11-Network Management and Monitoring Command Reference

HomeSupportResource CenterH3C S5560S-EI&S5560S-SI&S5500V3-SI Switch Series Command References-R612x-6W10211-Network Management and Monitoring Command Reference
04-PoE commands
Title Size Download
04-PoE commands 97.74 KB

PoE commands

apply poe-profile

Use apply poe-profile to apply a PoE profile to a power interface (PI).

Use undo apply poe-profile to restore the default.

Syntax

apply poe-profile { index index | name profile-name }

undo apply poe-profile { index index | name profile-name }

Default

No PoE profile is applied to PIs.

Views

PI view

Predefined user roles

network-admin

Parameters

index index: Specifies a PoE profile by its index number in the range of 1 to 100.

name profile-name: Specifies a PoE profile by its name, a case-sensitive string of 1 to 15 characters.

Examples

# Apply the PoE profile named forIPphone to GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] apply poe-profile name forIPphone

Related commands

apply poe-profile interface

display poe-profile

apply poe-profile interface

Use apply poe-profile interface to apply a PoE profile to PIs.

Use undo apply poe-profile interface to remove the PoE profile application from PIs.

Syntax

apply poe-profile { index index | name profile-name } interface interface-range

undo apply poe-profile { index index | name profile-name } interface interface-range

Default

No PoE profile is applied to a PI.

Views

System view

Predefined user roles

network-admin

Parameters

index index: Specifies a PoE profile by its index number in the range of 1 to 100.

name profile-name: Specifies a PoE profile by its name, a case-sensitive string of 1 to 15 characters.

interface-range: Specifies a range of Ethernet interfaces in the form of interface-type interface-number [ to interface-type interface-number ], where interface-type interface-number represents the interface type and interface number. The start interface number must be smaller than the end interface number. If an interface in the specified range does not support PoE, it is ignored when the PoE profile is applied.

Examples

# Apply the PoE profile named forIPphone to GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] apply poe-profile name forIPphone interface gigabitethernet 1/0/1

# Apply the PoE profile with index number 1 to PIs GigabitEthernet 1/0/2 to GigabitEthernet 1/0/6.

<Sysname> system-view

[Sysname] apply poe-profile index 1 interface gigabitethernet 1/0/2 to gigabitethernet 1/0/6

Related commands

apply poe-profile

display poe-profile interface

display poe device

Use display poe device to display general PSE information.

Syntax

display poe device [ slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, the command displays general PSE information about all PSEs in the IRF fabric.

Examples

# Display general PSE information.

<Sysname> display poe device

Slot  1:

 PSE ID    Slot No.  SSlot No. PortNum   MaxPower(W)    State   Model

 4          1          0           48         600.0           Off      LSPPSE48A

Table 1 Command output

Field

Description

PSE ID

ID of the PSE.

Slot No.

Slot number of the PSE.

SSlot No.

Sub-slot number of the PSE.

PortNum

Number of PIs on the PSE.

MaxPower(W)

Maximum power of the PSE.

State

PSE status:

·         On—The PSE is supplying power.

·         Off—The PSE is not supplying power.

·         Faulty—The PSE has failed.

Model

PSE model.

display poe interface

Use display poe interface to display power supplying information for PIs.

Syntax

display poe interface [ interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays power supplying information for all PIs.

Examples

# Display power supplying information for GigabitEthernet 1/0/1.

<Sysname> display poe interface gigabitethernet 1/0/1

 

 PoE Status                         : Enabled

 Power Priority                    : Critical

 Oper                                : On

 IEEE Class                         : 1

 Detection Status                  : Delivering power

 Power Mode                         : Signal

 Current Power                      : 11592    mW

 Average Power                      : 11610    mW

 Peak Power                          : 11684    mW

 Max Power                           : 15400    mW

 Electric Current                   : 244      mA

 Voltage                              : 51.7     V

 PD Description                      : IP Phone For Room 101

Table 2 Command output

Field

Description

PoE Status

PoE status:

·         Enabled.

·         Disabled.

Power Priority

Power supply priority of the PI:

·         Critical (highest).

·         High.

·         Low.

Oper

Operating status of a PI:

·         Off—PoE is disabled.

·         On—Power is being supplied to the PI correctly.

·         Power-lack—Remaining guaranteed power is insufficient for a critical PI.

·         Power-deny—The PSE refuses to supply power. The power required by the PD is higher than the configured power.

·         Power-itself—The PD is using another power supply.

·         Power-limit—The PSE is supplying power to the PD based on the configured power though the PD requires more power than the configured power.

IEEE Class

PD power class: 0, 1, 2, 3, or 4.

If the PSE does not support PD classification, this field displays a hyphen (-).

Detection Status

Power detection status of a PI:

·         Disabled—The PoE function is disabled.

·         Searching—The PI is searching for the PD.

·         Delivering power—The PI is supplying power to the PD.

·         Fault—A fault occurred during the test.

·         Test—The PI is undergoing a test.

·         Other fault—A fault has caused the PSE to enter the idle status.

·         PD disconnected—The PD is disconnected.

Power Mode

Power transmission mode of a PI:

·         Signal—Power is being supplied over signal cables.

·         Spare—Power is being supplied over spare cables.

Current Power

Current power of a PI, including PD consumption power and transmission loss.

Average Power

Average power of a PI.

Peak Power

Peak power of a PI.

Max Power

Maximum power of a PI.

Electric Current

Current of a PI.

Voltage

Voltage of a PI.

PD Description

Type and location description for the PD connected to the PI.

# Display power supplying information for all PIs.

<Sysname> display poe interface

 Interface    PoE       Priority  CurPower  Oper    IEEE  Detection

                                     (W)                  Class Status

 GE1/0/1      Disabled  Low       0.0       Off       0     Disabled

 GE1/0/2      Enabled   Low       0.0       Off       0     Searching

 GE1/0/3      Disabled  Low       0.0       Off       0     Disabled

 GE1/0/4      Disabled  Low       0.0       Off       0     Disabled

 GE1/0/5      Disabled  Low       0.0       Off       0     Disabled

 GE1/0/6      Disabled  Low       0.0       Off       0     Disabled

 GE1/0/7      Disabled  Low       0.0       Off       0     Disabled

 GE1/0/8      Disabled  Low       0.0       Off       0     Disabled

 GE1/0/9      Disabled  Low       0.0       Off       0     Disabled

 GE1/0/10     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/11     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/12     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/13     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/14     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/15     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/16     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/17     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/18     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/19     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/20     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/21     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/22     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/23     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/24     Disabled  Low       0.0       Off       0     Disabled

   ---  On State Ports: 0; Used: 0.0(W); Remaining: 370.0(W)  ---

Table 3 Command output

Field

Description

Interface

Interface name of a PI.

PoE

PoE status:

·         Enabled.

·         Disabled.

Priority

Power priority of a PI:

·         Critical (highest).

·         High.

·         Low.

CurPower

Current power of a PI.

Oper

Operating status of a PI:

·         Off—PoE is disabled.

·         On—Power is being supplied to the PI correctly.

·         Power-lack—Remaining guaranteed power is insufficient for a critical PI.

·         Power-deny—The PSE refuses to supply power. The power required by the PD is higher than the configured power.

·         Power-itself—The PD is using another power supply.

·         Power-limit—The PSE is supplying power to the PD based on the configured power though the PD requires more power than the configured power.

IEEE Class

PD power class: 0, 1, 2, 3, or 4.

If the PSE does not support PD classification, this field displays a hyphen (-).

Detection Status

Power detection status of a PI:

·         Disabled—PoE function is disabled.

·         Searching—The PI is searching for the PD.

·         Delivering Power—The PI is supplying power for the PD.

·         Fault—A fault occurred during the test.

·         Test—The PI is undergoing a test.

·         Other fault—A fault has caused the PSE to enter the idle status.

·         PD disconnected—The PD is disconnected.

On State Ports

Number of PIs that are supplying power.

Used

Power consumed by the current PI.

Remaining

Total remaining power of the system.

display poe interface power

Use display poe interface power to display power information for PIs.

Syntax

display poe interface power [ interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays power information for all PIs.

Examples

# Display power information for GigabitEthernet 1/0/1.

<Sysname> display poe interface power gigabitethernet 1/0/1

Interface    Current   Peak      Max       PD Description

               (W)       (W)       (W)

 GE1/0/1        15.0      15.3      30.0      Access Point on Room 509 for Peter

# Display power information for all PIs.

<Sysname> display poe interface power

 Interface    Current   Peak      Max       PD Description

              (W)       (W)       (W)

 GE1/0/1      0.0       0.0       30.0

 GE1/0/2      0.0       0.0       30.0

 GE1/0/3      0.0       0.0       30.0

 GE1/0/4      0.0       0.0       30.0

 GE1/0/5      0.0       0.0       30.0

 GE1/0/6      0.0       0.0       30.0

 GE1/0/7      0.0       0.0       30.0

 GE1/0/8      0.0       0.0       30.0

 GE1/0/9      0.0       0.0       30.0

 GE1/0/10     0.0       0.0       30.0

 GE1/0/11     0.0       0.0       30.0

 GE1/0/12     0.0       0.0       30.0

 GE1/0/13     0.0       0.0       30.0

 GE1/0/14     0.0       0.0       30.0

 GE1/0/15     0.0       0.0       30.0

 GE1/0/16     0.0       0.0       30.0

 GE1/0/17     0.0       0.0       30.0

 GE1/0/18     0.0       0.0       30.0

 GE1/0/19     0.0       0.0       30.0

 GE1/0/20     0.0       0.0       30.0

 GE1/0/21     0.0       0.0       30.0

 GE1/0/22     0.0       0.0       30.0

 GE1/0/23     0.0       0.0       30.0

 GE1/0/24     0.0       0.0       30.0

   ---  On State Ports: 0; Used: 0.0(W); Remaining: 370.0(W)  ---

Table 4 Command output

Field

Description

Interface

Interface name of a PI.

CurPower

Current power of a PI.

PeakPower

Peak power of a PI.

MaxPower

Maximum power of a PI.

PD Description

Type and location description for the PD connected to a PI.

Ports On

Number of PIs that are supplying power.

Used

Power consumed by all PIs.

Remaining

Total remaining power of the system.

display poe pse

Use display poe pse to display detailed PSE information.

Syntax

display poe pse [ pse-id ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

pse-id: Specifies a PSE by its ID. If you do not specify a PSE, this command displays detailed PSE information about all PSEs.

Examples

# Display detailed PSE information.

<Sysname> display poe pse

 PSE ID                            : 4

 Slot No.                          : 1

 SSlot No.                         : 0

 PSE Model                         : LSPPSE48A

 PSE Status                        : Enabled

 Power Priority                   : Low

 Current Power                    : 0.0      W

 Average Power                    : 0.0      W

 Peak Power                        : 0.0      W

 Max Power                         : 600.0    W

 Remaining Guaranteed Power     : 600.0    W

 PSE CPLD Version                 : -

 PSE Software Version             : 172

 PSE Hardware Version             : 0

 Legacy PD Detection              : Disabled

 Power Utilization Threshold    : 80

 PD Power Policy                  : Priority

 PD Disconnect-Detection Mode   : DC

Table 5 Command output

Field

Description

PSE ID

ID of the PSE.

SSlot No.

Sublsot number of the PSE.

PSE Status

PoE status of the PSE:

·         Enabled.

·         Disabled.

Power Priority

Power priority of the PSE.

Current Power

Current power of the PSE.

Average Power

Average power of the PSE.

Peak Power

Peak power of the PSE.

Max Power

Maximum power of the PSE.

Remaining Guaranteed Power

Remaining guaranteed power of the PSE = Maximum guaranteed power of the PSE – Total maximum power of all critical PIs of the PSE.

PSE CPLD Version

PSE CPLD version number.

PSE Software Version

PSE software version number.

PSE Hardware Version

PSE hardware version number.

Legacy PD Detection

Nonstandard PD detection status:

·         Enabled.

·         Disabled.

Power Utilization Threshold

PSE power alarm threshold.

PD Power Policy

PD power management policy mode.

PD Disconnect-Detection Mode

PD disconnection detection mode.

display poe pse interface

Use display poe pse interface to display the PoE status of all PIs on a PSE.

Syntax

display poe pse pse-id interface

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

pse pse-id: Specifies a PSE ID. To display PSE ID and slot mappings, use the display poe device command.

Examples

# Display the status of all PIs on PSE 4.

<Sysname> display poe pse 4 interface

 Interface    PoE       Priority  CurPower  Oper    IEEE  Detection

                                     (W)                  Class Status

 GE1/0/1      Disabled  Low       0.0       Off       0     Disabled

 GE1/0/2      Enabled   Low       0.0       Off       0     Searching

 GE1/0/3      Disabled  Low       0.0       Off       0     Disabled

 GE1/0/4      Disabled  Low       0.0       Off       0     Disabled

 GE1/0/5      Disabled  Low       0.0       Off       0     Disabled

 GE1/0/6      Disabled  Low       0.0       Off       0     Disabled

 GE1/0/7      Disabled  Low       0.0       Off       0     Disabled

 GE1/0/8      Disabled  Low       0.0       Off       0     Disabled

 GE1/0/9      Disabled  Low       0.0       Off       0     Disabled

 GE1/0/10     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/11     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/12     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/13     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/14     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/15     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/16     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/17     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/18     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/19     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/20     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/21     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/22     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/23     Disabled  Low       0.0       Off       0     Disabled

 GE1/0/24     Disabled  Low       0.0       Off       0     Disabled

   ---  On State Ports: 0; Used: 0.0(W); Remaining: 370.0(W)  ---

Table 6 Command output

Field

Description

Interface

Interface name of a PI.

PoE

PoE status of a PI:

·         Enabled.

·         Disabled.

Priority

Priority of a PI:

·         Critical (highest).

·         High.

·         Low.

CurPower

Current power of a PI.

Oper

Operating status of a PI:

·         Off—PoE is disabled.

·         On—Power is being supplied to the PI correctly.

·         Power-lack—Remaining guaranteed power is insufficient for a critical PI.

·         Power-deny—The PSE refuses to supply power. The power required by the PD is higher than the configured power.

·         Power-itself—The PD is using another power supply.

·         Power-limit—The PSE is supplying power to the PD based on the configured power though the PD requires more power than the configured power.

IEEE Class

PD power class: 0, 1, 2, 3, or 4.

If the PSE does not support PD classification, this field displays a hyphen (-).

Detection Status

Power detection status of a PI:

·         Disabled—PoE function is disabled.

·         Searching—The PI is searching for the PD.

·         Delivering Power—The PI is supplying power to the PD.

·         Fault—A fault occurred during the test.

·         Test—The PI is undergoing a test.

·         Other Fault—A fault has caused the PSE to enter the idle status.

·         PD Disconnected—The PD is disconnected.

On State Ports

Number of PIs that are supplying power.

Used

Power consumed by PIs on the PSE.

Remaining

Remaining power on the PSE.

display poe pse interface power

Use display poe pse interface power to display power information for PIs on a PSE.

Syntax

display poe pse pse-id interface power

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

pse pse-id: Specifies a PSE by its ID. To display PSE ID and slot mappings, use the display poe device command.

Examples

# Display power information for PIs on PSE 4.

<Sysname> display poe pse 4 interface power

 Interface    Current   Peak      Max       PD Description

              (W)       (W)       (W)

 GE1/0/1      0.0       0.0       30.0

 GE1/0/2      0.0       0.0       30.0

 GE1/0/3      0.0       0.0       30.0

 GE1/0/4      0.0       0.0       30.0

 GE1/0/5      0.0       0.0       30.0

 GE1/0/6      0.0       0.0       30.0

 GE1/0/7      0.0       0.0       30.0

 GE1/0/8      0.0       0.0       30.0

 GE1/0/9      0.0       0.0       30.0

 GE1/0/10     0.0       0.0       30.0

 GE1/0/11     0.0       0.0       30.0

 GE1/0/12     0.0       0.0       30.0

 GE1/0/13     0.0       0.0       30.0

 GE1/0/14     0.0       0.0       30.0

 GE1/0/15     0.0       0.0       30.0

 GE1/0/16     0.0       0.0       30.0

 GE1/0/17     0.0       0.0       30.0

 GE1/0/18     0.0       0.0       30.0

 GE1/0/19     0.0       0.0       30.0

 GE1/0/20     0.0       0.0       30.0

 GE1/0/21     0.0       0.0       30.0

 GE1/0/22     0.0       0.0       30.0

 GE1/0/23     0.0       0.0       30.0

 GE1/0/24     0.0       0.0       30.0

   ---  On State Ports: 0; Used: 0.0(W); Remaining: 370.0(W)  ---

Table 7 Command output

Field

Description

Interface

Interface name of a PI.

Current

Current power of a PI.

Peak

Peak power of a PI.

Max

Maximum power of a PI.

PD Description

Type and location description for the PD connected with a PI.

Ports On

Number of PIs that are supplying power.

Used

Power consumed by all PIs.

Remaining

Remaining power on the PSE.

display poe-profile

Use display poe-profile to display information about the PoE profile.

Syntax

display poe-profile [ index index | name profile-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

index index: Specifies a PoE profile by its index number in the range of 1 to 100.

name profile-name: Specifies a PoE profile by its name, a case-sensitive string of 1 to 15 characters.

Usage guidelines

If you do not specify a profile, the command displays information about all PoE profiles.

Examples

# Display information about all PoE profiles.

<Sysname> display poe-profile

 PoE Profile     Index   ApplyNum  Interfaces     Configuration

 forIPphone      1        4           GE1/0/1        poe enable

                                        GE1/0/2           poe priority critical

                                        GE1/0/3

                                        GE1/0/4

 forAP            2        2           GE1/0/5         poe enable

                                        GE1/0/6         poe max-power 14000

   ---  Total PoE profiles: 2, total ports: 6  ---

# Display information about the PoE profile with index number 1.

<Sysname> display poe-profile index 1

 PoE Profile     Index   ApplyNum  Interfaces   Configuration

 forIPphone      1        6          GE1/0/1         poe enable

                                       GE1/0/2         poe priority critical

                                       GE1/0/3

                                       GE1/0/4

                                       GE1/0/5

                                       GE1/0/6

   ---  Total ports: 6  ---

Table 8 Command output

Field

Description

PoE Profile

Name of the PoE profile.

Index

Index number of the PoE profile.

ApplyNum

Number of PIs to which the PoE profile is applied.

Interfaces

Interface name of the PI to which the PoE configuration is applied.

Configuration

Configurations of the PoE profile.

Total PoE profiles

Number of PoE profiles.

Total ports

Number of PIs to which all PoE profiles are applied.

display poe-profile interface

Use display poe-profile interface to display information about the PoE profile on a PI.

Syntax

display poe-profile interface interface-type interface-number

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number.

Examples

# Display information about the PoE profile on GigabitEthernet 1/0/1.

<Sysname> display poe-profile interface gigabitethernet 1/0/1

 PoEProfile     Index   ApplyNum  Interface   Effective configuration

 forIPphone      1        6          GE1/0/1       poe enable

                                                    poe priority critical

The Effective configuration field displays the configurations that have taken effect. For the descriptions of other fields, see Table 8.

poe detection-mode

Use poe detection-mode to configure a PD detection mode.

Use undo poe detection-mode to restore the default.

 

 

NOTE:

This command is supported only in Release 6127 and later.

 

Syntax

poe detection-mode { none | simple | strict }

undo poe detection-mode

Default

The strict PD detection mode applies.

Views

PI view

Predefined user roles

network-admin

Parameters

none: Enables the device to supply power to PDs that are correctly connected to the device without causing short circuit.

simple: Enables the device to supply power to PDs that comply with basic requirements of 802.3af or 802.3at.

strict: Enables the device to supply power to PDs that comply with all requirements of 802.3af or 802.3at.

Usage guidelines

CAUTION

CAUTION:

A non-PD device might be damaged when power is supplied to it. To avoid device damage, do not specify the none keyword when the PI connects to a non-PD device.

 

To configure the detection mode for nonstandard PDs, first execute the poe legacy enable command to enable detection for nonstandard PDs.

Examples

# Configure the simple detection mode for GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] poe detection-mode simple

Related commands

poe legacy enable

poe enable

Use poe enable to enable PoE on a PI.

Use undo poe enable to disable PoE on a PI.

Syntax

poe enable

undo poe enable

Default

PoE is disabled on a PI.

Views

PI view

PoE profile view

Predefined user roles

network-admin

Usage guidelines

If a PoE profile has been applied to a PI, remove the application before configuring the PI in PoE profile view.

If a PI has been configured, remove the configuration before configuring the PI in PI view.

Examples

# Enable PoE on a PI in PI view.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] poe enable

# Enable PoE on a PI in PoE profile view.

<Sysname> system-view

[Sysname] poe-profile abc

[Sysname-poe-profile-abc-1] poe enable

Related commands

display poe interface

poe-profile

poe legacy enable

Use poe legacy enable to enable the PSE to detect nonstandard PDs.

Use undo poe legacy enable to disable the PSE from detecting nonstandard PDs.

Syntax

poe legacy enable pse pse-id

undo poe legacy enable pse pse-id

Default

Nonstandard PD detection is disabled.

Views

System view

Predefined user roles

network-admin

Parameters

pse pse-id: Specifies a PSE by its ID.

Examples

# Enable PSE 4 to detect nonstandard PDs.

<Sysname> system-view

[Sysname] poe legacy enable pse 4

Related commands

display poe pse

poe max-power

Use poe max-power to set the maximum PI power.

Use undo poe max-power to restore the default.

Syntax

poe max-power max-power

undo poe max-power

Default

The maximum PI power is 30000 W.

Views

PI view

PoE profile view

Predefined user roles

network-admin

Parameters

max-power: Sets the maximum PI power in milliwatts. The value range is 1000 to 30000.

Examples

# Set the maximum PI power to 12000 milliwatts in PI view.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] poe max-power 12000

# Set the maximum PI power to 12000 milliwatts in PoE profile view.

<Sysname> system-view

[Sysname] poe-profile abc

[Sysname-poe-profile-abc-1] poe max-power 12000

poe pd-description

Use poe pd-description to configure a description for the PD that connects to a PI.

Use undo poe pd-description to restore the default.

Syntax

poe pd-description text

undo poe pd-description

Default

No description is configured for the PD that connects to a PI.

Views

PI view

Predefined user roles

network-admin

Parameters

text: Configures a description for the PD connected to the PI, a case-sensitive string of 1 to 80 characters.

Examples

# Configure the description for the PD as IP Phone for Room 101.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] poe pd-description IP Phone For Room 101

poe pd-policy priority

Use poe pd-policy priority to enable PI power management.

Use undo poe pd-policy priority to restore the default.

Syntax

poe pd-policy priority

undo poe pd-policy priority

Default

PI power management is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

If PI power management is disabled, the PSE does not supply power to new PDs when PSE power overload occurs.

If PI power management is enabled, when a PSE is overloaded, the PSE allocates power to PDs based on the priority of their PIs.

Examples

# Enable PI power management.

<Sysname> system-view

[Sysname] poe pd-policy priority

Related commands

poe priority

poe priority

Use poe priority to set the power supply priority for a PI.

Use undo poe priority to restore the default.

Syntax

poe priority { critical | high | low }

undo poe priority

Default

The power supply priority of a PI is low.

Views

PI view

PoE profile view

Predefined user roles

network-admin

Parameters

critical: Sets the power supply priority to critical. The PI with critical power priority operates in guaranteed mode. Power is first supplied to the PD connected to the critical PI.

high: Sets the power supply priority to high.

low: Sets the power supply priority to low.

Usage guidelines

When the PoE power is insufficient, power is first supplied to PIs with higher priority.

For PIs with same power supply priority, the PI with the smallest ID is allocated with power first.

If a PoE profile has been applied to a PI, remove the application before configuring the PI in PoE profile view.

If a PI has been configured, remove the configuration before configuring the PI in PI view.

Examples

# Set the power supply priority of the PI to critical in PI view.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] poe priority critical

# Set the power supply priority of the PI to critical in PoE profile view.

<Sysname> system-view

[Sysname] poe-profile abc

[Sysname-poe-profile-abc-1] poe priority critical

[Sysname-poe-profile-abc-1] quit

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] apply poe-profile name abc

Related commands

poe pd-policy priority

poe reset enable

Use poe reset enable to enable PI power cycling upon a system warm reboot.

Use undo poe pse-policy priority to disable PI power cycling upon a system warm reboot.

Syntax

poe reset enable

undo poe reset enable

Default

PI power cycling upon a system warm reboot is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

During the system warm reboot process (upon execution of the reboot command), the PIs continue supplying power to the PDs but data connections between the PDs and the device are interrupted. After the system reboots, PDs might not re-initiate data connections with the device. Power cycling PIs upon a system warm reboot allows the PDs to re-establish data connections with the device.

Examples

# Enable PI power cycling upon a system warm reboot.

<Sysname> system-view

[Sysname] poe reset enable

poe update

Use poe update to upgrade the PSE firmware when the device is operating.

Syntax

poe update { full | refresh } filename [ pse pse-id ]

Views

System view

Predefined user roles

network-admin

Parameters

full: Upgrades the PSE firmware in full mode.

refresh: Upgrades the PSE firmware in refresh mode.

filename: Specifies the name of the upgrade file, a case-insensitive string of 1 to 64 characters. The specified file must be in the root directory of the file system of the device.

pse pse-id: Specifies a PSE by its ID. If you do not specify a PSE, all PSEs are upgraded.

Usage guidelines

You can upgrade the PSE firmware in service in either of the following modes:

·          Refresh mode—Updates the PSE firmware without deleting it. You can use the refresh mode in most cases.

·          Full mode—Deletes the current PSE firmware and reloads a new one. Use the full mode if the PSE firmware is damaged and you cannot execute any PoE commands.

Examples

# Upgrade the firmware of PSE 4 in service.

<Sysname> system-view

[Sysname] poe update refresh POE-168.bin pse 4

poe utilization-threshold

Use poe utilization-threshold to configure a power alarm threshold for the PSE.

Use undo poe utilization-threshold to restore the default power alarm threshold of the PSE.

Syntax

poe utilization-threshold value pse pse-id

undo poe utilization-threshold pse pse-id

Default

The power alarm threshold for the PSE is 80%.

Views

System view

Predefined user roles

network-admin

Parameters

value: Specifies alarm threshold as a percentage of 1 to 99.

pse pse-id: Specifies a PSE by its ID.

Usage guidelines

If PSE power usage crosses the threshold multiple times in succession, the system sends notification messages only for the first crossing. For more information, see "Configuring SNMP."

Examples

# Set the power alarm threshold of PSE 4 to 90%.

<Sysname> system-view

[Sysname] poe utilization-threshold 90 pse 4

poe-profile

Use poe-profile to create a PoE profile and enter its view, or enter the view of an existing PoE profile.

Use undo poe-profile to delete a PoE profile.

Syntax

poe-profile profile-name [ index ]

undo poe-profile { index index | name profile-name }

Default

No PoE profiles exist.

Views

System view

Predefined user roles

network-admin

Parameters

profile-name: Specifies a PoE profile name, a case-sensitive string of 1 to 15 characters. A PoE configuration file name begins with a letter and must not contain reserved keywords including undo, all, name, interface, user, poe, disable, max-power, mode, priority, or enable.

index: Specifies the index number of a PoE profile, in the range of 1 to 100.

Usage guidelines

To configure PIs in batches, use the PoE profile.

If you do not specify a profile index, the system automatically assigns an index (starting from 1) to the PoE profile.

If a PoE profile is applied, use the undo apply poe-profile command to remove the application before deleting the PoE profile.

Examples

# Create a PoE profile, name it abc, and specify the index number as 3.

<Sysname> system-view

[Sysname] poe-profile abc 3

[Sysname-poe-profile-abc-3]

# Create a PoE profile and name it def. Do not specify the index number.

<Sysname> system-view

[Sysname] poe-profile def

[Sysname-poe-profile-def-1]

Related commands

apply poe-profile

poe enable

poe max-power

poe priority