10-High Availability Command Reference

HomeSupportResource CenterH3C S6520X & S6520-SI & S5560X-HI & S5000-EI Switch Series Command References-R65xx-6W10010-High Availability Command Reference
03-DLDP commands
Title Size Download
03-DLDP commands 81.65 KB

DLDP commands

display dldp

Use display dldp to display DLDP configuration.

Syntax

display dldp [ interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify this option, the command displays global and port-specific DLDP configuration.

Examples

# Display global and port-specific DLDP configuration.

<Sysname> display dldp

 DLDP global status: Enabled

 DLDP advertisement interval: 5s

 DLDP authentication-mode: Simple

 DLDP authentication-password: ******

 DLDP unidirectional-shutdown mode: Auto

 DLDP delaydown-timer value: 1s

 Number of enabled ports: 2

 

Interface Ten-GigabitEthernet1/0/1

 DLDP port state: Bidirectional

 DLDP port unidirectional-shutdown mode: None

 DLDP initial-unidirectional-delay: 100s

 Number of the port’s neighbors: 1

  Neighbor MAC address: 0023-8956-3600

  Neighbor port index: 79

  Neighbor state: Confirmed

  Neighbor aged time: 13s

  Neighbor echo time: -

 

Interface Ten-GigabitEthernet1/0/2

 DLDP port state: Inactive

 DLDP port unidirectional-shutdown mode: None

 DLDP initial-unidirectional-delay: 100s

 Number of the port’s neighbors: 0 (Maximum number ever detected: 1)

# Display the DLDP configuration of Ten-GigabitEthernet 1/0/1.

<Sysname> display dldp interface ten-gigabitethernet 1/0/1

Interface Ten-GigabitEthernet1/0/1

 DLDP port state: Bidirectional

 DLDP port unidirectional-shutdown mode: None

 DLDP initial-unidirectional-delay: 100s

 Number of the port’s neighbors: 1

  Neighbor MAC address: 0023-8956-3600

  Neighbor port index: 79

  Neighbor state: Confirmed

  Neighbor aged time: 13s

  Neighbor echo time: -

Table 1 Command output

Field

Description

DLDP global status

Global DLDP state (Enabled or Disabled).

DLDP advertisement interval

Interval for sending Advertisement packets (in seconds) to maintain neighbor relations.

DLDP authentication-mode

DLDP authentication mode (None, Simple, or MD5).

DLDP authentication-password

Password for DLDP authentication:

·     ******—The password has been configured.

·     Not configured—The authentication mode has been configured but no password is configured.

DLDP unidirectional-shutdown mode

Global port shutdown mode (auto, manual, or hybrid) after unidirectional links are detected.

DLDP port unidirectional-shutdown mode

Port shutdown mode for the interface (auto, manual, or hybrid) after unidirectional links are detected. If no port shutdown mode is configured for an interface, this field displays None.

DLDP delaydown-timer value

Setting of the DelayDown timer, in seconds.

Number of enabled ports

Number of the DLDP-enabled ports.

Interface

Index of a DLDP-enabled port.

DLDP port state

DLDP state on a port:

·     Bidirectional.

·     Inactive.

·     Initial.

·     Unidirectional.

DLDP initial-unidirectional-delay

Delay time in seconds for DLDP to block the interface upon an Initial-to-Unidirectional state transition.

Number of the port’s neighbors

Current number of neighbors.

Maximum number ever detected

Maximum number of neighbors once detected on the port. This field appears only when the current number of neighbors is different from the maximum number of neighbors once detected.

Neighbor MAC address

Bridge MAC address of the device where the neighbor resides.

Neighbor port index

Neighbor port index.

Neighbor state

Neighbor state (Confirmed or Unconfirmed).

Neighbor aged time

Neighbor aging time.

Neighbor echo time

Number of seconds remaining before the Echo timer expires.

The Echo timer starts when the Entry timer expires. The neighbor information is deleted when the Echo timer expires. A hyphen (-) indicates that the Echo timer has not started.

display dldp statistics

Use display dldp statistics to display DLDP packet statistics.

Syntax

display dldp statistics [ interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify this option, the command displays DLDP packet statistics for all interfaces.

Examples

# Display DLDP packet statistics for all interfaces.

<Sysname> display dldp statistics

Interface Ten-GigabitEthernet1/0/1

 Packets sent: 6

 Packets received: 5

 Invalid packets received: 2

 Loopback packets received: 0

 Authentication-failed packets received: 0

 Valid packets received: 3

 

Interface Ten-GigabitEthernet1/0/2

 Packets sent: 7

 Packets received: 7

 Invalid packets received: 3

 Loopback packets received: 0

 Authentication-failed packets received: 0

 Valid packets received: 4

Table 2 Command output

Field

Description

Interface

Port index.

Packets sent

Total number of DLDP packets sent.

Packets received

Total number of DLDP packets received.

Invalid packets received

Number of the invalid packets received.

Loop packets received

Number of the loopback packets received.

Authentication failed packets received

Number of the received packets that failed to pass the authentication.

Valid packets received

Number of the valid packets received.

Related commands

reset dldp statistics

dldp authentication-mode

Use dldp authentication-mode to configure DLDP authentication.

Use undo dldp authentication-mode to restore the default.

Syntax

dldp authentication-mode { md5 | none | simple }

undo dldp authentication-mode

Default

DLDP authentication mode is none.

Views

System view

Predefined user roles

network-admin

Parameters

md5: Specifies the MD5 authentication mode.

none: Specifies not to perform authentication.

simple: Specifies the plaintext authentication mode.

Usage guidelines

To enable DLDP to operate correctly, make sure the DLDP authentication modes and the passwords configured on the two ends of a link are the same.

If you do not configure the authentication password after you configure the authentication mode, the authentication mode is none no matter which authentication mode you configure.

Examples

# Configure to perform plaintext authentication and set the password to abc (assuming that Device A and Device B are connected by a DLDP link).

·     Configure Device A:

<DeviceA> system-view

[DeviceA] dldp authentication-mode simple

[DeviceA] dldp authentication-password simple abc

·     Configure Device B:

<DeviceB> system-view

[DeviceB] dldp authentication-mode simple

[DeviceB] dldp authentication-password simple abc

Related commands

display dldp

dldp authentication-password

dldp authentication-password

Use dldp authentication-password to configure the password for DLDP authentication.

Use undo dldp authentication-password to restore the default.

Syntax

dldp authentication-password { cipher | simple } string

undo dldp authentication-password

Default

No DLDP authentication password is configured.

Views

System view

Predefined user roles

network-admin

Parameters

cipher: Specifies a password in encrypted form.

simple: Specifies a password in plaintext form. For security purposes, the password specified in plaintext form will be stored in encrypted form.

string: Specifies the password. Its plaintext form is a case-sensitive string of 1 to 16 characters. Its encrypted form is a case-sensitive string of 1 to 53 characters.

Usage guidelines

To enable DLDP to operate correctly, make sure the DLDP authentication modes and the passwords configured on the two ends of a link are the same.

If you do not configure the authentication password after you configure the authentication mode, the authentication mode is none no matter which authentication mode you configure.

Examples

# Configure to perform plaintext authentication and set the password to abc (assuming that Device A and Device B are connected by a DLDP link).

·     Configure Device A:

<DeviceA> system-view

[DeviceA] dldp authentication-mode simple

[DeviceA] dldp authentication-password simple abc

·     Configure Device B:

<DeviceB> system-view

[DeviceB] dldp authentication-mode simple

[DeviceB] dldp authentication-password simple abc

Related commands

display dldp

dldp authentication-mode

dldp delaydown-timer

Use dldp delaydown-timer to set the DelayDown timer.

Use undo dldp delaydown-timer to restore the default.

Syntax

dldp delaydown-timer time

undo dldp delaydown-timer

Default

The setting of the DelayDown timer is 1 second.

Views

System view

Predefined user roles

network-admin

Parameters

time: Specifies the DelayDown timer in the range of 1 to 5 seconds.

Usage guidelines

The DelayDown timer configured by using this command applies to all DLDP-enabled ports.

Examples

# Set the DelayDown timer to 2 seconds.

<Sysname> system-view

[Sysname] dldp delaydown-timer 2

Related commands

display dldp

dldp enable

Use dldp enable to enable DLDP on a port.

Use undo dldp enable to restore the default.

Syntax

dldp enable [ initial-unidirectional-delay time ]

undo dldp enable

Default

DLDP is disabled on a port, and when DLDP is enabled, a port is blocked immediately upon an Initial-to-Unidirectional state transition.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

initial-unidirectional-delay time: Specifies the delay time for DLDP to block a port upon an Initial-to-Unidirectional state transition. The value range for the time argument is 60 to 300 seconds. If you do not specify this option, DLDP blocks the port immediately upon an Initial-to-Unidirectional state transition.

Usage guidelines

DLDP can take effect only after you enable it globally and on a port.

When enabling DLDP on a port, you can set the delay time for DLDP to block the port upon an Initial-to-Unidirectional state transition. If the port does not enter Bidirectional state when the delay time expires, DLDP blocks the port.

Examples

# Enable DLDP globally, and enable DLDP on Ten-GigabitEthernet 1/0/1 and set a delay time of 100 seconds for DLDP to block the port upon an Initial-to-Unidirectional state transition.

<Sysname> system-view

[Sysname] dldp global enable

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] dldp enable initial-unidirectional-delay 100

Related commands

display dldp

dldp global enable

dldp global enable

Use dldp global enable to enable DLDP globally.

Use undo dldp global enable to disable DLDP globally.

Syntax

dldp global enable

undo dldp global enable

Default

DLDP is disabled globally.

Views

System view

Predefined user roles

network-admin

Usage guidelines

DLDP can take effect only after you enable it globally and on a port.

Examples

# Enable DLDP globally.

<Sysname> system-view

[Sysname] dldp global enable

Related commands

display dldp

dldp enable

dldp interval

Use dldp interval to set the interval for sending Advertisement packets.

Use undo dldp interval to restore the default.

Syntax

dldp interval interval

undo dldp interval

Default

The interval for sending Advertisement packets is 5 seconds.

Views

System view

Predefined user roles

network-admin

Parameters

interval: Specifies Advertisement packets sending interval in the range of 1 to 100 seconds.

Usage guidelines

This command applies to all DLDP-enabled ports.

To enable DLDP to operate correctly, make sure the intervals for sending Advertisement packets configured on the two ends of a link are the same.

Examples

# Set the interval for sending Advertisement packets to 20 seconds.

<Sysname> system-view

[Sysname] dldp interval 20

Related commands

display dldp

dldp port unidirectional-shutdown

Use dldp port unidirectional-shutdown to set the port shutdown mode for an interface.

Use undo dldp port unidirectional-shutdown to restore the default.

Syntax

dldp port unidirectional-shutdown { auto | hybrid | manual }

undo dldp port unidirectional-shutdown

Default

The global setting is used.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

auto: Specifies the auto mode. In this mode, when DLDP detects a unidirectional link, it shuts down the unidirectional port. When the link becomes bidirectional, DLDP brings up the port that was shut down.

hybrid: Specifies the hybrid mode. In this mode, when DLDP detects a unidirectional link, it shuts down the unidirectional port and stops link detection. To verify the link status, use the undo shutdown command to bring up the port. If the link becomes bidirectional, the port becomes bidirectional.

manual: Specifies the manual mode. In this mode, when DLDP detects a unidirectional link, it does not shut down the involved port. You must manually shut it down. To verify the link status, use the undo shutdown command to bring up the port. If the link becomes bidirectional, the port becomes bidirectional.

Usage guidelines

If DLDP detects a unidirectional link, you must troubleshoot the interface and cabling faults.

The port shutdown mode setting for an interface takes effect only on the current interface and has priority over the global port shutdown mode setting.

Examples

# Set the port shutdown mode to manual for Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] dldp port unidirectional-shutdown manual

Related commands

display dldp

dldp unidirectional-shutdown

dldp unidirectional-shutdown

Use dldp unidirectional-shutdown to set the global port shutdown mode.

Use undo dldp unidirectional-shutdown to restore the default.

Syntax

dldp unidirectional-shutdown { auto | hybrid | manual }

undo dldp unidirectional-shutdown

Default

The global port shutdown mode is auto mode.

Views

System view

Predefined user roles

network-admin

Parameters

auto: Specifies the auto mode. In this mode, when DLDP detects a unidirectional link, it shuts down the unidirectional port. When the link becomes bidirectional, DLDP brings up the port that was shut down.

hybrid: Specifies the hybrid mode. In this mode, when DLDP detects a unidirectional link, it shuts down the unidirectional port and stops link detection. To verify the link status, use the undo shutdown command to bring up the port. If the link becomes bidirectional, the port becomes bidirectional.

manual: Specifies the manual mode. In this mode, when DLDP detects a unidirectional link, it does not shut down the involved port. You must manually shut it down. To verify the link status, use the undo shutdown command to bring up the port. If the link becomes bidirectional, the port becomes bidirectional.

Usage guidelines

If DLDP detects a unidirectional link, you must troubleshoot the interface and cabling faults.

The global port shutdown mode setting takes effect on all interfaces and has lower priority than the port shutdown mode setting for an interface.

Examples

# Set the global port shutdown mode to manual mode.

<Sysname> system-view

[Sysname] dldp unidirectional-shutdown manual

Related commands

display dldp

dldp port unidirectional-shutdown

reset dldp statistics

Use reset dldp statistics to clear DLDP packet statistics.

Syntax

reset dldp statistics [ interface interface-type interface-number ]

Views

User view

Predefined user roles

network-admin

Parameters

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify this option, the command clears DLDP packet statistics for all interfaces.

Examples

# Clear DLDP packet statistics for all interfaces.

<Sysname> reset dldp statistics

Related commands

display dldp statistics