11-Network Management and Monitoring Command Reference

HomeSupportResource CenterH3C S6520X-HI[EI][SI] & S6520-SI & S5560X-HI & S5000-EI & MS4600 Switch Series Command References-R63xx-6W10111-Network Management and Monitoring Command Reference
20-VCF fabric commands
Title Size Download
20-VCF fabric commands 119.82 KB

VCF fabric commands

The following switch series do not support VCF fabric:

·     S6520X-SI

·     S6520-SI

·     S5000-EI

·     MS4600

border enable

Use border enable to enable the border node service.

Use undo border enable to disable the border node service.

Syntax

border enable

undo border enable

Default

The device is not a border node.

Views

Neutron view

Predefined user roles

network-admin

Usage guidelines

The external network and routers are created and deleted on the OpenStack Dashboard. Use this command to configure the device as a border node. The device automatically deploys the routing configurations made on the OpenStack Dashboard and implements connectivity between tenant networks and the external network.

On a VXLAN network with a centralized IP gateway or on a VLAN network, use this command on spine nodes. On a VXLAN network with distributed IP gateways, use this command on leaf nodes.

Examples

# Enable the border node service.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron] border enable

display vcf-fabric role

Use display vcf-fabric role to display the role of the device in the VCF fabric.

Syntax

display vcf-fabric role

Views

Any view

Predefined user roles

network-admin

network-operator

Usage guidelines

Use this command to display the default role and the current role of the device in the VCF fabric. To change the current role of the device, use the vcf-fabric role command.

Examples

# Display the role of the device in the VCF fabric.

<System> display vcf-fabric role

Default role: leaf

Current role: leaf

Table 1 Command output

Field

Description

Default role

Default role of the device:

·     spine—The device is a spine node.

·     leaf—The device is a leaf node.

·     access—The device is an access node.

Current role

Current role of the device:

·     spine—The device is a spine node.

·     leaf—The device is a leaf node.

·     access—The device is an access node.

 

Related commands

vcf-fabric role

display vcf-fabric topology

Use display vcf-fabric topology to display VCF fabric topology information.

Syntax

display vcf-fabric topology

Views

Any view

Predefined user roles

network-admin

network-operator

Usage guidelines

This command displays VCF fabric topology information only when it is executed on the master spine node.

Before you display VCF fabric topology information, make sure VCF fabric topology discovery and automated underlay network deployment are enabled.

Examples

# Display VCF fabric topology information.

<Sysname> display vcf-fabric topology

                                  Topology Information

----------------------------------------------------------------------------------

* indicates the master spine role among all spines

SpineIP            Interface                      Link LeafIP              Status

*10.11.113.51     Ten-GigabitEthernet1/0/1       Up   10.11.113.52       Deploying

                  Ten-GigabitEthernet1/0/2       Down --                   --

                  Ten-GigabitEthernet1/0/3       Down --                   --

                  Ten-GigabitEthernet1/0/4       Down --                   --

                  Ten-GigabitEthernet1/0/5       Up   10.11.113.53       Deploying

                  Ten-GigabitEthernet1/0/6       Down --                   --

                  Ten-GigabitEthernet1/0/7       Down --                   --

                  Ten-GigabitEthernet1/0/8       Down --                   --

Table 2 Command output

Field

Description

SpineIP

IPv4 address of the management Ethernet interface on the spine node. This field displays an asterisk (*) before the IP address if the device is the master spine node.

Interface

Interface through which the spine node connects to a leaf node.

If the device is a master spine node, all interfaces on the device are displayed.

Link

Physical link state of the interface.

LeafIP

IPv4 address of the interface through which a leaf node connects to the spine node.

Status

Status of automated underlay network deployment on the leaf node.

This field displays two hyphens (--) if automated underlay network deployment is not started.

This field displays Deploying if automated underlay network deployment is in progress.

 

Related commands

vcf-fabric underlay autoconfigure

vcf-fabric topology enable

display vcf-fabric underlay autoconfigure

Use display vcf-fabric underlay autoconfigure to display information about automated underlay network deployment.

Syntax

display vcf-fabric underlay autoconfigure

Views

Any view

Predefined user roles

network-admin

network-operator

Usage guidelines

Before you execute this command, make sure automated underlay network deployment is enabled.

Examples

# Display information about automated underlay network deployment.

<Sysname> display vcf-fabric underlay autoconfigure

success command:

         #

           system

           clock timezone beijing add 08:00:00

         #

           system

           lldp global enable

           lldp compliance cdp

         #

           system

           ospf 1

           non-stop-routing

           area 0.0.0.0

         #

           system

           interface LoopBack0

         #

           system

           l2vpn enable

         #

           system

           vxlan tunnel mac-learning disable

           vxlan tunnel arp-learning disable

         #

           system

           ovsdb server ptcp port 6632

           ovsdb server enable

         #

           system

           vtep enable

         #

           system

           stp global enable

         #

           system

           ntp-service enable

           ntp-service unicast-server 85.0.0.10 vpn-instance mgmt

         #

           system

           netconf soap https enable

           netconf ssh server enable

           restful https enable

         #

           system

           info-center loghost vpn-instance mgmt 85.0.0.10

         #

           system

           local-user admin

           password ******

           service-type https

           authorization-attribute user-role network-admin

         #

           system

           line vty 0 63

           authentication-mode scheme

           user-role network-admin

         #

           system

           vcf-fabric topology enable

         #

           system

           snmp-agent

           snmp-agent community read public

           snmp-agent community write private

           snmp-agent sys-info version all

           snmp-agent packet max-size 4096

           snmp-agent target-host trap address udp-domain 85.0.0.10 params securityname public v2c

           snmp-agent target-host trap address udp-domain 85.0.0.10 vpn-instance mgmt params securityname public v2c

         #

           system

           telnet server enable

           local-user admin

           password ******

           service-type telnet http https

           authorization-attribute user-role network-admin

         #

           system

           ssh server enable

           local-user admin

           password ******

           service-type ssh http https

           authorization-attribute user-role network-admin

         #

           system

           netconf soap http enable

           netconf soap https enable

           local-user admin

           password ******

           service-type http https

           authorization-attribute user-role network-admin

         #

           system

           bgp 100

           non-stop-routing

           address-family l2vpn evpn

         #

Uplink interface:

         Ten-GigabitEthernet1/0/25

         Ten-GigabitEthernet1/0/26

         Ten-GigabitEthernet5/0/25

         Ten-GigabitEthernet5/0/26

Downlink interface:

         GigabitEthernet1/0/1

         GigabitEthernet1/0/19

         GigabitEthernet5/0/19

         GigabitEthernet5/0/20

Aggregation configurations:

         AggrID: 1024

         interface: GigabitEthernet1/0/19

         interface: GigabitEthernet5/0/19

IRF Allocation:

         Self Bridge Mac: 00e7-fc52-5100

         IRF Status: Yes

         Member List: [1, 5]

         BFD Mad-port pairs: GE1/0/17 , GE5/0/18

BGP peer configuration:

         145.16.17.253

         145.16.17.254

 

Table 3 Command output

Field

Description

success command

Commands that have been successfully executed during automated underlay network deployment.

Uplink interface

Uplink interfaces of the device.

Downlink interface

Downlink interfaces of the device.

AP-side interfaces

Interfaces connected to APs.

Loopback0 IP allocation

IP addresses assigned to Loopback 0.

Loopback1 IP allocation

IP addresses assigned to Loopback 1.

Aggregation configuration

Information about Layer 2 aggregation groups.

IRF allocation

IRF configurations, including IRF bridge MAC address of the IRF fabric, IRF status, and the IRF member ID of the device.

BGP peer configuration

Information about BGP peers of the device.

 

Related commands

vcf-fabric underlay autoconfigure

display vcf-fabric underlay template-version

Use display vcf-fabric underlay template-version to display the supported version and the current version of the template file for automated VCF fabric deployment.

Syntax

display vcf-fabric underlay template-version

Views

Any view

Predefined user roles

network-admin

network-operator

Usage guidelines

The version format of a template file for automated VCF fabric deployment is x.y. Only the x part is examined during a version compatibility check. For successful automated deployment, make sure x in the version of the template file to be used is not greater than x in the supported version.

Examples

# Display the supported version and the current version of the template file for automated VCF fabric deployment when automated deployment is not started.

<Sysname> display vcf-fabric underlay template-version

Supported template version: 6.0

Current template version: Not available

# Display the supported version and the current version of the template file for automated VCF fabric deployment when automated deployment has finished.

<Sysname> display vcf-fabric underlay template-version

Supported template version: 6.0

Current template version: 6.0

Table 4 Command output

Field

Description

Supported template version

Supported version of the template file for automated VCF fabric deployment.

Current template version

Current version of the template file for automated VCF fabric deployment.

This field displays Not available if automated VCF fabric deployment has not started.

This field displays None if automated VCF fabric deployment has finished but the template file does not contain a version number.

 

gateway ip

Use gateway ip to specify the IPv4 address of the border gateway.

Use undo gateway ip to restore the default.

Syntax

gateway ip ipv4-address

undo gateway ip

Default

No IPv4 address is specified for the border gateway.

Views

Neutron view

Predefined user roles

network-admin

Parameters

ipv4-address: Specifies the IPv4 address of the border gateway.

Usage guidelines

Use this command to specify the border gateway IP address for VMs to access the external network. On a VXLAN network with a centralized IP gateway or on a VLAN network, use this command on spine nodes. On a VXLAN network with distributed IP gateways, use this command on leaf nodes.

If you configure this command multiple times, the most recent configuration takes effect.

Examples

# Specify IPv4 address 100.1.1.1 for the border gateway.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron] gateway ip 100.1.1.1

l2agent enable

Use l2agent enable to enable Layer 2 (L2) agent.

Use undo l2agent enable to disable L2 agent.

Syntax

l2agent enable

undo l2agent enable

Default

L2 agent is disabled.

Views

Neutron view

Predefined user roles

network-admin

Usage guidelines

On a VLAN network, use this command on spine nodes and leaf nodes.

On a VXLAN network with a centralized IP gateway, use this command on spine nodes and leaf nodes.

On a VXLAN network with distributed IP gateways, use this command on leaf nodes.

Examples

# Enable L2 agent.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron] l2agent enable

l3agent enable

Use l3agent enable to enable Layer 3 (L3) agent.

Use undo l3agent enable to disable L3 agent.

Syntax

l3agent enable

undo l3agent enable

Default

L3 agent is disabled.

Views

Neutron view

Predefined user roles

network-admin

Usage guidelines

On a VLAN network or on a VXLAN network with a centralized IP gateway, use this command only on spine nodes.

On a VXLAN network with distributed IP gateways, use this command on leaf nodes.

Examples

# Enable L3 agent.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron] l3agent enable

network-type

Use network-type to specify the network type.

Use undo network-type to restore the default.

Syntax

network-type { centralized-vxlan | distributed-vxlan | vlan }

undo network-type

Default

The network type is VLAN.

Views

Neutron view

Predefined user roles

network-admin

Parameters

centralized-vxlan: Specifies the VXLAN network with a centralized IP gateway.

distributed-vxlan: Specifies the VXLAN network with distributed IP gateways.

vlan: Specifies the VLAN network.

Examples

# Specify the network type as VXLAN network with a centralized IP gateway.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron] network-type centralized-vxlan

neutron

Use neutron to enable Neutron and enter Neutron view.

Use undo neutron to disable Neutron and delete all configurations in Neutron view.

Syntax

neutron

undo neutron

Default

Neutron is disabled.

Views

System view

Predefined user roles

network-admin

Examples

# Enable Neutron and enter Neutron view.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron]

proxy-arp enable

Use proxy-arp enable to enable local proxy ARP for VSI interfaces.

Use undo proxy-arp enable to restore the default.

Syntax

proxy-arp enable

undo proxy-arp enable

Default

Local proxy ARP is disabled for VSI interfaces. The device uses ARP flood suppression entries to answer ARP requests for MAC addresses of VMs on a different site from the requesting VMs.

Views

Neutron view

Predefined user roles

network-admin

Usage guidelines

Use this command only on leaf nodes on a VXLAN network with distributed IP gateways.

This feature enables the device to use the MAC address of VSI interfaces to answer ARP requests for MAC addresses of VMs on a different site from the requesting VMs. To configure the MAC address of VSI interfaces, use the vsi-mac command.

This command takes effect on VSI interfaces that are created after this command is executed. It does not take effect on existing VSI interfaces.

Examples

# Enable local ARP proxy for VSI interfaces.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron] proxy-arp enable

rabbit durable-queue enable

Use rabbit durable-queue enable to enable creation of RabbitMQ durable queues.

Use undo rabbit durable-queue enable to disable creation of RabbitMQ durable queues.

Syntax

rabbit durable-queue enable

undo rabbit durable-queue enable

Default

Creation of RabbitMQ durable queues is disabled. RabbitMQ non-durable queues are created and stored in the memory of RabbitMQ servers.

Views

Neutron view

Predefined user roles

network-admin

Usage guidelines

In a Neutron network, the device communicates with the Neutron server through RabbitMQ to obtain the configuration for deploying the overlay network. You must configure RabbitMQ server-related settings on the device and make sure the settings are the same as those on the Neutron server. If the durable attribute of RabbitMQ queues is set on the Neutron server, you must enable creation of RabbitMQ durable queues on the device so that RabbitMQ queues can be correctly created. The created RabbitMQ durable queues are stored in the disk of the RabbitMQ servers.

Examples

# Enable creation of RabbitMQ durable queues.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron] rabbit durable-queue enable

rabbit host

Use rabbit host to specify the IPv4 address, MPLS L3VPN instance, and port number of a RabbitMQ server.

Use undo rabbit host to restore the default.

Syntax

rabbit host ip ipv4-address [ port port-number ] [ vpn-instance vpn-instance-name ]

undo rabbit host ip ipv4-address [ vpn-instance vpn-instance-name ]

Default

No IPv4 address or MPLS L3VPN instance is specified for a RabbitMQ server, and the port number of a RabbitMQ server is 5672.

Views

Neutron view

Predefined user roles

network-admin

Parameters

ip ipv4-address: Specifies the IPv4 address of a RabbitMQ server.

port port-number: Specifies the port number for the device to communicate with a RabbitMQ server. The value range for the port-number argument is 1 to 65535.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If a RabbitMQ server is on the public network, do not specify this option.

Usage guidelines

The device communicates with the Neutron server through RabbitMQ servers.

Before you configure this command, make sure the controller where the Neutron server resides has been installed with RabbitMQ components.

If the device connects to a RabbitMQ server cluster, you can repeat this command to specify the IPv4 addresses of multiple RabbitMQ servers in the cluster.

You can specify the IPv4 address for a maximum of 32 RabbitMQ servers.

Examples

# Specify 10.11.113.143 as the IPv4 address of a RabbitMQ server.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron] rabbit host ip 10.11.113.143

rabbit password

Use rabbit password to configure the password for the device to establish connections with RabbitMQ servers.

Use undo rabbit password to restore the default.

Syntax

rabbit password { cipher | plain } string

undo rabbit password

Default

The device uses the plaintext password guest to establish connections with RabbitMQ servers.

Views

Neutron view

Predefined user roles

network-admin

Parameters

cipher: Specifies a password in encrypted form.

simple: Specifies a password in plaintext form. For security purposes, the password specified in plaintext form will be stored in encrypted form.

string: Specifies the password. Its plaintext form is a case-sensitive string of 4 to 64 characters. Its encrypted form is a case-sensitive string of 36 to 256 characters.

Usage guidelines

If you configure this command multiple times, the most recent configuration takes effect.

Examples

# Configure the device to use the plaintext password aaaa to establish connections with RabbitMQ servers.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron] rabbit password plain aaaa

rabbit source-ip

Use rabbit source-ip to specify the source IPv4 address for the device to communicate with RabbitMQ servers.

Use undo rabbit source-ip to restore the default.

Syntax

rabbit source-ip ipv4-address [ vpn-instance vpn-instance-name ]

Default

No source IPv4 address is specified for the device to communicate with RabbitMQ servers. The device automatically selects the source IPv4 address through the routing protocol to communicate with RabbitMQ servers.

Views

Neutron view

Predefined user roles

network-admin

Parameters

ipv4-address: Specifies the source IPv4 address with which the device communicates with RabbitMQ servers.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If the specified source IPv4 address is on the public network, do not specify this option.

Usage guidelines

Use this command if multiple equal-cost routes exist between the device and RabbitMQ servers. For example, assume that two equal-cost routes exist, and the outgoing interface in one route is a logical interface and that in the other route is a physical interface. If the device automatically selects the physical interface, communications with RabbitMQ servers might be interrupted and Neutron services will be further affected when the physical interface goes down. To avoid this problem, specify the IPv4 address of the logical interface as the source IPv4 address.

Examples

# Specify 1.1.1.1 as the source IPv4 address for the device to communicate with RabbitMQ servers.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron] rabbit source-ip 1.1.1.1

rabbit user

Use rabbit user to configure the username for the device to establish connections with RabbitMQ servers.

Use undo rabbit user to restore the default.

Syntax

rabbit user username

undo rabbit user

Default

The device uses username guest to establish connections with RabbitMQ servers.

Views

Neutron view

Predefined user roles

network-admin

Parameters

username: Specifies the username for the device to establish connections with RabbitMQ servers, a case-sensitive string of 1 to 63 characters.

Usage guidelines

If you configure this command multiple times, the most recent configuration takes effect.

Examples

# Configure the device to use username aaa to establish connections with RabbitMQ servers.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron] rabbit user aaa

rabbit virtual-host

Use rabbit virtual-host to specify a virtual host on a RabbitMQ server to provide services for the device.

Use undo rabbit virtual-host to restore the default.

Syntax

rabbit virtual-host hostname

undo rabbit virtual-host

Default

The virtual host with the name / provides RabbitMQ services for the device.

Views

Neutron view

Predefined user roles

network-admin

Parameters

hostname: Specifies the name of a virtual host on a RabbitMQ server. The hostname is a case-sensitive string of 1 to 63 characters.

Usage guidelines

Multiple virtual hosts might exist on a RabbitMQ server. Each virtual host can independently provide RabbitMQ services for the device. For the device to correctly communicate with the Neutron server, specify the same virtual host with the Neutron server.

Examples

# Specify the virtual host with the name aaa to provide RabbitMQ services for the device.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron] rabbit virtual-host aaa

restful user

Use restful user to configure the username and password for the device to deploy configurations through a RESTful API.

Use undo restful user to restore the default.

Syntax

restful user username password { plain | cipher } string

undo restful user

Default

No username and password is specified for the device to deploy configurations through a RESTful API.

Views

Neutron view

Predefined user roles

network-admin

Parameters

username: Specifies the username for the device to deploy configurations through a RESTful AP. The username is a case-sensitive string of 1 to 63 characters.

cipher: Specifies a password in encrypted form.

simple: Specifies a password in plaintext form. For security purposes, the password specified in plaintext form will be stored in encrypted form.

string: Specifies the password. Its plaintext form is a case-sensitive string of 3 to 64 characters. Its encrypted form is a case-sensitive string of 36 to 256 characters.

Usage guidelines

You must specify an existing pair of username and password.

If you configure this command multiple times, the most recent configuration takes effect.

Examples

# Configure the device to use username aaa and plaintext password aaaa to deploy configurations through a RESTful API.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron] restful user aaa password plain aaaa

vcf-fabric role

Use vcf-fabric role to specify the role of the device.

Use undo vcf-fabric role to restore the default.

Syntax

vcf-fabric role { access | leaf | spine }

undo vcf-fabric role

Default

The device is a leaf node.

Views

Neutron view

Predefined user roles

network-admin

Parameters

access: Specifies the access node.

leaf: Specifies the leaf node.

spine: Specifies the spine node.

Usage guidelines

If you change the role of the device, the new role takes effect after the device restarts.

Examples

# Specify the device as a spine node.

<Sysname> system-view

[Sysname] vcf-fabric role spine

vcf-fabric spine-role master

Use vcf-fabric spine-role master to specify the device as a master spine node.

Use undo vcf-fabric spine-role master to restore the default.

Syntax

vcf-fabric spine-role master

undo vcf-fabric spine-role

Default

The device is not a master spine node.

Views

System view

Predefined user roles

network-admin

Usage guidelines

You must execute this command on a spine node.

When multiple spines nodes exist in the VCF fabric, you must specify a device as the master spine node to collect the topology for the entire VCF fabric.

Examples

# Specify the device as a master spine.

<Sysname> system-view

[Sysname] vcf-fabric spine-role master

Related commands

vcf-fabric role

vcf-fabric topology enable

Use vcf-fabric topology enable to enable VCF fabric topology discovery.

Use undo vcf-fabric topology enable to disable VCF fabric topology discovery.

Syntax

vcf-fabric topology enable

undo vcf-fabric topology enable

Default

VCF fabric topology discovery is disabled.

Views

System view

Predefined user roles

network-admin

Examples

# Enable VCF fabric topology discovery.

<Sysname> system-view

[Sysname] vcf-fabric topology enable

vcf-fabric underlay autoconfigure

Use vcf-fabric underlay autoconfigure to specify the template file for automated underlay network deployment.

Use undo vcf-fabric underlay autoconfigure to restore the default.

Syntax

vcf-fabric underlay autoconfigure template

undo vcf-fabric underlay autoconfigure

Default

No template file is specified for automated underlay network deployment.

Views

System view

Predefined user roles

network-admin

Parameters

template: Specifies a template file by its name, a case-insensitive string of 1 to 127 characters. A template file is a file ending with the .template file extension.

Usage guidelines

After this command is executed, the device uses the specified template file to deploy the underlay network.

Examples

# Specify template file vxlan_leaf.template for automated underlay network deployment.

<Sysname> system-view

[Sysname] vcf-fabric underlay autoconfigure vxlan_leaf.template

vcf-fabric underlay pause

Use vcf-fabric underlay pause to pause automated underlay network deployment.

Use undo vcf-fabric underlay pause to continue automated underlay network deployment.

Syntax

vcf-fabric underlay pause

undo vcf-fabric underlay pause

Default

Automated underlay network deployment is not paused.

Views

System view

Predefined user roles

network-admin

Usage guidelines

You can use this command to pause automated underlay network deployment if the device is in the process of automated underlay network deployment.

Examples

# Pause automated underlay network deployment.

<Sysname> system-view

[Sysname] vcf-fabric underlay pause

vpn-target export-extcommunity

Use vpn-target export-extcommunity to configure export route targets for a tenant VPN instance.

Use undo vpn-target export-extcommunity to restore the default.

Syntax

vpn-target target export-extcommunity

undo vpn-target target export-extcommunity

Default

No export route targets are configured for a tenant VPN instance.

Views

Neutron view

Predefined user roles

network-admin

Parameters

target: Specifies a route target, a string of 3 to 21 characters in one of the following formats:

·     16-bit AS number:32-bit user-defined number. For example, 101:3.

·     32-bit IP address:16-bit user-defined number. For example, 192.168.122.15:1.

·     32-bit AS number:16-bit user-defined number, where the AS number must not be less than 65536. For example, 65536:1.

Usage guidelines

The border node connects to the external network through an interface which belongs to the global VPN instance. For the traffic from the external network to reach a tenant network, the border node needs to add the routes of the tenant VPN instance into the routing table of the global VPN instance. Use this command to configure export route targets of the tenant VPN instance as import route targets of the global VPN instance. This setting enables the global VPN instance to import routes of the tenant VPN instance.

Examples

# Configure export route targets for a tenant VPN instance.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron] vpn-target 1:1 export-extcommunity

vpn-target import-extcommunity

Use vpn-target import-extcommunity to configure import route targets for a tenant VPN instance.

Use undo vpn-target import-extcommunity to restore the default.

Syntax

vpn-target target import-extcommunity

undo vpn-target target import-extcommunity

Default

No import route targets are configured for a tenant VPN instance.

Views

Neutron view

Predefined user roles

network-admin

Parameters

target: Specifies a route target, a string of 3 to 21 characters in one of the following formats:

·     16-bit AS number:32-bit user-defined number. For example, 101:3.

·     32-bit IP address:16-bit user-defined number. For example, 192.168.122.15:1.

·     32-bit AS number:16-bit user-defined number, where the AS number must not be less than 65536. For example, 65536:1.

Usage guidelines

Use this command only on leaf nodes on a VXLAN network with distributed IP gateways.

You do not need to execute this command if you have used the gateway ip or border enable command to create the default route to the external network.

In a data center, the border node connects to the external network through an interface which belongs to the global VPN instance. For tenant network data to reach the external network, use this command to configure import targets of the tenant VPN instance as export targets of the global VPN instance. This setting enables the tenant VPN instance to import routes of the global VPN instance.

Examples

# Configure import route targets for a tenant VPN instance.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron] vpn-target 1:1 import-extcommunity

vsi-mac

Use vsi-mac to configure a MAC address for VSI interfaces.

Use undo vsi-mac to delete the MAC address for VSI interfaces.

Syntax

vsi-mac mac-address

undo vsi-mac

Default

No MAC address is specified for VSI interfaces.

Views

Neutron view

Predefined user roles

network-admin

Parameters

mac-address: Specifies a MAC address in the H-H-H format.

Usage guidelines

Use this command only on leaf nodes on a VXLAN network with distributed IP gateways.

This command assigns the MAC address to all VSI interfaces newly created by automated overlay network deployment on the device.

This command takes effect only on VSI interfaces newly created after this command is executed.

Examples

# Configure the MAC address of all VSI interfaces as 1-1-1.

<Sysname> system-view

[Sysname] neutron

[Sysname-neutron] vsi-mac 1-1-1