_STATE_NORMAL· 314

BOARD_STATE_STARTING·· 314

CFCARD_INSERTED· 314

CFCARD_REMOVED· 315

CHASSIS_REBOOT· 315

DEV_CLOCK_CHANGE· 315

DEV_FAULT_TOOLONG·· 316

DYINGGASP· 316

FAN_ABSENT· 317

FAN_DIRECTION_NOT_PREFERRED· 317

FAN_FAILED· 318

FAN_RECOVERED· 318

MAD_DETECT· 319

POWER_ABSENT· 319

POWER_FAILED· 320

POWER_MONITOR_ABSENT· 320

POWER_MONITOR_FAILED· 321

POWER_MONITOR_RECOVERED· 321

POWER_RECOVERED· 322

RPS_ABSENT· 322

RPS_FAILED· 323

RPS_NORMAL· 323

SUBCARD_FAULT· 324

SUBCARD_INSERTED· 324

SUBCARD_REBOOT· 324

SUBCARD_REMOVED· 325

SYSTEM_REBOOT· 325

TEMPERATURE_ALARM·· 326

TEMPERATURE_LOW·· 327

TEMPERATURE_NORMAL· 328

TEMPERATURE_SHUTDOWN· 329

TEMPERATURE_WARNING·· 330

VCHK_VERSION_INCOMPATIBLE· 331

DHCP· 331

DHCP_NOTSUPPORTED· 331

DHCP_NORESOURCES· 331

DHCPR·· 332

DHCPR_SERVERCHANGE· 332

DHCPR_SWITCHMASTER· 332

DHCPS messages· 332

DHCPS_ALLOCATE_IP· 333

DHCPS_CONFLICT_IP· 333

DHCPS_EXTEND_IP· 334

DHCPS_FILE· 334

DHCPS_RECLAIM_IP· 334

DHCPS_VERIFY_CLASS· 335

DHCPS6 messages· 335

DHCPS6_ALLOCATE_ADDRESS· 335

DHCPS6_ALLOCATE_PREFIX· 336

DHCPS6_CONFLICT_ADDRESS· 336

DHCPS6_EXTEND_ADDRESS· 337

DHCPS6_EXTEND_PREFIX· 337

DHCPS6_FILE· 338

DHCPS6_RECLAIM_ADDRESS· 338

DHCPS6_RECLAIM_PREFIX· 339

DHCPSP4· 339

DHCPSP4_FILE· 339

DHCPSP6· 339

DHCPSP6_FILE· 340

DIAG messages· 340

CPU_MINOR_RECOVERY· 340

CPU_MINOR_THRESHOLD· 340

CPU_SEVERE_RECOVERY· 341

CPU_SEVERE_THRESHOLD· 341

MEM_ALERT· 342

MEM_BELOW_THRESHOLD· 343

MEM_EXCEED_THRESHOLD· 343

DLDP messages· 344

DLDP_AUTHENTICATION_FAILED· 344

DLDP_LINK_BIDIRECTIONAL· 344

DLDP_LINK_SHUTMODECHG·· 345

DLDP_LINK_UNIDIRECTIONAL· 345

DLDP_NEIGHBOR_AGED· 346

DLDP_NEIGHBOR_CONFIRMED· 346

DLDP_NEIGHBOR_DELETED· 347

DOT1X messages· 347

DOT1X_CONFIG_NOTSUPPORT· 347

DOT1X_LOGIN_FAILURE· 348

DOT1X_LOGIN_SUCC· 348

DOT1X_LOGIN_SUCC (in open mode) 349

DOT1X_LOGOFF· 349

DOT1X_LOGOFF (in open mode) 350

DOT1X_LOGOFF_ABNORMAL· 351

DOT1X_LOGOFF_ABNORMAL (in open mode) 352

DOT1X_MACBINDING_EXIST· 352

DOT1X_NOTENOUGH_EADFREEIP_RES· 353

DOT1X_NOTENOUGH_EADFREERULE_RES· 353

DOT1X_NOTENOUGH_EADMACREDIR_RES· 353

DOT1X_NOTENOUGH_EADPORTREDIR_RES· 354

DOT1X_NOTENOUGH_ENABLEDOT1X_RES· 354

DOT1X_PEXAGG_NOMEMBER_RES· 354

DOT1X_SMARTON_FAILURE· 355

DOT1X_UNICAST_NOT_EFFECTIVE· 355

DRNI 355

DRNI_AUTO-RECOVERY_TIMEOUT· 356

DRNI_GLBCHECK_CONSISTENCY· 356

DRNI_GLBCHECK_INCONSISTENCY· 356

DRNI_IFCHECK_CONSISTENCY· 357

DRNI_IFCHECK_INCONSISTENCY· 357

DRNI_IFEVENT_DR_BIND· 357

DRNI_IFEVENT_DR_GLOBALDOWN· 358

DRNI_IFEVENT_DR_GLOBALUP· 358

DRNI_IFEVENT_DR_NOSELECTED· 358

DRNI_IFEVENT_DR_PEER_NOSELECTED· 359

DRNI_IFEVENT_DR_PEER_SELECTED· 359

DRNI_IFEVENT_DR_SELECTED· 359

DRNI_IFEVENT_DR_UNBIND· 360

DRNI_IFEVENT_IPP_BIND· 360

DRNI_IFEVENT_IPP_DOWN· 360

DRNI_IFEVENT_IPP_UNBIND· 361

DRNI_IFEVENT_IPP_UP· 361

DRNI_IPP_BLOCK· 361

DRNI_IPP_UNBLOCK· 362

DRNI_KEEPALIVEINTERVAL_MISMATCH· 362

DRNI_KEEPALIVELINK_DOWN· 362

DRNI_KEEPALIVELINK_UP· 363

DRNI_SECONDARY_MADDOWN· 363

DRNI_SECONDARY_MADRECOVERY· 363

DRNI_SYSEVENT_DEVICEROLE_CHANGE· 364

DRNI_SYSEVENT_MAC_CHANGE· 364

DRNI_SYSEVENT_NUMBER_CHANGE· 365

DRNI_SYSEVENT_PRIORITY_CHANGE· 365

DRVPLAT· 365

Dev_FAILTURE· 365

EDEV messages· 367

ALARM_IN_REMOVED· 367

ALARM_IN_REPORTED· 368

EDEV_BOOTROM_UPDATE_FAILED· 368

EDEV_BOOTROM_UPDATE_SUCCESS· 368

EDEV_FAILOVER_GROUP_STATE_CHANGE· 369

ERPS messages· 369

ERPS_STATE_CHANGED· 369

ETH messages· 369

ETH_SET_MAC_FAILED· 370

ETHOAM messages· 370

ETHOAM_CONNECTION_FAIL_DOWN· 370

ETHOAM_CONNECTION_FAIL_TIMEOUT· 371

ETHOAM_CONNECTION_FAIL_UNSATISF· 371

ETHOAM_CONNECTION_SUCCEED· 371

ETHOAM_DISABLE· 372

ETHOAM_DISCOVERY_EXIT· 372

ETHOAM_ENABLE· 372

ETHOAM_ENTER_LOOPBACK_CTRLLED· 373

ETHOAM_ENTER_LOOPBACK_CTRLLING·· 373

ETHOAM_LOCAL_DYING_GASP· 373

ETHOAM_LOCAL_ERROR_FRAME· 374

ETHOAM_LOCAL_ERROR_FRAME_PERIOD· 374

ETHOAM_LOCAL_ERROR_FRAME_SECOND· 374

ETHOAM_LOCAL_ERROR_SYMBOL· 375

ETHOAM_LOCAL_LINK_FAULT· 375

ETHOAM_LOOPBACK_EXIT· 375

ETHOAM_LOOPBACK_EXIT_ERROR_STATU· 376

ETHOAM_LOOPBACK_NO_RESOURCE· 376

ETHOAM_LOOPBACK_NOT_SUPPORT· 376

ETHOAM_QUIT_LOOPBACK_CTRLLED· 377

ETHOAM_QUIT_LOOPBACK_CTRLLING·· 377

ETHOAM_REMOTE_CRITICAL· 377

ETHOAM_REMOTE_DYING_GASP· 378

ETHOAM_REMOTE_ERROR_FRAME· 378

ETHOAM_REMOTE_ERROR_FRAME_PERIOD· 378

ETHOAM_REMOTE_ERROR_FRAME_SECOND· 379

ETHOAM_REMOTE_ERROR_SYMBOL· 379

ETHOAM_REMOTE_EXIT· 379

ETHOAM_REMOTE_FAILURE_RECOVER· 380

ETHOAM_REMOTE_LINK_FAULT· 380

ETHOAM_NO_ENOUGH_RESOURCE· 380

ETHOAM_NOT_CONNECTION_TIMEOUT· 381

EVB messages· 381

EVB_AGG_FAILED· 381

EVB_LICENSE_EXPIRE· 381

EVB_VSI_OFFLINE· 382

EVB_VSI_ONLINE· 382

EVIISIS messages· 382

EVIISIS_LICENSE_EXPIRED· 382

EVIISIS_LICENSE_EXPIRED_TIME· 383

EVIISIS_LICENSE_UNAVAILABLE· 383

EVIISIS_NBR_CHG·· 384

FCLINK messages· 384

FCLINK_FDISC_REJECT_NORESOURCE· 384

FCLINK_FLOGI_REJECT_NORESOURCE· 385

FCOE messages· 385

FCOE_INTERFACE_NOTSUPPORT_FCOE· 385

FCOE_LAGG_BIND_ACTIVE· 386

FCOE_LAGG_BIND_DEACTIVE· 386

FCZONE messages· 386

FCZONE_DISTRIBUTE_FAILED· 387

FCZONE_HARDZONE_DISABLED· 387

FCZONE_HARDZONE_ENABLED· 388

FCZONE_ISOLATE_ALLNEIGHBOR· 388

FCZONE_ISOLATE_CLEAR_VSAN· 389

FCZONE_ISOLATE_CLEAR_ALLVSAN· 389

FCZONE_ISOLATE_NEIGHBOR· 389

FIB messages· 390

FIB_FILE· 390

FILTER messages· 390

FILTER_EXECUTION_ICMP· 391

FILTER_EXECUTION_ICMPV6· 392

FILTER_IPV4_EXECUTION· 393

FILTER_IPV6_EXECUTION· 394

FIPSNG messages· 394

FIPSNG_HARD_RESOURCE_NOENOUGH· 394

FIPSNG_HARD_RESOURCE_RESTORE· 395

FS messages· 395

FS_UNFORMATTED_PARTITION· 395

FTP messages· 395

FTP_ACL_DENY· 396

FTP_REACH_SESSION_LIMIT· 396

FTPD_AUTHOR_FAILED· 396

gRPC messages· 397

GRPC_LOGIN· 397

GRPC_LOGIN_FAILED· 397

GRPC_LOGOUT· 398

GRPC_SERVER_FAILED· 398

GRPC_SUBSCRIBE_EVENT_FAILED· 398

GRPC_RECEIVE_SUBSCRIPTION· 399

HA messages· 399

HA_BATCHBACKUP_FINISHED· 399

HA_BATCHBACKUP_STARTED· 399

HA_STANDBY_NOT_READY· 400

HA_STANDBY_TO_MASTER· 400

HQOS messages· 400

HQOS_DP_SET_FAIL· 400

HQOS_FP_SET_FAIL· 401

HQOS_POLICY_APPLY_FAIL· 401

HQOS_POLICY_APPLY_FAIL· 402

HTTPD messages· 402

HTTPD_CONNECT· 402

HTTPD_CONNECT_TIMEOUT· 403

HTTPD_DISCONNECT· 403

HTTPD_FAIL_FOR_ACL· 403

HTTPD_FAIL_FOR_ACP· 404

HTTPD_REACH_CONNECT_LIMIT· 404

IFNET messages· 404

IF_BUFFER_CONGESTION_OCCURRENCE· 405

IF_BUFFER_CONGESTION_CLEAR· 405

IF_JUMBOFRAME_WARN· 406

IF_LINKFLAP_DETECTED· 406

INTERFACE_NOTSUPPRESSED· 406

INTERFACE_SUPPRESSED· 407

LINK_UPDOWN· 407

PHY_UPDOWN· 407

PROTOCOL_UPDOWN· 408

TUNNEL_LINK_UPDOWN· 408

TUNNEL_PHY_UPDOWN· 408

VLAN_MODE_CHANGE· 409

IKE messages· 409

IKE_P1_SA_ESTABLISH_FAIL· 409

IKE_P2_SA_ESTABLISH_FAIL· 410

IKE_P2_SA_TERMINATE· 410

IKE_VERIFY_CERT_FAIL· 411

IMA· 412

IMA_ALLOCATE_FAILED· 412

IMA_DATA_ERROR· 413

IMA_FILE_HASH_FAILED· 413

IMA_RM_FILE_MISS· 413

IMA_RM_HASH_MISS· 414

IMA_TEMPLATE_ERROR· 414

IP6ADDR·· 414

IP6ADDR_CREATEADDRESS_ERROR· 415

IP6ADDR_FUNCTION_FAIL· 415

IP6FW·· 415

IPv6_MTU_SET_DRV_NOT_SUPPORT· 416

IPADDR messages· 416

IPADDR_HA_EVENT_ERROR· 417

IPADDR_HA_STOP_EVENT· 418

IPFW·· 418

IPFW_FAILURE· 418

IPv4_MTU_SET_DRV_NOT_SUPPORT· 419

IPSEC messages· 419

IPSEC_FAILED_ADD_FLOW_TABLE· 419

IPSEC_PACKET_DISCARDED· 420

IPSEC_SA_ESTABLISH· 420

IPSEC_SA_ESTABLISH_FAIL· 421

IPSEC_SA_INITINATION· 421

IPSEC_SA_TERMINATE· 422

IPSG messages· 422

IPSG_ADDENTRY_ERROR· 423

IPSG_ARP_LOCALMAC_CONFLICT· 424

IPSG_ARP_REMOTEMAC_CONFLICT· 424

IPSG_ADDEXCLUDEDVLAN_ERROR· 425

IPSG_DELENTRY_ERROR· 426

IPSG_DELEXCLUDEDVLAN_ERROR· 427

IPSG_MAC_CONFLICT· 427

IPSG_ND_LOCALMAC_CONFLICT· 428

IPSG_ND_REMOTEMAC_CONFLICT· 428

IRDP messages· 429

IRDP_EXCEED_ADVADDR_LIMIT· 429

IRF· 429

IRF_LINK_BLOCK· 429

IRF_LINK_DOWN· 430

IRF_LINK_UP· 430

IRF_MEMBERID_CONFLICT· 430

IRF_MERGE· 431

IRF_MERGE_NEED_REBOOT· 431

IRF_MERGE_NOT_NEED_REBOOT· 431

ISIS messages· 431

ISIS_LSP_CONFLICT· 432

ISIS_MEM_ALERT· 432

ISIS_NBR_CHG·· 433

ISSU messages· 433

ISSU_LOAD_FAILED· 433

ISSU_LOAD_SUCCESS· 434

ISSU_PROCESSWITCHOVER· 434

ISSU_ROLLBACKCHECKNORMAL· 434

L2PT messages· 434

L2PT_SET_MULTIMAC_FAILED· 435

L2PT_CREATE_TUNNELGROUP_FAILED· 435

L2PT_ADD_GROUPMEMBER_FAILED· 435

L2PT_ENABLE_DROP_FAILED· 436

L2TPv2 messages· 436

L2TPV2_TUNNEL_EXCEED_LIMIT· 436

L2TPV2_SESSION_EXCEED_LIMIT· 436

L2VPN messages· 437

L2VPN_ARP_MOBILITY_SUPPRESS (public instance) 437

L2VPN_ARP_MOBILITY_SUPPRESS (VPN instance) 437

L2VPN_ARP_MOBILITY_UNSUPPRESS (public instance) 438

L2VPN_ARP_MOBILITY_UNSUPPRESS (VPN instance) 438

L2VPN_MAC_MOBILITY_SUPPRESS· 439

L2VPN_MAC_MOBILITY_UNSUPPRESS· 439

L2VPN_BGPVC_CONFLICT_LOCAL· 440

L2VPN_BGPVC_CONFLICT_REMOTE· 440

L2VPN_HARD_RESOURCE_NOENOUGH· 441

L2VPN_HARD_RESOURCE_RESTORE· 441

L2VPN_LABEL_DUPLICATE· 441

L2VPN_MLAG_AC_CONFLICT· 442

LAGG messages· 442

LAGG_ACTIVE· 442

LAGG_AUTO_AGGREGATION· 443

LAGG_INACTIVE_AICFG·· 443

LAGG_INACTIVE_BFD· 444

LAGG_INACTIVE_CONFIGURATION· 444

LAGG_INACTIVE_DUPLEX· 445

LAGG_INACTIVE_HARDWAREVALUE· 445

LAGG_INACTIVE_IFCFG_DEFAULT· 446

LAGG_INACTIVE_IFCFG_LOOPPORT· 446

LAGG_INACTIVE_IFCFG_NONAGG·· 446

LAGG_INACTIVE_KEY_INVALID· 447

LAGG_INACTIVE_LOWER_LIMIT· 447

LAGG_INACTIVE_NODEREMOVE· 448

LAGG_INACTIVE_OPERSTATE· 448

LAGG_INACTIVE_PARTNER· 448

LAGG_INACTIVE_PARTNER_KEY_WRONG·· 449

LAGG_INACTIVE_PARTNER_MAC_WRONG·· 449

LAGG_INACTIVE_PARTNER_NONAGG·· 450

LAGG_INACTIVE_PARTNER_RDIRHANDLE· 450

LAGG_INACTIVE_PHYSTATE· 451

LAGG_INACTIVE_PORT_DEFAULT· 451

LAGG_INACTIVE_RDIRHANDLE· 452

LAGG_INACTIVE_REDUNDANCY· 452

LAGG_INACTIVE_RESOURCE_INSUFICIE· 453

LAGG_INACTIVE_SPEED· 453

LAGG_INACTIVE_STANDBY· 454

LAGG_INACTIVE_UPPER_LIMIT· 454

LAGG_SELECTPORT_INCONSISTENT· 455

LDP messages· 455

LDP_MPLSLSRID_CHG·· 455

LDP_SESSION_CHG·· 456

LDP_SESSION_GR· 457

LDP_SESSION_SP· 457

LLDP messages· 458

LLDP_CREATE_NEIGHBOR· 458

LLDP_DELETE_NEIGHBOR· 458

LLDP_LESS_THAN_NEIGHBOR_LIMIT· 459

LLDP_NEIGHBOR_AGE_OUT· 459

LLDP_NEIGHBOR_PROTECTION_BLOCK· 460

LLDP_NEIGHBOR_PROTECTION_DOWN· 460

LLDP_NEIGHBOR_PROTECTION_UNBLOCK· 461

LLDP_NEIGHBOR_PROTECTION_UP· 461

LLDP_PVID_INCONSISTENT· 462

LLDP_REACH_NEIGHBOR_LIMIT· 462

LOAD messages· 462

BOARD_LOADING·· 463

LOAD_FAILED· 463

LOAD_FINISHED· 463

LOGIN messages· 464

LOGIN_FAILED· 464

LOGIN_ INVALID_USERNAME_PWD· 464

LPDT messages· 464

LPDT_LOOPED· 465

LPDT_RECOVERED· 465

LPDT_VLAN_LOOPED· 465

LPDT_VLAN_RECOVERED· 466

LS messages· 466

LS_ADD_USER_TO_GROUP· 466

LS_AUTHEN_FAILURE· 467

LS_AUTHEN_SUCCESS· 467

LS_DEL_USER_FROM_GROUP· 467

LS_DELETE_PASSWORD_FAIL· 468

LS_PWD_ADDBLACKLIST· 468

LS_PWD_CHGPWD_FOR_AGEDOUT· 468

LS_PWD_CHGPWD_FOR_AGEOUT· 469

LS_PWD_CHGPWD_FOR_COMPOSITION· 469

LS_PWD_CHGPWD_FOR_FIRSTLOGIN· 469

LS_PWD_CHGPWD_FOR_LENGTH· 470

LS_PWD_FAILED2WRITEPASS2FILE· 470

LS_PWD_MODIFY_FAIL· 471

LS_PWD_MODIFY_SUCCESS· 471

LS_REAUTHEN_FAILURE· 472

LS_UPDATE_PASSWORD_FAIL· 472

LS_USER_CANCEL· 472

LS_USER_PASSWORD_EXPIRE· 473

LS_USER_ROLE_CHANGE· 473

LSPV messages· 473

LSPV_PING_STATIS_INFO·· 474

MAC messages· 474

MAC_DRIVER_ADD_ENTRY· 474

MAC_PROTOCOLPKT_NORES_GLOBAL· 475

MAC_PROTOCOLPKT_NORES_PORT· 475

MAC_PROTOCOLPKT_NORES_VLAN· 476

MAC_TABLE_FULL_GLOBAL· 476

MAC_TABLE_FULL_PORT· 476

MAC_TABLE_FULL_VLAN· 477

MAC_VLAN_LEARNLIMIT_NORESOURCE· 477

MAC_VLAN_LEARNLIMIT_NOTSUPPORT· 477

MACA messages· 477

MACA_ENABLE_NOT_EFFECTIVE· 478

MACA_LOGIN_FAILURE· 478

MACA_LOGIN_SUCC· 479

MACA_LOGIN_SUCC (in open mode) 479

MACA_LOGOFF· 480

MACA_LOGOFF (in open mode) 480

MACSEC messages· 480

MACSEC_MKA_KEEPALIVE_TIMEOUT· 481

MACSEC_MKA_PRINCIPAL_ACTOR· 481

MACSEC_MKA_SAK_REFRESH· 481

MACSEC_MKA_SESSION_REAUTH· 482

MACSEC_MKA_SESSION_SECURED· 482

MACSEC_MKA_SESSION_START· 483

MACSEC_MKA_SESSION_STOP· 483

MACSEC_MKA_SESSION_UNSECURED· 484

MBFD messages· 484

MBFD_TRACEROUTE_FAILURE· 484

MBUF messages· 485

MBUF_DATA_BLOCK_CREATE_FAIL· 485

MDC messages· 485

MDC_CREATE_ERR· 486

MDC_CREATE· 486

MDC_DELETE· 486

MDC_KERNEL_EVENT_TOOLONG·· 487

MDC_LICENSE_EXPIRE· 487

MDC_NO_FORMAL_LICENSE· 487

MDC_NO_LICENSE_EXIT· 488

MDC_OFFLINE· 488

MDC_ONLINE· 488

MDC_STATE_CHANGE· 489

MFIB messages· 489

MFIB_MEM_ALERT· 489

MGROUP messages· 489

MGROUP_APPLY_SAMPLER_FAIL· 490

MGROUP_RESTORE_CPUCFG_FAIL· 490

MGROUP_RESTORE_GROUP_FAIL· 491

MGROUP_RESTORE_IFCFG_FAIL· 491

MGROUP_SYNC_CFG_FAIL· 492

MPLS messages· 492

MPLS_HARD_RESOURCE_NOENOUGH· 492

MPLS_HARD_RESOURCE_RESTORE· 493

MTLK messages· 493

MTLK_UPLINK_STATUS_CHANGE· 493

NAT messages· 493

NAT_ADDR_BIND_CONFLICT· 494

NAT_FAILED_ADD_FLOW_RULE· 494

NAT_FAILED_ADD_FLOW_TABLE· 495

NAT_FLOW·· 496

NAT_SERVER_INVALID· 497

NAT_SERVICE_CARD_RECOVER_FAILURE· 498

ND messages· 498

ND_COMMONPROXY_ENABLE_FAILED· 499

ND_CONFLICT· 499

ND_DUPADDR· 499

ND_HOST_IP_CONFLICT· 500

ND_LOCALPROXY_ENABLE_FAILED· 500

ND_MAC_CHECK· 501

ND_NETWORKROUTE_DUPLICATE· 501

ND_RAGUARD_DROP· 502

ND_RATE_EXCEEDED· 502

ND_RATELIMIT_NOTSUPPORT· 503

ND_SET_PORT_TRUST_NORESOURCE· 503

ND_SET_VLAN_REDIRECT_NORESOURCE· 503

ND_USER_DUPLICATE_IPV6ADDR· 504

ND_USER_MOVE· 505

ND_USER_OFFLINE· 505

ND_USER_ONLINE· 506

NETCONF messages· 506

CLI 506

EDIT-CONFIG·· 507

NETCONF_MSG_DEL· 508

THREAD· 508

NQA messages· 508

NQA_LOG_UNREACHABLE· 508

NTP messages· 509

NTP_CLOCK_CHANGE· 509

NTP_LEAP_CHANGE· 509

NTP_SOURCE_CHANGE· 510

NTP_SOURCE_LOST· 510

NTP_STRATUM_CHANGE· 510

OAP messages· 511

OAP_CLIENT_DEREG·· 511

OAP_CLIENT_TIMEOUT· 511

OBJP messages· 511

OBJP_ACCELERATE_NO_RES· 512

OBJP_ACCELERATE_NOT_SUPPORT· 512

OBJP_ACCELERATE_UNK_ERR· 512

OFP messages· 512

OFP_ACTIVE· 513

OFP_ACTIVE_FAILED· 513

OFP_CONNECT· 513

OFP_FAIL_OPEN· 514

OFP_FLOW_ADD· 514

OFP_FLOW_ADD_ARP_FAILED· 514

OFP_FLOW_ADD_DUP· 515

OFP_FLOW_ADD_FAILED· 515

OFP_FLOW_ADD_FAILED· 516

OFP_FLOW_ADD_ND_FAILED· 516

OFP_FLOW_ADD_TABLE_MISS· 517

OFP_FLOW_ADD_TABLE_MISS_FAILED· 517

OFP_FLOW_DEL· 518

OFP_FLOW_DEL_L2VPN_DISABLE· 518

OFP_FLOW_DEL_TABLE_MISS· 519

OFP_FLOW_DEL_TABLE_MISS_FAILED· 519

OFP_FLOW_DEL_VXLAN_DEL· 520

OFP_FLOW_MOD· 520

OFP_FLOW_MOD_FAILED· 521

OFP_FLOW_MOD_TABLE_MISS· 521

OFP_FLOW_MOD_TABLE_MISS_FAILED· 522

OFP_FLOW_RMV_GROUP· 522

OFP_FLOW_RMV_HARDTIME· 522

OFP_FLOW_RMV_IDLETIME· 523

OFP_FLOW_RMV_METER· 523

OFP_FLOW_UPDATE_FAILED· 524

OFP_GROUP_ADD· 524

OFP_GROUP_ADD_FAILED· 525

OFP_GROUP_DEL· 525

OFP_GROUP_MOD· 526

OFP_GROUP_MOD_FAILED· 526

OFP_GROUP_REFRESH_FAILED· 527

OFP_GROUP_ROLLBACK_FAILED· 527

OFP_METER_ADD· 527

OFP_METER_ADD_FAILED· 528

OFP_METER_DEL· 528

OFP_METER_MOD· 529

OFP_METER_MOD_FAILED· 529

OFP_MISS_RMV_GROUP· 529

OFP_MISS_RMV_HARDTIME· 530

OFP_MISS_RMV_IDLETIME· 530

OFP_MISS_RMV_METER· 530

OFP_RADARDETECTION· 531

PORT_MOD· 532

OPENSRC (FreeRADIUS) messages· 533

HUP event 533

Process restart event 534

Process start event 534

User authentication· 535

OPTMOD messages· 537

BIAS_HIGH· 537

BIAS_LOW·· 538

BIAS_NORMAL· 538

CFG_ERR· 538

CHKSUM_ERR· 539

FIBER_SFP MODULE_INVALID· 539

FIBER_SFPMODULE_NOWINVALID· 539

IO_ERR· 540

MOD_ALM_OFF· 540

MOD_ALM_ON· 540

MODULE_IN· 541

MODULE_OUT· 541

PHONY_MODULE· 541

RX_ALM_OFF· 542

RX_ALM_ON· 542

RX_POW_HIGH· 542

RX_POW_LOW·· 543

RX_POW_NORMAL· 543

TEMP_HIGH· 543

TEMP_LOW·· 544

TEMP_NORMAL· 544

TX_ALM_OFF· 544

TX_ALM_ON· 545

TX_POW_HIGH· 545

TX_POW_LOW·· 545

TX_POW_NORMAL· 546

TYPE_ERR· 546

VOLT_HIGH· 546

VOLT_LOW·· 547

VOLT_NORMAL· 547

OSPF messages· 547

OSPF_DUP_RTRID_NBR· 548

OSPF_IP_CONFLICT_INTRA· 548

OSPF_LAST_NBR_DOWN· 549

OSPF_MEM_ALERT· 549

OSPF_NBR_CHG·· 550

OSPF_NBR_CHG_REASON· 551

OSPF_RT_LMT· 552

OSPF_RTRID_CHG·· 552

OSPF_RTRID_CONFLICT_INTER· 552

OSPF_RTRID_CONFLICT_INTRA· 553

OSPF_VLINKID_CHG·· 553

OSPFV3 messages· 553

OSPFV3_LAST_NBR_DOWN· 554

OSPFV3_MEM_ALERT· 554

OSPFV3_NBR_CHG·· 555

OSPFV3_RT_LMT· 555

PBB messages· 555

PBB_JOINAGG_WARNING·· 556

PBR messages· 556

PBR_HARDWARE_ERROR· 556

PCE messages· 556

PCE_PCEP_SESSION_CHG·· 557

PEX messages (IRF 3) 557

PEX_ASSOCIATEID_MISMATCHING·· 558

PEX_CONFIG_ERROR· 558

PEX_CONNECTION_ERROR· 559

PEX_FORBID_STACK· 559

PEX_LINK_BLOCK· 560

PEX_LINK_DOWN· 561

PEX_LINK_FORWARD· 561

PEX_REG_JOININ· 562

PEX_REG_LEAVE· 562

PEX_REG_REQUEST· 563

PEX_STACKCONNECTION_ERROR· 563

PEX messages (IRF 3.1) 564

PEX_AUTOCONFIG_BAGG_ASSIGNMEMBER· 564

PEX_AUTOCONFIG_BAGG_CREATE· 564

PEX_AUTOCONFIG_BAGG_NORESOURCE· 564

PEX_AUTOCONFIG_BAGG_REMOVEMEMBER· 565

PEX_AUTOCONFIG_CAPABILITY_ENABLE· 565

PEX_AUTOCONFIG_CASCADELIMIT· 566

PEX_AUTOCONFIG_CONNECTION_ERROR· 566

PEX_AUTOCONFIG_DIFFGROUPNUMBER· 566

PEX_AUTOCONFIG_DYNAMICBAGG_STP· 567

PEX_AUTOCONFIG_GROUP_CREATE· 567

PEX_AUTOCONFIG_NONUMBERRESOURCE· 567

PEX_AUTOCONFIG_NOT_CASCADEPORT· 568

PEX_AUTOCONFIG_NUMBER_ASSIGN· 568

PEX_LLDP_DISCOVER· 569

PEX_MEMBERID_EXCEED· 569

PEX_PECSP_OPEN_RCVD· 569

PEX_PECSP_OPEN_SEND· 570

PEX_PECSP_TIMEOUT· 570

PFILTER messages· 570

PFILTER_GLB_IPV4_DACT_NO_RES· 571

PFILTER_GLB_IPV4_DACT_UNK_ERR· 571

PFILTER_GLB_IPV6_DACT_NO_RES· 572

PFILTER_GLB_IPV6_DACT_UNK_ERR· 572

PFILTER_GLB_MAC_DACT_NO_RES· 573

PFILTER_GLB_MAC_DACT_UNK_ERR· 573

PFILTER_GLB_NO_RES· 574

PFILTER_GLB_NOT_SUPPORT· 574

PFILTER_GLB_ RES_CONFLICT· 575

PFILTER_GLB_UNK_ERR· 575

PFILTER_IF_IPV4_DACT_NO_RES· 576

PFILTER_IF_IPV4_DACT_UNK_ERR· 576

PFILTER_IF_IPV6_DACT_NO_RES· 577

PFILTER_IF_IPV6_DACT_UNK_ERR· 577

PFILTER_IF_MAC_DACT_NO_RES· 578

PFILTER_IF_MAC_DACT_UNK_ERR· 578

PFILTER_IF_NO_RES· 579

PFILTER_IF_NOT_SUPPORT· 579

PFILTER_IF_RES_CONFLICT· 580

PFILTER_IF_UNK_ERR· 580

PFILTER_IPV4_FLOW_INFO·· 581

PFILTER_IPV4_FLOW_STATIS· 581

PFILTER_IPV6_FLOW_INFO·· 582

PFILTER_IPV6_FLOW_STATIS· 582

PFILTER_IPV6_STATIS_INFO·· 583

PFILTER_MAC_FLOW_INFO·· 583

PFILTER_STATIS_INFO·· 584

PFILTER_VLAN_IPV4_DACT_NO_RES· 584

PFILTER_VLAN_IPV4_DACT_UNK_ERR· 585

PFILTER_VLAN_IPV6_DACT_NO_RES· 585

PFILTER_VLAN_IPV6_DACT_UNK_ERR· 586

PFILTER_VLAN_MAC_DACT_NO_RES· 586

PFILTER_VLAN_MAC_DACT_UNK_ERR· 587

PFILTER_VLAN_NO_RES· 587

PFILTER_VLAN_NOT_SUPPORT· 588

PFILTER_VLAN_RES_CONFLICT· 588

PFILTER_VLAN_UNK_ERR· 589

PIM messages· 589

PIM_NBR_DOWN· 589

PIM_NBR_UP· 590

PING messages· 590

PING_STATISTICS· 590

PING_VPN_STATISTICS· 591

PKG messages· 591

PKG_BOOTLOADER_FILE_FAILED· 591

PKG_BOOTLOADER_FILE_SUCCESS· 592

PKG_INSTALL_ACTIVATE_FAILED· 592

PKG_INSTALL_ACTIVATE_SUCCESS· 592

PKI messages· 592

GET_CERT_FROM_CA_SERVER_FAIL· 593

IMPORT_CERT_FAIL· 594

REQUEST_CERT_FAIL· 595

REQUEST_CERT_SUCCESS· 596

RETRIEVE_CRL_FAIL· 596

VALIDATE_CERT_FAIL· 597

PKT2CPU messages· 598

PKT2CPU_NO_RESOURCE· 599

PKTCPT· 599

PKTCPT_AP_OFFLINE· 599

PKTCPT_AREADY_EXIT· 600

PKTCPT_CONN_FAIL· 600

PKTCPT_INVALID_FILTER· 601

PKTCPT_LOGIN_DENIED· 601

PKTCPT_MEMORY_ALERT· 601

PKTCPT_OPEN_FAIL· 602

PKTCPT_OPERATION_TIMEOUT· 602

PKTCPT_SERVICE_FAIL· 603

PKTCPT_UNKNOWN_ERROR· 603

PKTCPT_UPLOAD_ERROR· 603

PKTCPT_WRITE_FAIL· 604

PoE messages· 604

POE_AI_CLEAR· 604

POE_AI_DETECTIONMODE_NONE· 605

POE_AI_DETECTIONMODE_SIMPLE· 605

POE_AI_DISCONNECT_AC· 605

POE_AI_DISCONNECT_DELAY· 606

POE_AI_FORCE_PoE· 606

POE_AI_HIGH_INRUSH· 606

POE_AI_LEGACY· 607

POE_AI_MAXPOWER· 607

POE_AI_RESTART· 607

Portal messages· 608

PORTAL_RULE_FAILED· 608

PORTSEC messages· 608

PORTSEC_ACL_FAILURE· 609

PORTSEC_CAR_FAILURE· 609

PORTSEC_CREATEAC_FAILURE· 610

PORTSEC_LEARNED_MACADDR· 610

PORTSEC_NTK_NOT_EFFECTIVE· 611

PORTSEC_PORTMODE_NOT_EFFECTIVE· 611

PORTSEC_PROFILE_FAILURE· 612

PORTSEC_URL_FAILURE· 612

PORTSEC_VIOLATION· 613

PORTSEC_VLANMACLIMIT· 613

PPP messages· 613

IPPOOL_ADDRESS_EXHAUSTED· 614

PPP_USER_LOGON_SUCCESS· 614

PPP_USER_LOGON_FAILED· 615

PPP_USER_LOGOFF· 615

PTS· 616

PTS_AK_AUTH_FAILED· 616

PTS_AK_INVALID· 617

PTS_AK_NO_CERT· 617

PTS_AK_NO_EXIST· 617

PTS_AK_NO_LOAD· 618

PTS_BTW_PCR_FAILED· 618

PTS_CHECK_RM_VERSION_FAILED· 618

PTS_CREATE_AGED_TIMER_FAILED· 619

PTS_CREATE_CHECK_TIMER_FAILED· 619

PTS_CREATE_CONTEXT_FAILED· 619

PTS_CREATE_EPOLL_FAILED· 620

PTS_CREATE_HASH_FAILED· 620

PTS_CREATE_SELFVERIFY_COUNTER_FAILED· 620

PTS_CREATE_SELFVERIFY_TIMER_FAILED· 621

PTS_CREATE_SOCKET_FAILED· 621

PTS_CREATE_TIMER_FAILED· 621

PTS_FILE_HASH_FAILED· 622

PTS_LOAD_KEY_FAILED· 622

PTS_PARSE_IML_FAILED· 622

PTS_PKG_PCR_FAILED· 623

PTS_READ_PCR_FAILED· 623

PTS_RM_FILE_FAILED· 623

PTS_RUNTIME_PCR_FAILED· 624

PTS_SELFVERIFY_FAILED· 624

PTS_SELFVERIFY_START_FAILED· 624

PTS_TEMPLATE_HASH_FAILED· 625

PWDCTL messages· 625

ADDBLACKLIST· 625

CHANGEPASSWORD· 626

FAILEDTOWRITEPWD· 626

FAILEDTOOPENFILE· 626

NOENOUGHSPACE· 627

UPDATETIME· 627

QOS messages· 627

MIRROR_SYNC_CFG_FAIL· 628

QOS_CAR_APPLYUSER_FAIL· 628

QOS_CBWFQ_REMOVED· 629

QOS_GTS_APPLYUSER_FAIL· 629

QOS_LR_APPLYIF_FAIL· 630

QOS_NOT_ENOUGH_BANDWIDTH· 630

QOS_NOT_ENOUGH_NNIBANDWIDTH· 631

QOS_POLICY_APPLYCOPP_CBFAIL· 631

QOS_POLICY_APPLYCOPP_FAIL· 632

QOS_POLICY_APPLYGLOBAL_CBFAIL· 632

QOS_POLICY_APPLYGLOBAL_FAIL· 633

QOS_POLICY_APPLYIF_CBFAIL· 633

QOS_POLICY_APPLYIF_FAIL· 634

QOS_POLICY_APPLYUSER_FAIL· 634

QOS_POLICY_APPLYVLAN_CBFAIL· 635

QOS_POLICY_APPLYVLAN_FAIL· 635

QOS_QMPROFILE_APPLYIF_FAIL· 636

QOS_QMPROFILE_APPLYUSER_FAIL· 636

QOS_QMPROFILE_MODIFYQUEUE_FAIL· 637

QOS_QUEUE_APPLYIF_FAIL· 637

QOS_UNI_RESTORE_FAIL· 638

WRED_TABLE_CFG_FAIL· 638

RADIUS messages· 638

RADIUS_AUTH_FAILURE· 639

RADIUS_AUTH_SUCCESS· 639

RADIUS_DELETE_HOST_FAIL· 639

RDDC messages· 639

RDDC_ACTIVENODE_CHANGE· 640

RESMON· 640

RESMON_MINOR· 640

RESMON_MINOR_RECOVERY· 641

RESMON_SEVERE· 641

RESMON_SEVERE_RECOVERY· 642

RESMON_USEDUP· 642

RESMON_USEDUP_RECOVERY· 643

RIP messages· 643

RIP_MEM_ALERT· 643

RIP_RT_LMT· 644

RIPNG messages· 644

RIPNG_MEM_ALERT· 644

RIPNG_RT_LMT· 644

RM messages· 644

RM_ACRT_REACH_LIMIT· 645

RM_ACRT_REACH_THRESVALUE· 645

RM_THRESHLD_VALUE_REACH· 645

RM_TOTAL_THRESHLD_VALUE_REACH· 646

RPR messages· 646

RPR_EXCEED_MAX_SEC_MAC· 646

RPR_EXCEED_MAX_SEC_MAC_OVER· 647

RPR_EXCEED_MAX_STATION· 647

RPR_EXCEED_MAX_STATION_OVER· 647

RPR_EXCEED_RESERVED_RATE· 648

RPR_EXCEED_RESERVED_RATE_OVER· 648

RPR_IP_DUPLICATE· 648

RPR_IP_DUPLICATE_OVER· 649

RPR_JUMBO_INCONSISTENT· 649

RPR_JUMBO_INCONSISTENT_OVER· 649

RPR_LAGGCONFIG_INCONSISTENT· 650

RPR_LAGGCONFIG_INCONSISTENT_OVER· 650

RPR_MISCABLING·· 650

RPR_MISCABLING_OVER· 651

RPR_PROTECTION_INCONSISTENT· 651

RPR_PROTECTION_INCONSISTENT_OVER· 651

RPR_SEC_MAC_DUPLICATE· 652

RPR_SEC_MAC_DUPLICATE_OVER· 652

RPR_TOPOLOGY_INCONSISTENT· 652

RPR_TOPOLOGY_INCONSISTENT_OVER· 653

RPR_TOPOLOGY_INSTABILITY· 653

RPR_TOPOLOGY_INSTABILITY_OVER· 653

RPR_TOPOLOGY_INVALID· 654

RPR_TOPOLOGY_INVALID_OVER· 654

RRPP messages· 654

RRPP_RING_FAIL· 654

RRPP_RING_RESTORE· 655

RTM messages· 655

RTM_TCL_NOT_EXIST· 655

RTM_TCL_MODIFY· 655

RTM_TCL_LOAD_FAILED· 656

SCMD messages· 656

PROCESS_ABNORMAL· 656

PROCESS_ACTIVEFAILED· 657

PROCESS_CORERECORD· 657

SCM_ABNORMAL_REBOOT· 658

SCM_ABNORMAL_REBOOTMDC· 658

SCM_ABORT_RESTORE· 659

SCM_INSMOD_ADDON_TOOLONG·· 659

SCM_KERNEL_INIT_TOOLONG·· 659

SCM_KILL_PROCESS· 660

SCM_PROCESS_STARTING_TOOLONG·· 661

SCM_PROCESS_STILL_STARTING·· 662

SCM_SKIP_PROCESS· 662

SCRLSP messages· 663

SCRLSP_LABEL_DUPLICATE· 663

SESSION messages· 663

SESSION_IPV4_FLOW·· 664

SESSION_IPV6_FLOW·· 665

SFLOW messages· 666

SFLOW_HARDWARE_ERROR· 666

SHELL messages· 666

SHELL_CMD· 666

SHELL_CMD_CONFIRM·· 667

SHELL_CMD_EXECUTEFAIL· 667

SHELL_CMD_INPUT· 667

SHELL_CMD_INPUT_TIMEOUT· 668

SHELL_CMD_INVALID_CHARACTER· 668

SHELL_CMD_MATCHFAIL· 668

SHELL_CMDDENY· 669

SHELL_CMDFAIL· 669

SHELL_COMMIT· 669

SHELL_COMMIT_DELAY· 670

SHELL_COMMIT_REDELAY· 670

SHELL_COMMIT_ROLLBACK· 670

SHELL_COMMIT_ROLLBACKDONE· 671

SHELL_COMMIT_WILLROLLBACK· 671

SHELL_CRITICAL_CMDFAIL· 671

SHELL_LOGIN· 672

SHELL_LOGOUT· 672

SLSP messages· 672

SLSP_LABEL_DUPLICATE· 673

SMLK messages· 673

SMLK_LINK_SWITCH· 673

SNMP messages· 673

SNMP_ACL_RESTRICTION· 674

SNMP_AUTHENTICATION_FAILURE· 674

SNMP_GET· 674

SNMP_INFORM_LOST· 675

SNMP_NOTIFY· 676

SNMP_SET· 677

SNMP_USM_NOTINTIMEWINDOW·· 677

SSHC messages· 677

SSHC_ALGORITHM_MISMATCH· 678

SSHC_AUTH_PASSWORD_FAIL· 678

SSHC_AUTH_PUBLICKEY_FAIL· 678

SSHC_CERT_VERIFY_FAIL· 679

SSHC_CONNECT_FAIL· 680

SSHC_DECRYPT_FAIL· 680

SSHC_DISCONNECT· 681

SSHC_ENCRYPT_FAIL· 681

SSHC_HOST_NAME_ERROR· 681

SSHC_KEY_EXCHANGE_FAIL· 682

SSHC_MAC_ERROR· 682

SSHC_PUBLICKEY_NOT_EXIST· 682

SSHC_VERSION_MISMATCH· 683

SSHS messages· 683

SSHS_ACL_DENY· 683

SSHS_ALGORITHM_MISMATCH· 683

SSHS_AUTH_EXCEED_RETRY_TIMES· 684

SSHS_AUTH_FAIL· 684

SSHS_AUTH_KBDINT_FAIL· 684

SSHS_AUTH_PWD_FAIL· 685

SSHS_AUTH_TIMEOUT· 685

SSHS_AUTH_SUCCESS· 685

SSHS_AUTHOR_FAIL· 686

SSHS_CERT_VERIFY_FAIL· 687

SSHS_CONNECT· 688

SSHS_DECRYPT_FAIL· 688

SSHS_DISCONNECT· 689

SSHS_ENCRYPT_FAIL· 689

SSHS_LOG·· 690

SSHS_MAC_ERROR· 690

SSHS_REACH_SESSION_LIMIT· 691

SSHS_REACH_USER_LIMIT· 691

SSHS_SCP_OPER· 691

SSHS_SFTP_OPER· 692

SSHS_SRV_UNAVAILABLE· 692

SSHS_VERSION_MISMATCH· 693

STAMGR messages· 693

STAMGR_ADD_FAILVLAN· 693

STAMGR_ADDBAC_INFO·· 693

STAMGR_ADDSTA_INFO·· 694

STAMGR_AUTHORACL_FAILURE· 694

STAMGR_AUTHORUSERPROFILE_FAILURE· 694

STAMGR_CLIENT_OFFLINE· 695

STAMGR_CLIENT_ONLINE· 695

STAMGR_DELBAC_INFO·· 695

STAMGR_DELSTA_INFO·· 696

STAMGR_DOT1X_LOGIN_FAILURE· 696

STAMGR_DOT1X_LOGIN_SUCC· 697

STAMGR_DOT1X_LOGOFF· 697

STAMGR_MACA_LOGIN_FAILURE· 698

STAMGR_MACA_LOGIN_SUCC· 698

STAMGR_MACA_LOGOFF· 699

STAMGR_STAIPCHANGE_INFO·· 699

STAMGR_TRIGGER_IP· 700

STM messages· 700

STM_AUTO_UPDATE_FAILED· 701

STM_AUTO_UPDATE_FINISHED· 702

STM_AUTO_UPDATING·· 702

STM_LINK_DOWN· 703

STM_LINK_TIMEOUT· 703

STM_LINK_UP· 703

STM_MERGE· 704

STM_MERGE_NEED_REBOOT· 704

STM_MERGE_NOT_NEED_REBOOT· 704

STM_SAMEMAC· 705

STM_SOMER_CHECK· 705

STP messages· 705

STP_BPDU_PROTECTION· 706

STP_BPDU_RECEIVE_EXPIRY· 706

STP_CONSISTENCY_CHECK· 706

STP_CONSISTENCY_RESTORATION· 707

STP_DETECTED_TC· 707

STP_DISABLE· 707

STP_DISCARDING·· 708

STP_DISPUTE· 708

STP_ENABLE· 708

STP_FORWARDING·· 709

STP_LOOP_PROTECTION· 709

STP_LOOPBACK_PROTECTION· 709

STP_NOT_ROOT· 710

STP_NOTIFIED_TC· 710

STP_PORT_TYPE_INCONSISTENCY· 710

STP_PVID_INCONSISTENCY· 711

STP_PVST_BPDU_PROTECTION· 711

STP_ROOT_PROTECTION· 711

SYSLOG messages· 712

SYSLOG_LOGBUFFER_FAILURE· 712

SYSLOG_LOGFILE_FULL· 712

SYSLOG_NO_SPACE· 712

SYSLOG_RESTART· 713

SYSLOG_RTM_EVENT_BUFFER_FULL· 713

TACACS messages· 713

TACACS_AUTH_FAILURE· 714

TACACS_AUTH_SUCCESS· 714

TACACS_DELETE_HOST_FAIL· 714

TCSM·· 714

TCSM_CERT_BROKEN· 715

TCSM_KEY_BROKEN· 715

TCSM_KEY_HIERARCHY_BROKEN· 715

TCSM_TSS_SVC_DOWN· 716

TCSM_TSS_SVC_UP· 716

TELNETD messages· 716

TELNETD_ACL_DENY· 716

TELNETD_REACH_SESSION_LIMIT· 717

TRILL messages· 717

TRILL_DUP_SYSTEMID· 717

TRILL_INTF_CAPABILITY· 718

TRILL_LICENSE_EXPIRED· 718

TRILL_LICENSE_EXPIRED_TIME· 718

TRILL_LICENSE_UNAVAILABLE· 719

TRILL_MEM_ALERT· 719

TRILL_NBR_CHG·· 719

VCF messages· 720

VCF_AGGR_CREAT· 720

VCF_AGGR_DELETE· 720

VCF_AGGR_FAILED· 721

VCF_AUTO_ANALYZE_USERDEF· 721

VCF_AUTO_NO_USERDEF· 721

VCF_AUTO_START· 722

VCF_AUTO_STATIC_CMD· 722

VCF_BGP· 723

VCF_DOWN_LINK· 724

VCF_DRIVER_INIT· 724

VCF_GET_IMAGE· 725

VCF_GET_TEMPLATE· 725

VCF_INSTALL_IMAGE· 726

VCF_IRF_FINISH· 726

VCF_IRF_FOUND· 727

VCF_IRF_START· 727

VCF_LOOPBACK_START· 728

VCF_LOOPBACK_START_FAILED· 728

VCF_LOOPBACK_ALLOC· 729

VCF_LOOPBACK_NO_FREE_IP· 729

VCF_LOOPBACK_RECLAIM·· 730

VCF_REBOOT· 730

VCF_SKIP_INSTALL· 731

VCF_STATIC_CMD_ERROR· 731

VCF_UP_LINK· 731

VCF_WHITE_LIST_CHECK· 732

VLAN messages· 732

VLAN_CREATEFAIL· 732

VLAN_FAILED· 732

VLAN_QINQETHTYPE_FAILED· 733

VLAN_VLANMAPPING_FAILED· 733

VLAN_VLANTRANSPARENT_FAILED· 733

VRRP messages· 734

VRRP_STATUS_CHANGE· 734

VRRP_VF_STATUS_CHANGE· 735

VRRP_VMAC_INEFFECTIVE· 735

VSRP messages· 735

VSRP_BIND_FAILED· 736

VXLAN messages· 736

VXLAN_LICENSE_UNAVAILABLE· 736

WEB messages· 736

LOGIN· 737

LOGIN_FAILED· 737

LOGOUT· 737

WIPS messages· 737

APFLOOD· 738

AP_CHANNEL_CHANGE· 738

ASSOCIATEOVERFLOW·· 738

HONEYPOT· 739

HTGREENMODE· 739

MAN_IN_MIDDLE· 739

WIPS_DOS· 740

WIPS_FLOOD· 740

WIPS_MALF· 741

WIPS_SPOOF· 741

WIPS_WEAKIV· 742

WIRELESSBRIDGE· 742

 


Introduction

This document includes the following system messages:

·     Messages specific to Release 66xx of the switch.

·     Messages for the Comware 7 software platform version based on which Release 66xx was produced. Some platform system messages might not be available on the switch.

This document is intended only for managing S6805, S6850, S9850 or S9820 switches. Do not use this document for any other device models.

This document assumes that the readers are familiar with data communications technologies and H3C networking products.

System log message format

By default, the system log messages use one of the following formats depending on the output destination:

·     Log host:

<PRI>TIMESTAMP Sysname %%vendorMODULE/severity/MNEMONIC: location; CONTENT

·     Destinations except for the log host:

Prefix TIMESTAMP Sysname MODULE/severity/MNEMONIC: CONTENT

 

 

NOTE:

Log message examples in this document use the format for destinations except the log host. They do not contain elements available only for the log host, including the location element.

 

Table 1 System log message elements

Element

Description

<PRI>

Priority identifier. This element is contained only in messages sent to the log host.

It is calculated by using the following formula:

Priority identifier=facilityx8+severity

Where:

·     Facility is specified by using the info-center loghost command. A log host uses this parameter to identify log sources and filter log messages.

·     Severity represents the importance of the message. For more information about severity levels, see 错误!未找到引用源。.

Prefix

Message type identifier. This element is contained in the system log messages sent to non-log-host destinations.

The element uses the following symbols to indicate message severity:

·     Percentage sign (%)—Informational and higher levels.

·     Asterisk (*)—Debug level.

TIMESTAMP

Date and time when the event occurred.

The following are commands for configuring the timestamp format:

·     Log host—Use the info-center timestamp loghost command.

·     Non-log-host destinations—Use the info-center timestamp command.

Sysname

Name or IP address of the device that generated the message.

%%vendor

Manufacturer flag. This element is %%10 for H3C.

This element is only available in messages sent to the log host.

MODULE

Name of the module that produced the message.

severity

Severity level of the message. (For more information about severity levels, see 错误!未找到引用源。.)

MNEMONIC

Text string that uniquely identifies the system message. The maximum length is 32 characters.

location

Optional. This element identifies where the message occurred. This element is contained only in messages sent to the log host.

This element presents location information for the message in the following format:

-attribute1=x-attribute2=y…-attributeN=z

The following are examples of location attributes:

·     -MDC=XX, which represents the MDC on which the message occurred.

·     -DevIp=XXX.XXX.XXX.XXX, which represents the source IP of the message.

·     -Slot=XX, which represents the slot on which the message occurred.

·     -Chassis=XX-Slot=XX, which represents the chassis and slot on which the message occurred.

This element is separated from the message description by using a semicolon (;).

CONTENT

Text string that contains detailed information about the event or error.

For variable fields in this element, this document uses the representations in 错误!未找到引用源。.

 

System log messages are classified into eight severity levels from 0 to 7. The lower the number, the higher the severity, as shown in 错误!未找到引用源。.

Table 2 System log message severity levels

Level

Severity

Description

0

Emergency

The system is unusable. For example, the system authorization has expired.

1

Alert

Action must be taken immediately. For example, traffic on an interface exceeds the upper limit.

2

Critical

Critical condition. For example, the device temperature exceeds the upper limit, the power module fails, or the fan tray fails.

3

Error

Error condition. For example, the link state changes or a storage card is unplugged.

4

Warning

Warning condition. For example, an interface is disconnected, or the memory resources are used up.

5

Notification

Normal but significant condition. For example, a terminal logs in to the device, or the device reboots.

6

Informational

Informational message. For example, a command or a ping operation is executed.

7

Debug

Debugging message.

 

For variable fields in the message text, this document uses the representations in 错误!未找到引用源。. The values are case insensitive, even though the representations are uppercase letters.

Table 3 Variable field representations

Representation

Information type

INT16

Signed 16-bit decimal number.

UINT16

Unsigned 16-bit decimal number.

INT32

Signed 32-bit decimal number.

UINT32

Unsigned 32-bit decimal number.

INT64

Signed 64-bit decimal number.

UINT64

Unsigned 64-bit decimal number.

DOUBLE

Two dot-separated signed 32-bit decimal numbers. The format is [INTEGER].[INTEGER].

HEX

Hexadecimal number.

CHAR

Single character.

STRING

Character string.

IPADDR

IP address.

MAC

MAC address.

DATE

Date.

TIME

Time.

 

Managing and obtaining system log messages

You can manage system log messages by using the information center.

By default, the information center is enabled. Log messages can be output to the console, monitor terminal, log buffer, log host, and log file.

To filter log messages, use the info-center source command to specify log output rules. A log output rule specifies the source modules and the lowest severity level of log messages that can be output to a destination. A log message is output if its severity level is higher than or equal to the specified level. For example, if you specify a severity level of 6 (informational), log messages that have a severity level from 0 to 6 are output.

For more information about using the information center, see the network management and monitoring configuration guide for the product.

Obtaining log messages from the console terminal

Access the device through the console port. Real-time log messages are displayed on the console terminal.

Obtaining log messages from a monitor terminal

Monitor terminals refer to terminals that access the device through the VTY, lines (for example, Telnet). To obtain log messages from a monitor terminal, use the following guidelines:

·     To display log messages on the monitor terminal, you must configure the terminal monitor command.

·     For monitor terminals, the lowest level of log messages that can be displayed is determined by both the terminal logging level and info-center source commands.

 

 

NOTE:

Settings for the terminal monitor and terminal logging level commands take effect only on the current login session. The default settings for the commands restore at a relogin.

 

Obtaining log messages from the log buffer

Use the display logbuffer command to display history log messages in the log buffer.

Obtaining log messages from the log file

By default, the log file feature automatically saves logs from the log file buffer to the log file every 24 hours. You can use the info-center logfile frequency command to change the automatic saving internal.

To manually save logs to the log file, use the logfile save command. The log file buffer is cleared each time a save operation is performed.

By default, you can obtain the log file from the flash:/logfile path.

To view the contents of the log file on the device, use the more command.

Obtaining log messages from a log host

Use the info-center loghost command to specify the service port number and IP address of a log host. To specify multiple log hosts, repeat the command.

For a successful log message transmission, make sure the specified port number is the same as the port number used on the log host. The default service port number is 514.

Software module list

错误!未找到引用源。 lists all software modules that might produce system log messages. This document uses "OPENSRC" to represent all open source modules.

Table 4 Software module list

Module name representation

Module name expansion

AAA

Authentication, Authorization and Accounting

ACL

Access Control List

ANCP

Access Node Control Protocol

APMGR

Access Point Management

ARP

Address Resolution Protocol

ATK

Attack Detection and Prevention

ATM

Asynchronous Transfer Mode

BFD

Bidirectional Forwarding Detection

BGP

Border Gateway Protocol

BLS

Blacklist

CFD

Connectivity Fault Detection

CFGMAN

Configuration Management

CONNLMT

Connection Limit

DEV

Device Management

DHCP

Dynamic Host Configuration Protocol

DHCPR

IPv4 DHCP Relay

DHCPS

DHCP Server

DHCPS6

DHCPv6 Server

DHCPSP4

DHCP Snooping

DHCPSP6

DHCPv6 Snooping

DIAG

Diagnosis

DLDP

Device Link Detection Protocol

DOT1X

802.1X

DRNI

Distributed Resilient Network Interconnect

DRVPLAT

Driver platform

EDEV

Extended-Device Management

ERPS

Ethernet Ring Protection Switching

ETH

Ethernet

ETHOAM

Ethernet Operation, Administration and Maintenance

EVB

Edge Virtual Bridging

EVIISIS

Ethernet Virtual Interconnect Intermediate System-to-Intermediate System

FCOE

Fibre Channel Over Ethernet

FCLINK

Fibre Channel Link

FCZONE

Fibre Channel Zone

FIB

Forwarding Information Base

FILTER

Filter

FIPSNG

FIP Snooping

FS

File System

FTP

File Transfer Protocol

gRPC

Google Remote Procedure Call

HA

High Availability

HQOS

Hierarchical QoS

HTTPD

Hypertext Transfer Protocol Daemon

IFNET

Interface Net Management

IKE

Internet Key Exchange

IMA

Integrity Measurements Architecture

IP6ADDR

IPv6 Addressing

IP6FW

IPv6 Forwarding

IPADDR

IP Addressing

IPFW

IP Forwarding

IPSEC

IP Security

IPSG

IP Source Guard

IRDP

ICMP Router Discovery Protocol

IRF

Intelligent Resilient Framework

ISIS

Intermediate System-to-Intermediate System

ISSU

In-Service Software Upgrade

L2PT

Layer 2 Protocol Tunneling

L2TPV2

Layer 2 Tunneling Protocol Version 2

L2VPN

Layer 2 VPN

LAGG

Link Aggregation

LDP

Label Distribution Protocol

LLDP

Link Layer Discovery Protocol

LOAD

Load Management

LOGIN

Login

LPDT

Loopback Detection

LS

Local Server

LSPV

LSP Verification

MAC

Media Access Control

MACA

MAC Authentication

MACSEC

MAC Security

MBFD

MPLS BFD

MBUF

Memory buffer

MDC

Multitenant Device Context

MFIB

Multicast Forwarding Information Base

MGROUP

Mirroring group

MPLS

Multiprotocol Label Switching

MTLK

Monitor Link

NAT

Network Address Translation

NETCONF

Network Configuration Protocol

ND

Neighbor Discovery

NQA

Network Quality Analyzer

NTP

Network Time Protocol

OAP

Open Application Platform

OPENSRC (FreeRADIUS)

Open Source

OBJP

Object Policy

OFP

OpenFlow Protocol

OPTMOD

Optical Module

OSPF

Open Shortest Path First

OSPFV3

Open Shortest Path First Version 3

PFILTER

Packet Filter

PBB

Provider Backbone Bridge

PBR

Policy-Based Routing

PCE

Path Computation Element

PEX

Port Extender

PIM

Protocol Independent Multicast

PING

Packet Internet Groper

PKG

Package

PKI

Public Key Infrastructure

PKT2CPU

Packet to CPU

PKTCPT

Packet Capture

PoE

Power over Ethernet

PORTAL

Portal

PORTSEC

Port Security

PPP

Point to Point Protocol

PTS

Platform Trust Services

PWDCTL

Password Control

QOS

Quality of Service

RADIUS

Remote Authentication Dial In User Service

RESMON

Resource Monitor

RDDC

Redundancy

RIP

Routing Information Protocol

RIPNG

Routing Information Protocol Next Generation

RM

Routing Management

RPR

Resilient Packet Ring

RRPP

Rapid Ring Protection Protocol

RTM

Real-Time Event Manager

SCMD

Service Control Manager Daemon

SCRLSP

Static CRLSP

SESSION

Session

SFLOW

Sampler Flow

SHELL

Shell

SLSP

Static LSP

SMLK

Smart Link

SNMP

Simple Network Management Protocol

SSHC

Secure Shell Client

SSHS

Secure Shell Server

STAMGR

Station Management

STM

Stack Topology Management

STP

Spanning Tree Protocol

SYSEVENT

System Event

SYSLOG

System Log

TACACS

Terminal Access Controller Access Control System

TCSM

Trusted Computing Services Management

TELNETD

Telnet Daemon

TRILL

Transparent Interconnect of Lots of Links

VCF

Vertical Converged Framework

VLAN

Virtual Local Area Network

VRRP

Virtual Router Redundancy Protocol

VSRP

Virtual Service Redundancy Protocol

VXLAN

Virtual eXtensible LAN

WEB

Web

WIPS

Wireless Intrusion Prevention System

 

Using this document

This document categorizes system log messages by software module. The modules are ordered alphabetically. Except for OPENSRC, the system log messages for each module are listed in alphabetic order of their mnemonic names. The OPENSRC messages are unordered because they use the same mnemonic name (SYSLOG). For each OPENSRC message, the section title uses a short description instead of the mnemonic name.

This document explains messages in tables. 错误!未找到引用源。 describes information provided in these tables.

Table 5 Message explanation table contents

Item

Content

Example

Message text

Presents the message description.

ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

Briefly describes the variable fields in the order that they appear in the message text.

The variable fields are numbered in the "$Number" form to help you identify their location in the message text.

$1: ACL number.

$2: ID and content of an ACL rule.

$3: Number of packets that matched the rule.

Severity level

Provides the severity level of the message.

6

Example

Provides a real message example. The examples do not include the "<PRI>TIMESTAMP Sysname %%vendor" part or the "Prefix TIMESTAMP Sysname" part, because information in this part varies with system settings.

ACL/6/ACL_STATIS_INFO: ACL 2000 rule 0 permit source 1.1.1.1 0 logging 10000 packet(s).

Explanation

Explains the message, including the event or error cause.

Number of packets that matched an ACL rule. This message is sent when the packet counter changes.

Recommended action

Provides recommended actions. For informational messages, no action is required.

No action is required.

 

AAA messages

This section contains AAA messages.

AAA_FAILURE

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA failed.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

5

Example

AAA/5/AAA_FAILURE: -AAAType=AUTHOR-AAADomain=domain1-Service=login-UserName=cwf@system; AAA failed.

Explanation

An AAA request was rejected.

The following are the common reasons:

·     No response was received from the server.

·     The username or password was incorrect.

·     The service type that the user applied for was incorrect.

Recommended action

1.     Verify that the device is correctly connected to the server.

2.     Enter the correct username and password.

3.     Verify that the server settings are the same as the settings on the device.

4.     If the problem persists, contact H3C Support.

 

AAA_LAUNCH

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA launched.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

6

Example

AAA/6/AAA_LAUNCH: -AAAType=AUTHEN-AAADomain=domain1-Service=login-UserName=cwf@system; AAA launched.

Explanation

An AAA request was received.

Recommended action

No action is required.

 

AAA_SUCCESS

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA succeeded.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

6

Example

AAA/6/AAA_SUCCESS: -AAAType=AUTHOR-AAADomain=domain1-Service=login-UserName=cwf@system; AAA succeeded.

Explanation

An AAA request was accepted.

Recommended action

No action is required.

 

ACL messages

This section contains ACL messages.

ACL_ACCELERATE_NO_RES

Message text

Failed to accelerate [STRING] ACL [UINT32]. The resources are insufficient.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NO_RES: Failed to accelerate IPv6 ACL 2001. The resources are insufficient.

Explanation

Hardware resources were insufficient for accelerating an ACL.

Recommended action

Delete some rules or disabled ACL acceleration for other ACLs to release hardware resources.

 

ACL_ACCELERATE_NONCONTIGUOUSMASK

Message text

Failed to accelerate ACL [UINT32]. ACL acceleration supports only contiguous wildcard masks.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NONCONTIGUOUSMASK: Failed to accelerate ACL 2001. ACL acceleration supports only contiguous wildcard masks.

Explanation

ACL acceleration failed because rules containing noncontiguous wildcard masks exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_NOT_SUPPORT

Message text

Failed to accelerate [STRING] ACL [UINT32]. The operation is not supported.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORT: Failed to accelerate IPv6 ACL 2001. The operation is not supported.

Explanation

ACL acceleration failed because the system does not support ACL acceleration.

Recommended action

No action is required.

 

ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP

Message text

Failed to accelerate IPv6 ACL [UINT32]. ACL acceleration does not support the rules that contain the hop-by-hop keywords.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP: Failed to accelerate IPv6 ACL 2001. ACL acceleration does not support the rules that contain the hop-by-hop keywords.

Explanation

ACL acceleration failed for the IPv6 ACL because rules containing the hop-by-hop keyword exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG

Message text

Failed to accelerate IPv6 ACL [UINT32]. ACL acceleration does not support specifying multiple TCP flags in one rule.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG: Failed to accelerate IPv6 ACL 2001. ACL acceleration does not support specifying multiple TCP flags in one rule.

Explanation

ACL acceleration failed for the IPv6 ACL because rules containing multiple TCP flags exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_UNK_ERR

Message text

Failed to accelerate [STRING] ACL [UINT32].

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_UNK_ERR: Failed to accelerate IPv6 ACL 2001.

Explanation

ACL acceleration failed because of an unknown error.

Recommended action

No action is required.

 

ACL_IPV6_STATIS_INFO

Message text

IPv6 ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

$1: ACL number.

$2: ID and content of an IPv6 ACL rule.

$3: Number of packets that matched the rule.

Severity level

6

Example

ACL/6/ACL_IPV6_STATIS_INFO: IPv6 ACL 2000 rule 0 permit source 1:1::/64 logging 1000 packet(s).

Explanation

The number of packets matching the IPv6 ACL rule changed.

Recommended action

No action is required.

 

ACL_NO_MEM

Message text

Failed to configure [STRING] ACL [UINT] due to lack of memory.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

3

Example

ACL/3/ACL_NO_MEM: Failed to configure ACL 2001 due to lack of memory.

Explanation

Configuring the ACL failed because memory is insufficient.

Recommended action

Use the display memory-threshold command to check the memory usage.

 

ACL_STATIS_INFO

Message text

ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

$1: ACL number.

$2: ID and content of an IPv4 ACL rule.

$3: Number of packets that matched the rule.

Severity level

6

Example

ACL/6/ACL_STATIS_INFO: ACL 2000 rule 0 permit source 1.1.1.1 0 logging 10000 packet(s).

Explanation

The number of packets matching the IPv4 ACL rule changed.

Recommended action

No action is required.

 

ANCP messages

This section contains ANCP messages.

ANCP_INVALID_PACKET

Message text

-NeighborName=[STRING]-State=[STRING]-MessageType=[STRING]; The [STRING] value [STRING] is wrong, and the value [STRING] is expected.

Variable fields

$1: ANCP neighbor name.

$2: Neighbor state.

$3: Message type.

$4: Field.

$5: Wrong value of the field.

$6: Expected value of the field.

Severity level

6

Example

ANCP/6/ANCP_INVALID_PACKET: -NeighborName=Dslam-State=SYNSENT-MessageType=SYNACK; The Sender Instance value 0 is wrong, and the value 1 is expected.

Explanation

The system received an adjacency message that had a field with a wrong value.

Recommended action

No action is required.

 

APMGR messages

This section contains access point management messages.

APMGR_AC_MEM_ALERT

Message text

The memory utilization has reached the threshold.

Variable fields

N/A

Severity level

4

Example

APMGR/4/APMGR_AC_MEM_ALERT: The memory utilization has reached the threshold.

Explanation

The AP failed to come online because the memory utilization exceeded the limit.

Recommended action

Stop creating manual APs and prevent APs from coming online.

 

APMGR_ADD_AP_FAIL

Message text

AP [STRING] failed to come online using serial ID [STRING]: MAC address [STRING] is being used by AP [STRING].

Variable fields

$1: AP name.

$2: Serial ID.

$3: MAC address.

$4: AP name.

Severity level

4

Example

APMGR/4/ APMGR_ADD_AP_FAIL: AP ap1 failed to come online using serial ID 01247ef96: MAC address 0023-7961-5201 is being used by AP ap2.

Explanation

The AP failed to come online because a manual AP that has the same MAC address already exists on the AC.

Recommended action

Delete either the manual AP that has the MAC address or the serial ID.

 

APMGR_ADDBAC_INFO

Message text

Add BAS AC [STRING].

Variable fields

$1: MAC address of the BAS AC.

Severity level

6

Example

APMGR/6/APMGR_ADDBAC_INFO: Add BAS AC 3ce5-a616-28cd.

Explanation

The BAS AC was connected to the master AC.

Recommended action

No action is required.

 

APMGR_AP_OFFLINE

Message text

AP [STRING] went offline. State changed to Idle.

Variable fields

$1: AP name.

Severity level

6

Example

APMGR/6/APMGR_AP_OFFLINE: AP ap1 went offline. State changed to Idle.

Explanation

The AP went offline. The state of the AP changed to Idle.

Recommended action

If the AP went offline abnormally, check the debugging information to locate the issue and resolve it.

 

APMGR_AP_ONLINE

Message text

AP [STRING] went online. State changed to Run.

Variable fields

$1: AP name.

Severity level

6

Example

APMGR/6/APMGR_AP_ONLINE: AP ap1 went online. State changed to Run.

Explanation

The AP came online. The state of the AP changed to Run.

Recommended action

No action is required.

 

APMGR_CWC_IMG_DOWNLOAD_COMPLETE

Message text

System software image file [STRING] downloading through the CAPWAP tunnel to AC [STRING] completed.

Variable fields

$1: Image file name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_DOWNLOAD_COMPLETE: System software image file 5800.ipe downloading through the CAPWAP tunnel to AC 192.168.10.1 completed.

Explanation

The AP downloaded the image file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWC_IMG_DOWNLOAD_START

Message text

Started to download the system software image file [STRING] through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: Image file name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_DOWNLOAD_START: Started to download the system software image file 5800.ipe through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP started to download the image file from the AC.

Recommended action

Make sure the AP is correctly connected to the AC.

 

APMGR_CWC_IMG_NO_ENOUGH_SPACE

Message text

Insufficient flash memory space for downloading system software image file [STRING].

Variable fields

$1: Image file name.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_NO_ENOUGH_SPACE: Insufficient flash memory space for downloading system software image file 5800.ipe.

Explanation

The AP failed to download the image file from the AC because of insufficient flash memory.

Recommended action

Delete files not in use from the AP.

 

APMGR_CWC_LOCAL_AC_DOWN

Message text

CAPWAP tunnel to Central AC [STRING] went down. Reason: [STRING].

Variable fields

$1: IP address of the central AC.

$2: Reason:

·     Added local AC IP address.

·     Deleted local AC IP address.

·     Local AC interface used for CAPWAP tunnel went down.

·     Local AC config changed.

·     N/A

Severity level

4

Example

APMGR/4/APMGR_CWC_LOCAL_AC_DOWN: CAPWAP tunnel to Central AC 2.2.2.1 went down. Reason: Added local AC IP address.

Explanation

The CAPWAP tunnel between the central AC and the local AC was terminated for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the central AC and the local AC.

2.     Verify that the central AC is correctly configured.

3.     Verify that the local AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWC_LOCAL_AC_UP

Message text

CAPWAP tunnel to Central AC [STRING] went up.

Variable fields

$1: IP address of the central AC.

Severity level

6

Example

APMGR/6/APMGR_CWC_LOCAL_AC_UP: CAPWAP tunnel to Central AC 2.2.2.1 went up.

Explanation

The central AC has established a CAPWAP tunnel with the local AC.

Recommended action

No action is required.

 

APMGR_CWC_REBOOT

Message text

AP in state [STRING] is rebooting. Reason: [STRING]

Variable fields

$1: AP state.

$2: Reason:

·     AP was reset.

·     Image was downloaded successfully.

·     AP stayed in idle state for a long time.

Severity level

6

Example

APMGR/6/APMGR_CWC_REBOOT: AP in State Run is rebooting. Reason: AP was reset.

Explanation

The AP rebooted for a specific reason.

Recommended action

No action is required.

 

APMGR_CWC_RUN_DOWNLOAD_COMPLETE

Message text

File [STRING] successfully downloaded through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: File name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_DOWNLOAD_COMPLETE: File ac.cfg successfully downloaded through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP downloaded the file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWC_RUN_DOWNLOAD_START

Message text

Started to download the file [STRING] through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: File name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_DOWNLOAD_START: Started to download the file ac.cfg through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP started to download the file from the AC.

Recommended action

Make sure the AP is correctly connected to the AC.

 

APMGR_CWC_RUN_NO_ENOUGH_SPACE

Message text

Insufficient flash memory space for downloading file [STRING].

Variable fields

$1: File name.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_NO_ENOUGH_SPACE: Insufficient flash memory space for downloading file ac.cfg.

Explanation

The AP failed to download the file from the AC because of insufficient flash memory.

Recommended action

Delete files not in use from the AP.

 

APMGR_CWC_TUNNEL_DOWN

Message text

CAPWAP tunnel to AC [STRING] went down. Reason: [STRING].

Variable fields

$1: AC IP address.

$2: Reason:

·     Added AP IP address.

·     Deleted AP IP address.

·     AP interface used for CAPWAP tunnel went down.

·     AP config changed.

·     AP was reset.

·     Number of echo retransmission attempts exceeded the limit.

·     Full retransmission queue.

·     Data channel timer expired.

·     Backup AC IP address changed.

·     Backup tunnel changed to master tunnel.

·     Failed to change backup tunnel to master tunnel.

·     Backup method changed.

·     N/A.

Severity level

6

Example

APMGR/6/APMGR_CWC_TUNNEL_DOWN: CAPWAP tunnel to AC 192.168.10.1 went down. Reason: AP was reset.

Explanation

The CAPWAP tunnel between the AP and the AC was terminated for a specific reason.

Recommended action

Examine the network connection between the AP and the AC.

 

APMGR_CWC_TUNNEL_UP

Message text

[STRING] CAPWAP tunnel to AC [STRING] went up.

Variable fields

$1: Tunnel type:

·     Master.

·     Backup.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_TUNNEL_UP: Master CAPWAP tunnel to AC 192.168.10.1 went up.

Explanation

The AP was connected to the AC successfully and entered Run state.

Recommended action

No action is required.

 

APMGR_CWS_IMG_DOWNLOAD_COMPLETE

Message text

System software image file [STRING] downloading through the CAPWAP tunnel for AP [STRING] completed.

Variable fields

$1: Image file name.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_ CWS_IMG_DOWNLOAD_COMPLETE: System software image file 5800.ipe downloading through the CAPWAP tunnel for AP ap2 completed.

Explanation

The AP downloaded the image file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWS_IMG_DOWNLOAD_START

Message text

AP [STRING] started to download the system software image file [STRING].

Variable fields

$1: AP name.

$2: Image file name.

Severity level

6

Example

APMGR/6/APMGR_CWS_IMG_DOWNLOAD_START: AP ap1 started to download the system software image file 5800.ipe.

Explanation

The AP started to download the image file from the AC.

Recommended action

No action is required.

 

APMGR_CWS_LOCAL_AC_DOWN

Message text

CAPWAP tunnel to local AC [STRING] went down. Reason: [STRING].

Variable fields

$1: IP address of the local AC.

$2: Reason:

·     Neighbor dead timer expired.

·     Local AC was deleted.

·     Serial number changed.

·     Processed join request in Run state.

·     Failed to retransmit message.

·     N/A

Severity level

4

Example

APMGR/4/APMGR_CWS_LOCAL_AC_DOWN: CAPWAP tunnel to local AC 1.1.1.1 went down. Reason: Serial number changed.

Explanation

The CAPWAP tunnel between the central AC and the local AC was terminated for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the central AC and the local AC.

2.     Verify that the central AC is correctly configured.

3.     Verify that the local AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWS_LOCAL_AC_UP

Message text

CAPWAP tunnel to local AC [STRING] went up.

Variable fields

$1: IP address of the local AC.

Severity level

6

Example

APMGR/6/APMGR_CWS_LOCAL_AC_UP: CAPWAP tunnel to local AC 1.1.1.1 went up.

Explanation

The central AC has established a CAPWAP tunnel with the local AC.

Recommended action

No action is required.

 

APMGR_CWS_RUN_DOWNLOAD_COMPLETE

Message text

File [STRING] successfully downloaded through the CAPWAP tunnel for AP [STRING].

Variable fields

$1: File name.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_CWS_RUN_DOWNLOAD_COMPLETE: File ac.cfg successfully downloaded through the CAPWAP tunnel for AP ap2.

Explanation

The AP downloaded the file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWS_RUN_DOWNLOAD_START

Message text

AP [STRING] started to download the file [STRING].

Variable fields

$1: AP name.

$2: File name.

Severity level

6

Example

APMGR/6/APMGR_CWS_RUN_DOWNLOAD_START: AP ap1 started to download the file ac.cfg.

Explanation

The AP started to download the file from the AC.

Recommended action

No action is required.

 

APMGR_CWS_TUNNEL_DOWN

Message text

CAPWAP tunnel to AP [STRING] went down. Reason: [STRING].

Variable fields

$1: AP name.

$2: Reason:

·     Neighbor dead timer expired.

·     AP was reset.

·     AP was deleted.

·     Serial number changed.

·     Processed join request in Run state.

·     Failed to retransmit message.

·     Received WTP tunnel down event from AP.

·     Backup AC closed the backup tunnel.

·     Tunnel switched.

·     N/A.

Severity level

6

Example

APMGR/6/APMGR_CWS_TUNNEL_DOWN: CAPWAP tunnel to AP ap1 went down. Reason: AP was reset.

Explanation

The AP went offline for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the AP and the AC.

2.     Verify that the AP is correctly configured.

3.     Verify that the AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWS_TUNNEL_UP

Message text

[STRING] CAPWAP tunnel to AP [STRING] went up.

Variable fields

$1: Tunnel type:

·     Master.

·     Backup.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_CWS_TUNNEL_UP: Backup CAPWAP tunnel to AP ap1 went up.

Explanation

The AP came online and entered Run state.

Recommended action

No action is required.

 

APMGR_DELBAC_INFO

Message text

Delete BAS AC [STRING].

Variable fields

$1: MAC address of the BAS AC.

Severity level

6

Example

APMGR/6/APMGR_DELBAC_INFO: Delete BAS AC 3ce5-a616-28cd.

Explanation

The BAS AC was disconnected from the master AC.

Recommended action

No action is required.

 

APMGR_LOCAL_AC_OFFLINE

Message text

Local AC [STRING] went offline. State changed to Idle.

Variable fields

$1: Name of the local AC.

Severity level

6

Example

APMGR/6/APMGR_LOCAL_AC_OFFLINE: Local AC ac1 went offline. State changed to Idle.

Explanation

The local AC went offline. The state of the local AC changed to Idle.

Recommended action

1.     If the local AC went offline abnormally, check the debugging information to locate the issue and resolve it.

2.     If the issue persists, contact H3C Support.

 

APMGR_LOCAL_AC_ONLINE

Message text

Local AC [STRING] went online. State changed to Run.

Variable fields

$1: Name of the local AC.

Severity level

6

Example

APMGR/6/APMGR_LOCAL_AC_ONLINE: Local AC ac1 went online. State changed to Run.

Explanation

The local AC came online. The state of the local AC changed to Run.

Recommended action

No action is required.

 

ARP messages

This section contains ARP messages.

ARP_ACTIVE_ACK_NO_REPLY

Message text

No ARP reply from IP [STRING] was received on interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_ACTIVE_ACK_NO_REPLY: No ARP reply from IP 192.168.10.1 was received on interface GigabitEthernet1/0/1.

Explanation

The ARP active acknowledgement feature did not receive an ARP reply after it sent an ARP request to the sender IP of an ARP message.

This message indicates the risk of attacks.

Recommended action

1.     Verify that the learned ARP entries on the device are consistent with the existing legal devices. When gateways and servers are on the network, check the ARP entries for these devices first.

2.     If the ARP entries are correct and the attack continues, contact H3C Support.

 

ARP_ACTIVE_ACK_NOREQUESTED_REPLY

Message text

Interface [STRING] received from IP [STRING] an ARP reply that was not requested by the device.

Variable fields

$1: Interface name.

$2: IP address.

Severity level

6

Example

ARP/6/ARP_ACTIVE_ACK_NOREQUESTED_REPLY: Interface GigabitEthernet1/0/1 received from IP 192.168.10.1 an ARP reply that was not requested by the device.

Explanation

The ARP active acknowledgement feature received an unsolicited ARP reply from a sender IP.

This message indicates the risk of attacks.

Recommended action

No action is required. The device discards the ARP reply automatically.

 

ARP_BINDRULETOHW_FAILED

Message text

Failed to download binding rule to hardware on the interface [STRING], SrcIP [IPADDR], SrcMAC [MAC], VLAN [UINT16], Gateway MAC [MAC].

Variable fields

$1: Interface name.

$2: Source IP address.

$3: Source MAC address.

$4: VLAN ID.

$5: Gateway MAC address.

Severity level

5

Example

ARP/5/ARP_BINDRULETOHW_FAILED: Failed to download binding rule to hardware on the interface GigabitEthernet1/0/1, SrcIP 1.1.1.132, SrcMAC 0015-E944-A947, VLAN 1, Gateway MAC 00A1-B812-1108.

Explanation

The system failed to set a binding rule to the hardware on an interface. The message is sent in any of the following situations:

·     The resources are not sufficient for the operation.

·     The memory is not sufficient for the operation.

·     A hardware error occurs.

Recommended action

To resolve the problem:

1.     Execute the display qos-acl resource command to check if the ACL resources for the operation are sufficient.

¡     If yes, proceed to step 2.

¡     If no, delete unnecessary configuration to release ACL resources. If no configuration can be deleted, proceed to step 2.

2.     Execute the display memory command to check if the memory for the operation is sufficient.

¡     If yes, proceed to step 3.

¡     If no, delete unnecessary configuration to release memory. If no configuration can be deleted, proceed to step 3.

3.     Delete the configuration and perform the operation again.

 

ARP_DETECTION_LOG

Message text

Detected an ARP attack on interface [STRING]: IP [STRING], MAC [STRING], VLAN [STRING]. [UINT32] packet(s) dropped.

Variable fields

$1: Interface name.

$2: IP address.

$3: MAC address.

$4: VLAN ID.

$5: Number of dropped packets.

Severity level

5

Example

ARP/5/ARP_INSPECTION: -MDC=1; Detected an ARP attack on interface GigabitEthernet1/0/1: IP 1.1.1.1, MAC 1-1-1, VLAN 100. 2 packet(s) dropped.

Explanation

An ARP attack was detected on an interface and attack packets were dropped.

Recommended action

Check the source of the ARP attack.

 

ARP_DUPLICATE_IPADDR_DETECT

Message text

Detected an IP address conflict. The device with MAC address [STRING] connected to interface [STRING] in VSI [STRING] and the device with MAC address [STRING] connected to interface [STRING] in VSI [STRING] were using the same IP address [IPADDR].

Variable fields

$1: MAC address.

$2: Interface name. (The interface can be a tunnel interface, Layer 3 interface, or Ethernet service instance.)

$3: VSI name.

$4: MAC address.

$5: Interface name. (The interface can be a tunnel interface, Layer 3 interface, or Ethernet service instance.)

$6: VSI name.

$7: Conflicting IP address.

Severity level

4

Example

ARP/4/ARP_DUPLICATE_IPADDR_DETECT: Detected an IP address conflict. The device with MAC address 00-00-01 connected to interface GigabitEthernet1/0/1 service-instance 1000 in VSI vpna and the device with MAC address 00-00-02 connected to interface tunnel 10 in VSI vpna were using the same IP address 192.168.1.1.

Explanation

This message is sent when an interface receives an ARP message in which the sender information conflicts with an existing ARP entry. The sender IP address is the same as the IP address in the entry, but the MAC addresses are different.

Recommended action

Change the IP address on either of the two devices.

 

ARP_DYNAMIC

Message text

The maximum number of dynamic ARP entries for the device reached.

Variable fields

N/A

Severity level

6

Example

ARP/6/ARP_DYNAMIC: The maximum number of dynamic ARP entries for the device reached.

Explanation

The maximum number of dynamic ARP entries for the device was reached.

Recommended action

No action is required.

 

ARP_DYNAMIC_IF

Message text

The maximum number of dynamic ARP entries for interface [STRING] reached.

Variable fields

$1: Interface name.

Severity level

6

Example

ARP/6/ARP_DYNAMIC_IF: The maximum number of dynamic ARP entries for interface GigabitEthernet1/0/1 reached.

Explanation

The maximum number of dynamic ARP entries for the specified interface was reached.

Recommended action

No action is required.

 

ARP_DYNAMIC_SLOT

Message text

Pattern 1:

The maximum number of dynamic ARP entries for slot [INT32] reached.

Pattern 2:

The maximum number of dynamic ARP entries for chassis [INT32] slot [INT32] reached.

Variable fields

Pattern 1:

$1: Slot number.

Pattern 2:

$1: Chassis number.

$2: Slot number.

Severity level

6

Example

ARP/6/ARP_DYNAMIC_SLOT: The maximum number of dynamic ARP entries for slot 2 reached.

Explanation

Pattern 1:

The maximum number of dynamic ARP entries for the slot was reached.

Pattern 2:

The maximum number of dynamic ARP entries for the slot on the chassis was reached.

Recommended action

No action is required.

 

ARP_ENTRY_CONFLICT

Message text

The software entry for [STRING] on [STRING] and the hardware entry did not have the same [STRING].

Variable fields

$1: IP address.

$2: VPN instance name. If the ARP entry belongs to the public network, this field displays the public network.

$3: Inconsistent items:

¡     MAC address.

¡     output interface.

¡     output port.

¡     outermost layer VLAN ID.

¡     second outermost layer VLAN ID.

¡     VSI index.

¡     link ID.

Severity level

6

Example

ARP/6/ARP_ENTRY_CONFLICT: The software entry for 1.1.1.1 on the VPN a and the hardware entry did not have the same MAC address, output port, VSI index, and link ID.

ARP/6/ARP_ENTRY_CONFLICT: The software entry for 1.1.1.2 on the public  network and the hardware entry did not have the same MAC address, output port, VSI index, and link ID.

Explanation

The software entry for the specified IP address is not the same as the hardware entry. For example, they do not have the same output interface.

Recommended action

No action is required. ARP automatically refreshes the hardware entries.

 

ARP_HOST_IP_CONFLICT

Message text

The host [STRING] connected to interface [STRING] cannot communicate correctly, because it uses the same IP address as the host connected to interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: Interface name.

Severity level

4

Example

ARP/4/ARP_HOST_IP_CONFLICT: The host 1.1.1.1 connected to interface GigabitEthernet1/0/1 cannot communicate correctly, because it uses the same IP address as the host connected to interface GigabitEthernet1/0/2.

Explanation

The sender IP address in a received ARP message conflicted with the IP address of a host connected to another interface.

Recommended action

Check whether the hosts that send the ARP messages are legitimate. Disconnect the illegal host from the network.

 

ARP_LOCALPROXY_ENABLE_FAILED

Message text

Failed to enable local proxy ARP on interface [STRING].

Variable fields

$1: Interface name.

Severity level

4

Example

ARP/4/ARP_LOCALPROXY_ENABLE_FAILED: -MDC=1-Slot=2; Failed to enable local proxy ARP on interface VSI-interface 1.

Explanation

This message is sent when the device fails to enable local proxy ARP on an interface in a slot. If the interface resides on the MPU, the slot number is 0.

Recommended action

1.     Verify that the card supports local proxy ARP.

2.     Verify that sufficient hardware resources are available.

 

ARP_RATE_EXCEEDED

Message text

The ARP packet rate ([UINT32] pps) exceeded the rate limit ([UINT32] pps) on interface [STRING] in the last [UINT32] seconds.

Variable fields

$1: ARP packet rate.

$2: ARP limit rate.

$3: Interface name.

$4: Interval time.

Severity level

4

Example

ARP/4/ARP_RATE_EXCEEDED: The ARP packet rate (100 pps) exceeded the rate limit (80 pps) on interface GigabitEthernet1/0/1 in the last 10 seconds.

Explanation

An interface received ARP messages at a higher rate than the rate limit.

Recommended action

Verify that the hosts at the sender IP addresses are legitimate.

 

ARP_RATELIMIT_NOTSUPPORT

Message text

Pattern 1:

ARP packet rate limit is not support on slot [INT32].

Pattern 2:

ARP packet rate limit is not support on chassis [INT32] slot [INT32].

Variable fields

Pattern 1:

$1: Slot number.

Pattern 2:

$1: Chassis number.

$2: Slot number.

Severity level

6

Example

ARP/6/ARP_RATELIMIT_NOTSUPPORT: ARP packet rate limit is not support on slot 2.

Explanation

Pattern 1:

ARP packet rate limit is not supported on the slot.

Pattern 2:

ARP packet rate limit is not supported on the slot of the chassis was reached.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_SENDER_IP_INVALID

Message text

Sender IP [STRING] was not on the same network as the receiving interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_SENDER_IP_INVALID: Sender IP 192.168.10.2 was not on the same network as the receiving interface GigabitEthernet1/0/1.

Explanation

The sender IP of a received ARP message was not on the same network as the receiving interface.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_SENDER_MAC_INVALID

Message text

Sender MAC [STRING] was not identical to Ethernet source MAC [STRING] on interface [STRING].

Variable fields

$1: MAC address.

$2: MAC address.

$3: Interface name.

Severity level

6

Example

ARP/6/ARP_SENDER_MAC_INVALID: Sender MAC 0000-5E14-0E00 was not identical to Ethernet source MAC 0000-5C14-0E00 on interface GigabitEthernet1/0/1.

Explanation

An interface received an ARP message. The sender MAC address in the message body was not identical to the source MAC address in the Ethernet header.

Recommended action

Verify that the host at the sender MAC address is legitimate.

 

ARP_SENDER_SMACCONFLICT

Message text

Packet was discarded because its sender MAC address was the MAC address of the receiving interface.

Interface: [STRING], sender IP: [STRING], target IP: [STRING].

Variable fields

$1: Interface name.

$2: Sender IP address.

$3: Target IP address.

Severity level

6

Example

ARP/6/ ARP_SENDER_SMACCONFLICT: Packet discarded for the sender MAC address is the same as the receiving interface.

Interface: GigabitEthernet1/0/1 sender IP: 1.1.2.2 target IP: 1.1.2.1,

Explanation

The sender MAC address of a received ARP packet conflicts with the MAC address of the device.

Recommended action

No action is required.

 

ARP_SENDER_SMACCONFLICT_VSI

Message text

Packet was discarded because its sender MAC address was the MAC address of the receiving interface.

Interface: [STRING], sender IP: [STRING], target IP: [STRING],VSI index: [UINT32], link ID: [UINT32].

Variable fields

$1: Interface name.

$2: Sender IP address.

$3: Target IP address.

$4: VSI index.

$5: Link ID.

Severity level

6

Example

ARP/6/ ARP_SENDER_SMACCONFLICT_VSI: Packet discarded for the sender MAC address is the same as the receiving interface.

Interface: VSI3 sender IP: 1.1.2.2 target IP: 1.1.2.1, VSI Index: 2, Link ID: 0

Explanation

The sender MAC address of a received ARP packet conflicts with the MAC address of the device. The receiving interface is a VSI interface.

Recommended action

No action is required.

 

ARP_SRC_MAC_FOUND_ATTACK

Message text

An attack from MAC [STRING] was detected on interface [STRING].

Variable fields

$1: MAC address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_SRC_MAC_FOUND_ATTACK: An attack from MAC 0000-5E14-0E00 was detected on interface GigabitEthernet1/0/1.

Explanation

The source MAC-based ARP attack detection feature received more ARP packets from the same MAC address within 5 seconds than the specified threshold.

This message indicates the risk of attacks.

Recommended action

Verify that the host at the source MAC address is legitimate.

 

ARP_SUP_ENABLE_FAILED

Message text

Failed to enable ARP flood suppression on VSI [STRING].

Variable fields

$1: VSI name.

Severity level

4

Example

ARP/4/ARP_SUP_ENABLE_FAILED: -MDC=1; Failed to enable ARP flood suppression on VSI vpna.

Explanation

This message is sent when the system failed to enable ARP flood suppression for a VSI. The minimum interval between two log messages is 2 seconds. To make the system send the message successfully, wait for a minimum of 2 seconds before you enable ARP flood suppression for another VSI.

Recommended action

1.     Verify that the device supports ARP flood suppression.

2.     Verify that the hardware resources are sufficient.

 

ARP_TARGET_IP_INVALID

Message text

Target IP [STRING] was not the IP of the receiving interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_TARGET_IP_INVALID: Target IP 192.168.10.2 was not the IP of the receiving interface GigabitEthernet1/0/1.

Explanation

The target IP address of a received ARP message was not the IP address of the receiving interface.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_THRESHOLD_REACHED

Message text

The alarm threshold for dynamic ARP entry learning was reached on interface [STRING].

Variable fields

$1: Interface name.

Severity level

4

Example

ARP/4/ARP_THRESHOLD_REACHED: The alarm threshold for dynamic ARP entry learning was reached on interface GigabitEthernet1/0/1.

Explanation

This message is sent when the alarm threshold for dynamic ARP learning was reached on GigabitEthernet 1/0/1.

Recommended action

Verify that the number of learned dynamic ARP entries matches the actual number of devices in the network and no ARP attack sources exist in the network.

 

ARP_USER_DUPLICATE_IPADDR_DETECT

Message text

Detected a user IP address conflict. New user (MAC [STRING], SVLAN [STRING], CVLAN [STRING]) on interface [STRING] and old user (MAC [STRING], SVLAN [STRING], CVLAN [STRING]) on interface [STRING] were using the same IP address [IPADDR].

Variable fields

$1: MAC address of a new user.

$2: Outer VLAN to which the new user belongs.

$3: Inner VLAN to which the new user belongs.

$4: Name of the interface connecting to the new user.

$5: MAC address of an old user.

$6: Outer VLAN to which the old user belongs.

$7: Inner VLAN to which the old user belongs.

$8: Name of the interface connecting to the old user.

$9: IP address.

Severity level

6

Example

ARP/6/ARP_USER_DUPLICATE_IPADDR_DETECT: Detected a user IP address conflict. New user (MAC 0010-2100-01e1, SVLAN 100, CVLAN 10) on interface GigabitEthernet1/0/1 and old user (MAC 0120-1e00-0102, SVLAN 100, CVLAN 10) on interface GigabitEthernet1/0/1 were using the same IP address 192.168.1.1.

Explanation

ARP detected a user IP address conflict. The IP address of a new user is the same as the IP address of an old user.

Recommended action

Verify that all users have different IP addresses.

 

ARP_USER_MOVE_DETECT

Message text

Detected a user (IP address [IPADDR], MAC address [STRING]) moved to another interface. Before user move: interface [STRING], SVLAN [STRING], CVLAN [STRING]. After user move: interface [STRING], SVLAN [STRING], CVLAN [STRING].

Variable fields

$1: IP address of the user.

$2: MAC address of the user.

$3: Interface name before the migration.

$4: Outer VLAN to which the user belongs before the migration.

$5: Inner VLAN to which the user belongs before the migration.

$6: Interface name after the migration.

$7: Outer VLAN to which the user belongs after the migration.

$8: Inner VLAN to which the user belongs after the migration.

Severity level

6

Example

ARP/6/ARP_USER_MOVE_DETECT: Detected a user (IP address 192.168.1.1, MAC address 0010-2100-01e1) moved to another interface. Before user move: interface GigabitEthernet1/0/1, SVLAN 100, CVLAN 10. After user move: interface GigabitEthernet1/0/2, SVLAN 100, CVLAN 10.

Explanation

ARP detected a user accesses the network through another port.

Recommended action

Use the display arp user-move record command to verify that the migration is legitimate.

 

DUPIFIP

Message text

Duplicate address [STRING] on interface [STRING], sourced from [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: MAC Address.

Severity level

6

Example

ARP/6/DUPIFIP: Duplicate address 1.1.1.1 on interface GigabitEthernet1/0/1, sourced from 0015-E944-A947.

Explanation

ARP detected a duplicate address.

The sender IP in the received ARP packet was being used by the receiving interface.

Recommended action

Modify the IP address configuration.

 

DUPIP

Message text

IP address [STRING] conflicted with global or imported IP address, sourced from [STRING].

Variable fields

$1: IP address.

$2: MAC Address.

Severity level

6

Example

ARP/6/DUPIP: IP address 30.1.1.1 conflicted with global or imported IP address, sourced from 0000-0000-0001.

Explanation

The sender IP address of the received ARP packet conflicted with the global or imported IP address.

Recommended action

Modify the IP address configuration.

 

DUPVRRPIP

Message text

IP address [STRING] conflicted with VRRP virtual IP address on interface [STRING], sourced from [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: MAC address.

Severity level

6

Example

ARP/6/DUPVRRPIP: IP address 1.1.1.1 conflicted with VRRP virtual IP address on interface GigabitEthernet1/0/1, sourced from 0015-E944-A947.

Explanation

The sender IP address of the received ARP packet conflicted with the VRRP virtual IP address.

Recommended action

Modify the IP address configuration.

 

 

ATK messages

This section contains attack detection and prevention messages.

ATK_ICMP_ADDRMASK_REQ

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ: IcmpType(1058)=17; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_RAW: IcmpType(1058)=17; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask request is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_RAW_SZ: IcmpType(1058)=17; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask request is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_SZ: IcmpType(1058)=17; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL: IcmpType(1058)=18; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL_RAW: IcmpType(1058)=18; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask reply is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields