06-IP Multicast Command Reference

HomeSupportResource CenterH3C S5560S-EI&S5560S-SI&S5500V3-SI Switch Series Command References-R612x-6W10206-IP Multicast Command Reference
05-IGMP commands
Title Size Download
05-IGMP commands 157.67 KB

IGMP commands

display igmp group

Use display igmp group to display information about IGMP multicast groups (multicast groups that hosts have joined through IGMP).

Syntax

display igmp group [ group-address | interface interface-type interface-number ] [ static | verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

group-address: Specifies a multicast group by its IP address in the range of 224.0.1.0 to 239.255.255.255. If you do not specify a multicast group, this command displays information about all IGMP multicast groups.

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays information about IGMP multicast groups for all interfaces.

static: Specifies IGMP multicast groups that hosts have joined statically. If you do not specify this keyword, the command displays information about IGMP multicast groups that hosts have joined dynamically.

verbose: Displays detailed information.

Examples

# Display information about IGMP multicast groups that hosts have dynamically joined.

<Sysname> display igmp group

IGMP groups in total: 3

 Vlan-interface1(10.10.1.20):

  IGMP groups reported in total: 3

   Group address   Last reporter   Uptime      Expires

   225.1.1.1       10.10.1.10      00:02:04    00:01:15

   225.1.1.2       10.10.1.10      00:02:04    00:01:15

   225.1.1.3       10.10.1.10      00:02:04    00:01:15

Table 1 Command output

Field

Description

IGMP groups in total

Total number of IGMP multicast groups.

IGMP groups reported in total

Total number of IGMP multicast groups that hosts attached to the interface have joined dynamically.

Group address

Multicast group address.

Last reporter

Address of the last host that reported its membership to the multicast group.

Uptime

Length of time since the multicast group was reported.

Expire

Remaining lifetime for the multicast group. This field displays Off if the timer is disabled.

 

# Display detailed information about IGMP multicast group 232.1.1.1 that hosts have dynamically joined. In this example, the switch is configured with IGMPv3.

<Sysname> display igmp group 232.1.1.1 verbose

 Vlan-interface1(10.10.1.20):

  IGMP groups reported in total: 3

   Group: 232.1.1.1

     Uptime: 00:00:34

     Exclude expires: 00:04:16

     Mapping expires: 00:02:16

     Last reporter: 10.10.1.10

     Last-member-query-counter: 0

     Last-member-query-timer-expiry: Off

     Mapping last-member-query-counter: 0

     Mapping last-member-query-timer-expiry: Off

     Group mode: Exclude

     Version1-host-present-timer-expiry: Off

     Version2-host-present-timer-expiry: 00:02:11

     Mapping version1-host-present-timer-expiry: Off

     Source list (sources in total: 1):

       Source: 10.1.1.1

          Uptime: 00:00:03

          V3 expires: 00:04:16

          Mapping expires: 00:02:16

          Last-member-query-counter: 0

          Last-member-query-timer-expiry: Off

Table 2 Command output

Field

Description

IGMP groups reported in total

Total number of IGMP multicast groups that hosts attached to the interface have joined dynamically.

Group

Multicast group address.

Uptime

Length of time since the multicast group was reported.

Exclude expires

Remaining lifetime for the multicast group in Exclude mode. This field displays Off if the timer is disabled.

Mapping expires

Remaining time for the multicast group specified in IGMP SSM mappings.

This field is displayed only when the device is configured with IGMP SSM mappings.

Last reporter

Address of the last host that reported its membership to this multicast group.

Last-member-query-counter

Number of IGMP group-specific queries or IGMP source-and-group-specific queries sent for the multicast group.

Last-member-query-timer-expiry

Remaining time for the last member query timer for the multicast group. This field displays Off if the timer is disabled.

Mapping last-member-query-counter

Number of IGMP group-specific queries or IGMP source-and-group-specific queries sent for the multicast group specified in IGMP SSM mappings.

This field is displayed only when the device is configured with IGMP SSM mappings.

Mapping last-member-query-timer-expiry

Remaining time for the last member query timer of the multicast group specified in IGMP SSM mappings.

This field displays Off if the timer is disabled.

This field is displayed only when the device is configured with IGMP SSM mappings.

Group mode

Multicast source filtering mode:

·         IncludeInclude mode.

·         Exclude—Exclude mode.

For a device that runs IGMPv1 or IGMPv2:

·         If IGMP SSM mappings are not configured, this field displays Exclude.

·         If IGMP SSM mappings are configured, this field displays Include or Exclude depending on the SSM mappings and the multicast groups that the host joins.

Version1-host-present-timer-expiry

Remaining time for the IGMPv1 host present timer.

This field displays Off if the timer is disabled.

This field is displayed only when the device runs IGMPv2 or IGMPv3.

Version2-host-present-timer-expiry

Remaining time for the IGMPv2 host present timer.

This field displays Off if the timer is disabled.

This field is displayed only when the device runs IGMPv3.

Mapping version1-host-present-timer-expiry

Remaining time for the IGMPv1 host present timer when the device is configured with IGMP SSM mappings.

This field displays Off if the timer is disabled.

This field is displayed only when the device is configured with IGMP SSM mappings.

Source list (sources in total)

List of multicast sources and total number of multicast sources.

This field is displayed only when the device runs IGMPv3 or when the device is configured with IGMP SSM mappings.

Source

Multicast source address.

This field is displayed only when the device runs IGMPv3 or when the device is configured with IGMP SSM mappings.

Uptime

Length of time since the multicast source was reported.

This field is displayed only when the device runs IGMPv3 or when the device is configured with IGMP SSM mappings.

V3 expires

Remaining time for the multicast source when the device runs IGMPv3.

This field displays Off if the timer is disabled and displays three hyphens (---) if the multicast source is specified in IGMP SSM mappings.

This field is displayed only when the device runs IGMPv3 or when the device is configured with IGMP SSM mappings.

Mapping expires

Remaining time for the multicast source specified in IGMP SSM mappings.

This field is displayed only when the device is configured with IGMP SSM mappings.

Last-member-query-counter

Number of IGMP group-specific queries or IGMP group-and-source-specific queries sent for the multicast source and group.

This field is displayed only when the device runs IGMPv3 or is configured with IGMP SSM mappings.

Last-member-query-timer-expiry

Remaining time for the last member query timer for the multicast source and group.

This field displays Off if the timer is disabled.

This field is displayed only when the device runs IGMPv3 or is configured with IGMP SSM mappings.

 

# Display information about IGMP multicast groups that hosts have statically joined.

<Sysname> display igmp group static

 Entries in total: 2

   Group address   Source address  Interface           Expires

   225.1.1.1       0.0.0.0         Vlan1               Never

   225.2.2.2       1.1.1.1         Vlan1               Never

Table 3 Command output

Field

Description

Entries in total

Total number of the multicast groups that hosts have joined statically.

Group address

Multicast group address.

Source address

Multicast source address.

Interface

Interface name.

Expires

Remaining lifetime for the multicast group. This field always displays Never because the multicast group never expires.

 

Related commands

reset igmp group

display igmp interface

Use display igmp interface to display IGMP information for interfaces.

Syntax

display igmp interface [ interface-type interface-number ] [ proxy ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays IGMP information for all IGMP-enabled interfaces.

proxy: Displays the IGMP proxy interface information. If you do not specify this keyword, the command displays IGMP information about all interfaces.

verbose: Displays detailed IGMP information.

Examples

# Display detailed IGMP information for VLAN-interface 1 (non-proxy interface).

<Sysname> display igmp interface vlan-interface 1 verbose

 Vlan-interface1(10.10.1.20):

   IGMP is enabled.

   IGMP version: 2

   Query interval for IGMP: 125s

   Other querier present time for IGMP: 255s

   Maximum query response time for IGMP: 10s

   Last member query interval: 1s

   Last member query count: 2

   Startup query interval: 31s

   Startup query count: 2

   General query timer expiry (hh:mm:ss): 00:00:54

   Querier for IGMP: 10.10.1.20 (This router)

   IGMP activity: 1 join(s), 0 leave(s)

   Multicast routing on this interface: Enabled

   Robustness: 2

   Require-router-alert: Disabled

   Fast-leave: Disabled

   Startup-query: Off

   Other-querier-present-timer-expiry (hh:mm:ss): Off

   IGMP groups reported in total: 1

# Display detailed IGMP information for all IGMP proxy interfaces.

<Sysname> display igmp interface proxy verbose

 Vlan-interface2(20.10.1.20):

   IGMP proxy is enabled.

   IGMP version: 2

   Multicast routing on this interface: Enabled

   Require-router-alert: Disabled

   Version1-querier-present-timer-expiry (hh:mm:ss): Off

# Display detailed IGMP information for all interfaces enabled with the IGMP host feature.

<Sysname> display igmp interface host verbose

 Vlan-interface3(30.10.1.20):

   IGMP host is enabled.

   IGMP version: 2

   Multicast routing on this interface: Enabled

   Require-router-alert: Disabled

   Version1-querier-present-timer-expiry (hh:mm:ss): Off

Table 4 Command output

Field

Description

Vlan-interface1(10.10.1.20)

Interface and its IP address.

IGMP is enabled

IGMP is enabled on the interface.

IGMP version

Version of IGMP that the interface runs.

Query interval for IGMP

IGMP general query interval, in seconds.

Other querier present time for IGMP

IGMP other querier present interval, in seconds.

Maximum query response time for IGMP

Maximum response time for IGMP general queries, in seconds.

Last member query interval

Interval for sending IGMP group-specific queries or IGMP group-and-source-specific queries, in seconds.

Last member query count

Number of IGMP group-specific queries or IGMP group-and-source-specific queries sent for the multicast group.

Startup query interval

Interval for sending IGMP general queries on startup, in seconds.

Startup query count

Number of IGMP general queries that the device sends on startup.

General query timer expiry

Remaining time for the IGMP general query timer. This field displays Off if the timer is disabled.

Querier for IGMP

IP address of the IGMP querier.

This field is not displayed when the device runs IGMPv1 and the device is not the IGMP querier.

NOTE:

In IGMPv1, the PIM DR acts as the IGMP querier. You can use the display pim interface command to display PIM information.

No querier elected

No IGMP querier election is performed.

This field is displayed when the device runs IGMPv1 and is not the IGMP querier.

NOTE:

In IGMPv1, the PIM DR acts as the IGMP querier. You can use the display pim interface command to display PIM information.

IGMP activity: 1 join(s), 0 leave(s)

Statistics of IGMP activities:

·         join(s)—Total number of multicast groups that this interface has joined.

·         leave(s)—Total number of multicast groups that this interface has left.

Multicast routing on this interface

Whether IP multicast routing is enabled: Enabled or Disabled.

Robustness

Robustness variable of the IGMP querier.

Require-router-alert

Whether the feature of dropping IGMP messages without Router-Alert is enabled: Enabled or Disabled,

Fast-leave

Whether the fast-leave processing feature is enabled: Enabled or Disabled.

Startup-query

Whether the IGMP querier sends IGMP general queries at the startup query interval on startup:

·         OnThe IGMP querier performs the above action.

·         OffThe IGMP querier does not perform the above action.

Other-querier-present-timer-expiry

Remaining time for the other querier present timer. This field displays Off if the timer is disabled.

IGMP groups reported in total

Total number of multicast groups that the interface has joined dynamically.

This field is not displayed if the interface does not join multicast groups.

IGMP proxy is enabled

IGMP proxying is enabled on the interface.

IGMP host is enabled

The IGMP host feature is enabled on the interface.

Version1-querier-present-timer-expiry

Remaining time for the IGMPv1 querier present timer. This field displays Off if the timer is disabled.

 

display igmp proxy group

Use display igmp proxy group to display information about multicast groups maintained by the IGMP proxy.

Syntax

display igmp proxy group [ group-address | interface interface-type interface-number ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

group-address: Specifies a multicast group by its IP address in the range of 224.0.1.0 to 239.255.255.255. If you do not specify a multicast group, this command displays information about all multicast groups maintained by the IGMP proxy.

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays information about multicast groups maintained by the IGMP proxy for all interfaces.

verbose: Displays detailed information.

Examples

# Display information about multicast groups maintained by the IGMP proxy.

<Sysname> display igmp proxy group

IGMP proxy group records in total: 2

 Vlan-interface1(1.1.1.20):

  IGMP proxy group records in total: 2

   Group address      Member state      Expires

   225.1.1.1          Delay             00:00:02

   225.1.1.2          Idle              Off

# Display detailed information about multicast group 225.1.1.1 maintained by the IGMP proxy.

<Sysname> display igmp proxy group 225.1.1.1 verbose

 Vlan-interface1(1.1.1.20):

  IGMP proxy group records in total: 2

   Group: 225.1.1.1

     Group mode: Include

     Member state: Delay

     Expires: 00:00:02

     Source list (sources in total: 1):

       1.1.1.1

Table 5 Command output

Field

Description

IGMP groups records in total

Total number of multicast groups maintained by the IGMP proxy.

Vlan-interface1(1.1.1.20)

IGMP proxy interface and its IP address.

Pending proxy group

Pending multicast groups maintained by the IGMP proxy.

Group address/Group

Multicast group address.

Member state

Member host states:

·         Delay—The member host has joined a group and started a delay timer.

·         Idle—The member host has joined a group, but didn't start a delay timer.

Expires

Remaining delay time for the member host to send a responding report. This field displays Off if the timer is disabled.

Group mode

Multicast source filtering mode: Include or Exclude.

Source list

Multicast source list for the multicast group maintained by the IGMP proxy.

sources in total

Total number of multicast sources.

 

display igmp proxy routing-table

Use display igmp proxy routing-table to display multicast routing entries maintained by the IGMP proxy.

Syntax

display igmp proxy routing-table [ source-address [ mask { mask-length | mask } ] | group-address [ mask { mask-length | mask } ] ] * [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

source-address: Specifies a multicast source by its IP address. If you do not specify a multicast source, this command displays multicast routing entries for all multicast sources maintained by the IGMP proxy.

group-address: Specifies a multicast group address by its IP address in the range of 224.0.1.0 to 239.255.255.255. If you do not specify a multicast group, this command displays multicast routing entries for all multicast groups maintained by the IGMP proxy.

mask-length: Specifies a mask length of the multicast group address or multicast source address. For a multicast source address, the value range for this argument is 0 to 32. For a multicast group address, the value range for this argument is 4 to 32. The default value is 32 in both cases.

mask: Specifies a mask of the multicast group address or multicast source address. The default value is 255.255.255.255.

verbose: Displays detailed information about multicast routing entries maintained by the IGMP proxy.

Examples

# Display multicast routing entries maintained by the IGMP proxy.

<Sysname> display igmp proxy routing-table

 Total 1 (*, G) entries, 2 (S, G) entries.

 

 (172.168.0.12, 227.0.0.1)

     Upstream interface: Vlan-interface1

     Downstream interfaces (1 in total):

         1: Vlan-interface2

             Protocol: IGMP

 

 (*, 225.1.1.1)

     Upstream interface: Vlan-interface1

     Downstream interfaces (1 in total):

         1: Vlan-interface2

             Protocol: STATIC

 

 (2.2.2.2, 225.1.1.1)

     Upstream interface: Vlan-interface1

     Downstream interfaces (2 in total):

         1: LoopBack1

             Protocol: STATIC

         2: Vlan-interface2

             Protocol: PROXY

# Display detailed information about multicast routing entries maintained by the IGMP proxy.

<Sysname> display igmp proxy routing-table verbose

 Total 1 (*, G) entries, 2 (S, G) entries.

 

 (172.168.0.12, 227.0.0.1)

     Upstream interface: Vlan-interface1

     Downstream interfaces (1 in total):

         1: Vlan-interface2

             Protocol: IGMP

             Querier state: Querier

             Join/Prune state:Join

 

     Non-downstream interfaces: None

 

 (*, 225.1.1.1)

     Upstream interface: Vlan-interface1

     Downstream interfaces (1 in total):

         1: Vlan-interface2

             Protocol: STATIC

             Querier state: Querier

             Join/Prune state:Join

 

     Non-downstream interfaces (1 in total):

         1: Vlan-interface3

             Protocol: IGMP

             Querier state: Non-querier

             Join/Prune state:Join

 

 (2.2.2.2, 225.1.1.1)

     Upstream interface: Vlan-interface1

     Downstream interfaces (2 in total):

         1: LoopBack1

             Protocol: STATIC

             Querier state: Querier

             Join/Prune state: Join

         2: Vlan-interface2

             Protocol: PROXY

             Querier state: Querier

             Join/Prune state: Join

 

     Non-downstream interfaces: None

Table 6 Command output

Field

Description

Total 1 (*, G) entries, 2 (S, G) entries

Total number of (*, G) entries, and the total number of (S, G) entries.

(172.168.0.12, 227.0.0.1)

(S, G) entry.

Upstream interface

Incoming interface of the (S, G) entry.

Downstream interfaces (1 in total)

Outgoing interfaces of the (S, G) entry, and the total number of outgoing interfaces.

Non-downstream interfaces (1 in total)

Non-outgoing interfaces of the (S, G) entry, and the total number of non-outgoing interfaces.

1: Vlan-interface2

Index of an interface, and the interface.

Protocol

Protocol type:

·         IGMP—Dynamic IGMP.

·         PROXY—IGMP proxy.

·         STATIC—Static IGMP.

Querier state

Querier state:

·         Querier.

·         Non-querier.

Join/Prune state

Joined or pruned state of the interface:

·         NI—Default state.

·         Join—Joined state.

·         Prune—Pruned state.

 

display igmp ssm-mapping

Use display igmp ssm-mapping to display IGMP SSM mappings.

Syntax

display igmp ssm-mapping group-address

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

group-address: Specifies a multicast group by its IP address in the range of 224.0.1.0 to 239.255.255.255.

Examples

# Display IGMP SSM mappings for multicast group 232.1.1.1.

<Sysname> display igmp ssm-mapping 232.1.1.1

 Group: 232.1.1.1

 Source list:

        1.2.3.4

        5.5.5.5

        10.1.1.1

        100.1.1.10

Table 7  Command output

Field

Description

Group

Multicast group address.

Source list

List of multicast source addresses.

 

dscp

Use dscp to set the DSCP value for outgoing IGMP protocol packets.

Use undo dscp to restore the default.

Syntax

dscp dscp-value

undo dscp

Default

The DSCP value is 48 for outgoing IGMP protocol packets.

Views

IGMP view

Predefined user roles

network-admin

Parameters

dscp-value: Specifies a DSCP value in the range of 0 to 63.

Usage guidelines

The DSCP value is carried in the ToS field of an IP packet to determine the transmission priority of the packet. A greater DSCP value represents a higher priority.

Examples

# Set the DSCP value to 63 for outgoing IGMP protocol packets.

<Sysname> system-view

[Sysname] igmp

[Sysname-igmp] dscp 63

igmp

Use igmp to enter IGMP view.

Use undo igmp to delete the configurations in IGMP view.

Syntax

igmp

undo igmp

Views

System view

Predefined user roles

network-admin

Examples

# Enter IGMP view.

<Sysname> system-view

[Sysname] igmp

[Sysname-igmp]

igmp enable

Use igmp enable to enable IGMP on an interface.

Use undo igmp enable to disable IGMP on an interface.

Syntax

igmp enable

undo igmp enable

Default

IGMP is disabled on an interface.

Views

Interface view

Predefined user roles

network-admin

Usage guidelines

This command takes effect only when IP multicast routing is enabled.

Other IGMP configurations on the interface take effects only when IGMP is enabled on the interface.

Examples

# Enable IP multicast routing, and enable IGMP on VLAN-interface 100.

<Sysname> system-view

[Sysname] multicast routing

[Sysname-mrib] quit

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp enable

Related commands

multicast routing

igmp fast-leave

Use igmp fast-leave to enable fast-leave processing on an interface.

Use undo igmp fast-leave to disable fast-leave processing on an interface.

Syntax

igmp fast-leave [ group-policy ipv4-acl-number ]

undo igmp fast-leave

Default

Fast-leave processing is disabled. The IGMP querier sends IGMP group-specific or group-and-source-specific queries after receiving a leave message.

Views

Interface view

Predefined user roles

network-admin

Parameters

ipv4-acl-number: Specifies an IPv4 basic ACL by its number in the range of 2000 to 2999. If you specify an ACL, the fast-leave processing feature takes effect only on the multicast groups that the ACL permits. The feature takes effect on all multicast groups when one of the following conditions exists:

·          You do not specify an ACL.

·          The specified ACL does not exist.

·          The specified ACL does not have valid rules.

Usage guidelines

The fast-leave processing feature enables an IGMP querier to suppress IGMP group-specific or group-and-source-specific queries upon receiving IGMP leave messages permitted by the ACL.

When you configure a rule in the IPv4 basic ACL, follow these restrictions and guidelines:

·          The source source-address source-wildcard option specifies a multicast group address.

·          Among the other optional parameters, only the fragment keyword and the time-range time-range-name option take effect.

Examples

# Enable fast-leave processing on VLAN-interface 100.

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp fast-leave

igmp group-policy

Use igmp group-policy to configure a multicast group policy on an interface to control the multicast groups that hosts attached to the interface can join.

Use undo igmp group-policy to delete the multicast group policy on an interface.

Syntax

igmp group-policy ipv4-acl-number [ version-number ]

undo igmp group-policy

Default

No multicast group policy exists on an interface. Hosts attached to the interface can join any multicast groups.

Views

Interface view

Predefined user roles

network-admin

Parameters

ipv4-acl-number: Specifies an IPv4 basic or advanced ACL by its number in the range of 2000 to 3999. Hosts can join only the multicast groups that the ACL permits. If the ACL does not exist or does not have valid rules, hosts cannot join any multicast groups.

version-number: Specifies an IGMP version in the range of 1 to 3. By default, this command takes effect on IGMP reports of all versions.

Usage guidelines

A multicast group policy filters IGMP reports to control the multicast groups that the hosts can join.

This command does not take effect on static member interfaces because static member interfaces do not send IGMP reports.

When you configure a rule in the IPv4 ACL, follow these restrictions and guidelines:

·          In a basic ACL, the source source-address source-wildcard option specifies a multicast group address.

·          In an advanced ACL, the source source-address source-wildcard option specifies a multicast source address. The destination dest-address dest-wildcard option specifies a multicast group address.

To match the following IGMP reports, set the source source-address source-wildcard option to 0.0.0.0:

¡  IGMPv1 and IGMPv2 reports.

¡  IGMPv3 IS_EX and IGMPv3 TO_EX reports that do not carry multicast source addresses.

·          Among the other optional parameters, only the fragment keyword and the time-range time-range-name option take effect.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Configure a multicast group policy on VLAN-interface 100 so that hosts attached to the interface can join only multicast group 225.1.1.1.

<Sysname> system-view

[Sysname] acl basic 2005

[Sysname-acl-ipv4-basic-2005] rule permit source 225.1.1.1 0

[Sysname-acl-ipv4-basic-2005] quit

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp group-policy 2005

igmp last-member-query-count

Use igmp last-member-query-count to set the IGMP last member query count on an interface.

Use undo igmp last-member-query-count to restore the default.

Syntax

igmp last-member-query-count count

undo igmp last-member-query-count

Default

The IGMP last member query count equals the IGMP querier's robustness variable.

Views

Interface view

Predefined user roles

network-admin

Parameters

count: Specifies an IGMP last member query count in the range of 1 to 255.

Usage guidelines

You can set the IGMP last member query count for an interface in interface view or globally for all interfaces in IGMP view. For an interface, the interface-specific configuration takes priority over the global configuration.

Examples

# Set the IGMP last member query count to 6 on VLAN-interface 100.

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp last-member-query-count 6

Related commands

last-member-query-count (IGMP view)

igmp last-member-query-interval

Use igmp last-member-query-interval to set the IGMP last member query interval on an interface.

Use undo igmp last-member-query-interval to restore the default.

Syntax

igmp last-member-query-interval interval

undo igmp last-member-query-interval

Default

The IGMP last member query interval is 1 second.

Views

Interface view

Predefined user roles

network-admin

Parameters

interval: Specifies an IGMP last member query interval in the range of 1 to 25 seconds.

Usage guidelines

You can set the IGMP last member query interval for an interface in interface view or globally for all interfaces in IGMP view. For an interface, the interface-specific configuration takes priority over the global configuration.

Examples

# Set the IGMP last member query interval to 6 seconds on VLAN-interface 100.

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp last-member-query-interval 6

Related commands

last-member-query-interval (IGMP view)

igmp max-response-time

Use igmp max-response-time to set the maximum response time for IGMP general queries on an interface.

Use undo igmp max-response-time to restore the default.

Syntax

igmp max-response-time time

undo igmp max-response-time

Default

The maximum response time for IGMP general queries is 10 seconds.

Views

Interface view

Predefined user roles

network-admin

Parameters

time: Specifies the maximum response time for IGMP general queries, in the range of 1 to 3174 seconds.

Usage guidelines

You can set the maximum response time for an interface in interface view or globally for all interfaces in IGMP view. For an interface, the interface-specific configuration takes priority over the global configuration.

Examples

# Set the maximum response time for IGMP general queries to 25 seconds on VLAN-interface 100.

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp max-response-time 25

Related commands

max-response-time (IGMP view)

igmp non-stop-routing

Use igmp non-stop-routing to enable IGMP NSR.

Use undo igmp non-stop-routing to disable IGMP NSR.

Syntax

igmp non-stop-routing

undo igmp non-stop-routing

Default

IGMP NSR is disabled.

Views

System view

Predefined user roles

network-admin

Examples

# Enable IGMP NSR.

<Sysname> system-view

[Sysname] igmp non-stop-routing

igmp other-querier-present-interval

Use igmp other-querier-present-interval to set the IGMP other querier present timer on an interface.

Use undo igmp other-querier-present-interval to restore the default.

Syntax

igmp other-querier-present-interval interval

undo igmp other-querier-present-interval

Default

The IGMP other querier present timer is calculated by using the following formula:

[ IGMP general query interval ] × [ IGMP querier's robustness variable ] + [ maximum response time for IGMP general queries ] / 2.

Views

Interface view

Predefined user roles

network-admin

Parameters

interval: Specifies an IGMP other querier present timer in the range of 1 to 31744 seconds.

Usage guidelines

You can set the IGMP other querier present timer for an interface in interface view or globally for all interfaces in IGMP view. For an interface, the interface-specific configuration takes priority over the global configuration.

Examples

# Set the IGMP other querier present timer to 125 seconds on VLAN-interface 100.

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp other-querier-present-interval 125

Related commands

other-querier-present-interval (IGMP view)

igmp proxy enable

Use igmp proxy enable to enable IGMP proxying on an interface.

Use to undo igmp proxy enable to disable IGMP proxying on an interface.

Syntax

igmp proxy enable

undo igmp proxy enable

Default

IGMP proxying is disabled on an interface.

Views

Interface view

Predefined user roles

network-admin

Usage guidelines

This command takes effect only when IP multicast routing is enabled.

Examples

# Enable IP multicast routing, and enable IGMP proxying on VLAN-interface 100.

<Sysname> system-view

[Sysname] multicast routing-enable

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp proxy enable

Related commands

multicast routing

igmp proxy forwarding

Use igmp proxy forwarding to enable multicast forwarding on a non-querier interface.

Use undo igmp proxy forwarding to disable multicast forwarding on a non-querier interface.

Syntax

igmp proxy forwarding

undo igmp proxy forwarding

Default

Multicast forwarding is disabled for a non-querier interface.

Views

Interface view

Predefined user roles

network-admin

Usage guidelines

Typically, only IGMP queriers can forward multicast traffic but non-queriers cannot. This mechanism prevents multicast data from being repeatedly forwarded. If a router interface on the IGMP proxy failed the querier election, enable multicast forwarding on the interface to forward multicast data to attached receivers.

Examples

# Enable multicast forwarding on VLAN-interface 100. (VLAN-interface 100 is a non-querier interface on the IGMP proxy device.)

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp proxy forwarding

igmp query-interval

Use igmp query-interval to set the IGMP general query interval on an interface.

Use undo igmp query-interval to restore the default.

Syntax

igmp query-interval interval

undo igmp query-interval

Default

The IGMP general query interval is 125 seconds.

Views

Interface view

Predefined user roles

network-admin

Parameters

interval: Specifies an IGMP general query interval in the range of 1 to 31744 seconds.

Usage guidelines

You can set the IGMP general query interval for an interface in interface view or globally for all interfaces in IGMP view. For an interface, the interface-specific configuration takes priority over the global configuration.

Examples

# Set the IGMP general query interval to 60 seconds on VLAN-interface 100.

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp query-interval 60

Related commands

query-interval (IGMP view)

igmp robust-count

Use igmp robust-count to set the IGMP querier's robustness variable on an interface.

Use undo igmp robust-count to restore the default.

Syntax

igmp robust-count count

undo igmp robust-count

Default

The IGMP querier's robustness variable is 2.

Views

Interface view

Predefined user roles

network-admin

Parameters

count: Specifies an IGMP querier's robustness variable in the range of 1 to 255.

Usage guidelines

The IGMP querier's robustness variable defines the number of times to retransmit queries if packet loss occurs. A higher robustness variable makes the IGMP querier more robust, but it increases timeout time for multicast groups.

You can set the IGMP querier's robustness variable for an interface in interface view or globally for all interfaces in IGMP view. For an interface, the interface-specific configuration takes priority over the global configuration.

Examples

# Set the IGMP querier's robustness variable to 5 on VLAN-interface 100.

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp robust-count 5

Related commands

robust-count (IGMP view)

igmp startup-query-count

Use igmp startup-query-count to set the IGMP startup query count on an interface.

Use undo igmp startup-query-count to restore the default.

Syntax

igmp startup-query-count count

undo igmp startup-query-count

Default

The IGMP startup query count equals the IGMP querier's robustness variable.

Views

Interface view

Predefined user roles

network-admin

Parameters

count: Specifies an IGMP startup query count in the range of 1 to 255.

Usage guidelines

You can set the IGMP startup query count for an interface in interface view or globally for all interfaces in IGMP view. For an interface, the interface-specific configuration takes priority over the global configuration.

Examples

# Set the IGMP startup query count to 5 on VLAN-interface 100.

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp startup-query-count 5

Related commands

startup-query-count (IGMP view)

igmp startup-query-interval

Use igmp startup-query-interval to set the IGMP startup query interval on an interface.

Use undo igmp startup-query-interval to restore the default.

Syntax

igmp startup-query-interval interval

undo igmp startup-query-interval

Default

The IGMP startup query interval equals one quarter of the IGMP general query interval.

Views

Interface view

Predefined user roles

network-admin

Parameters

interval: Specifies an IGMP startup query interval in the range of 1 to 31744 seconds.

Usage guidelines

You can set the IGMP startup query interval for an interface in interface view or globally for all interfaces in IGMP view. For an interface, the interface-specific configuration takes priority over the global configuration.

Examples

# Set the IGMP startup query interval to 100 seconds on VLAN-interface 100.

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp startup-query-interval 100

Related commands

startup-query-interval (IGMP view)

igmp static-group

Use igmp static-group to configure an interface as a static group member of a multicast group.

Use undo igmp static-group to restore the default.

Syntax

igmp static-group group-address [ source source-address ]

undo igmp static-group { all | group-address [ source source-address ]

Default

An interface is not a static group member of multicast groups.

Views

Interface view

Predefined user roles

network-admin

Parameters

group-address: Specifies a multicast group by its IP address in the range of 224.0.1.0 to 239.255.255.255.

source source-address: Specifies a multicast source by its IP address. If you do not specify a multicast source, this command configures an interface as a static member of the multicast groups with all multicast source addresses.

all: Specifies all multicast groups that the interface has statically joined.

Usage guidelines

For multicast routing entries to be created, you must specify a multicast source if the specified multicast group is in the SSM group range.

Examples

# Configure VLAN-interface 100 as a static group member of multicast group 224.1.1.1.

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp static-group 224.1.1.1

# Configure VLAN-interface 100 as a static group member of multicast source and group (192.168.1.1, 232.1.1.1).

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp static-group 232.1.1.1 source 192.168.1.1

igmp version

Use igmp version to specify an IGMP version on an interface.

Use undo igmp version to restore the default.

Syntax

igmp version version-number

undo igmp version

Default

The IGMP version on an interface is 2.

Views

Interface view

Predefined user roles

network-admin

Parameters

version-number: Specifies an IGMP version in the range of 1 to 3.

Examples

# Specify IGMP version 1 on VLAN-interface 100.

<Sysname> system-view

[Sysname] interface vlan-interface 100

[Sysname-Vlan-interface100] igmp version 1

last-member-query-count (IGMP view)

Use last-member-query-count to set the IGMP last member query count globally.

Use undo last-member-query-count to restore the default.

Syntax

last-member-query-count count

undo last-member-query-count

Default

The IGMP last member query count equals the IGMP querier's robustness variable.

Views

IGMP view

Predefined user roles

network-admin

Parameters

count: Specifies an IGMP last member query count in the range of 1 to 255.

Usage guidelines

You can set the IGMP last member query count globally for all interfaces in IGMP view or for an interface in interface view. For an interface, the interface-specific configuration takes priority over the global configuration.

Examples

# Set the global IGMP last member query count to 6.

<Sysname> system-view

[Sysname] igmp

[Sysname-igmp] last-member-query-count 6

Related commands

igmp last-member-query-count

last-member-query-interval (IGMP view)

Use last-member-query-interval to set the IGMP last member query interval globally.

Use undo last-member-query-interval to restore the default.

Syntax

last-member-query-interval interval

undo last-member-query-interval

Default

The IGMP last member query interval is 1 second.

Views

IGMP view

Predefined user roles

network-admin

Parameters

interval: Specifies an IGMP last member query interval in the range of 1 to 25 seconds.

Usage guidelines

You can set the IGMP last member query interval globally for all interfaces in IGMP view or for an interface in interface view. For an interface, the interface-specific configuration takes priority over the global configuration.

Examples

# Set the global IGMP last member query interval to 6 seconds.

<Sysname> system-view

[Sysname] igmp

[Sysname-igmp] last-member-query-interval 6

Related commands

igmp last-member-query-interval

max-response-time (IGMP view)

Use max-response-time to set the maximum response time for IGMP general queries globally.

Use undo max-response-time to restore the default.

Syntax

max-response-time time

undo max-response-time

Default

The maximum response time for IGMP general queries is 10 seconds.

Views

IGMP view

Predefined user roles

network-admin

Parameters

time: Specifies the maximum response time for IGMP general queries in the range of 1 to 3174 seconds.

Usage guidelines

You can set the maximum response time globally for all interfaces in IGMP view or for an interface in interface view. For an interface, the interface-specific configuration takes priority over the global configuration.

Examples

#Set the global maximum response time for IGMP general queries to 25 seconds.

<Sysname> system-view

[Sysname] igmp

[Sysname-igmp] max-response-time 25

Related commands

igmp max-response-time

other-querier-present-interval (IGMP view)

Use other-querier-present-interval to set the IGMP other querier present timer globally.

Use undo other-querier-present-interval to restore the default.

Syntax

other-querier-present-interval interval

undo other-querier-present-interval

Default

The IGMP other querier present timer is calculated by using the following formula:

[ IGMP general query interval ] × [ IGMP querier's robustness variable ] + [ maximum response time for IGMP general queries ] / 2.

Views

IGMP view

Predefined user roles

network-admin

Parameters

interval: Specifies an IGMP other querier present timer in the range of 1 to 31744 seconds.

Usage guidelines

You can set the IGMP other querier present timer globally for all interfaces in IGMP view or for an interface in interface view. For an interface, the interface-specific configuration takes priority over the global configuration.

Examples

# Set the global IGMP other querier present timer to 125 seconds.

<Sysname> system-view

[Sysname] igmp

[Sysname-igmp] other-querier-present-interval 125

Related commands

igmp other-querier-present-interval

proxy multipath (IGMP view)

Use proxy multipath to enable load splitting on an IGMP proxy device.

Use undo proxy multipath to disable load splitting on an IGMP proxy device.

Syntax

proxy multipath

undo proxy multipath

Default

The load splitting feature is disabled on the IGMP proxy device.

Views

IGMP view

Predefined user roles

network-admin

Usage guidelines

Use this feature when the IGMP proxy device has multiple proxy interfaces. All proxy interfaces on the IGMP proxy device share multicast traffic on a per-group basis. If you do not enable this feature, only the proxy interface with the highest IP address forwards multicast data.

Examples

# Enable load splitting on the IGMP proxy device.

<Sysname> system-view

[Sysname] igmp

[Sysname-igmp] proxy multipath

query-interval (IGMP view)

Use query-interval to set the IGMP general query interval globally.

Use undo query-interval to restore the default.

Syntax

query-interval interval

undo query-interval

Default

The IGMP general query interval is 125 seconds.

Views

IGMP view

Predefined user roles

network-admin

Parameters

interval: Specifies an IGMP general query interval in the range of 1 to 31744 seconds.

Usage guidelines

You can set the IGMP general query interval globally for all interfaces in IGMP view or for an interface in interface view. For an interface, the interface-specific configuration takes priority over the global configuration.

Examples

# Set the global IGMP general query interval to 60 seconds.

<Sysname> system-view

[Sysname] igmp

[Sysname-igmp] query-interval 60

Related commands

igmp query-interval

reset igmp group

Use reset igmp group to clear dynamic IGMP multicast group entries.

Syntax

reset igmp group { all | interface interface-type interface-number { all | group-address [ mask { mask | mask-length } ] [ source-address [ mask { mask | mask-length } ] ] } }

Views

User view

Predefined user roles

network-admin

Parameters

all: Specifies all interfaces (the first all), or all IGMP multicast groups (the second all).

interface-type interface-number: Specifies an interface by its type and number.

group-address: Specifies a multicast group by its IP address in the range of 224.0.0.0 to 239.255.255.255.

source-address: Specifies a multicast source address. If you do not specify a multicast source, this command clears dynamic IGMP multicast group entries for all multicast source addresses.

mask: Specifies an address mask. The default is 255.255.255.255.

mask-length: Specifies an address mask length. The default is 32. For a multicast group address, the value range for this argument is 4 to 32. For a multicast source address, the value range for this argument is 0 to 32.

Usage guidelines

This command might interrupt the multicast information transmission.

Examples

# Clear dynamic IGMP multicast group entries for all interfaces.

<Sysname> reset igmp group all

# Clear all dynamic IGMP multicast group entries for VLAN-interface 100.

<Sysname> reset igmp group interface vlan-interface 100 all

# Clear the dynamic IGMP multicast group entry of group 225.0.0.1 for VLAN-interface 100.

<Sysname> reset igmp group interface vlan-interface 100 225.0.0.1

Related commands

display igmp group

robust-count (IGMP view)

Use robust-count to set the IGMP querier's robustness variable globally.

Use undo robust-count to restore the default.

Syntax

robust-count count

undo robust-count

Default

The IGMP querier's robustness variable is 2.

Views

IGMP view

Predefined user roles

network-admin

Parameters

count: Specifies an IGMP querier's robustness variable in the range of 1 to 255.

Usage guidelines

The IGMP querier's robustness variable defines the number of times to retransmit queries if packet loss occurs. A higher robustness variable makes the IGMP querier more robust, but it increases the timeout time for multicast groups.

You can set the IGMP querier's robustness variable globally for all interfaces in IGMP view or for an interface in interface view. For an interface, the interface-specific configuration takes priority over the global configuration.

Examples

# Set the global IGMP querier's robustness variable to 5.

<Sysname> system-view

[Sysname] igmp

[Sysname-igmp] robust-count 5

Related commands

igmp robust-count

ssm-mapping (IGMP view)

Use ssm-mapping to configure an IGMP SSM mapping.

Use undo ssm-mapping to delete IGMP SSM mappings.

Syntax

ssm-mapping source-address ipv4-acl-number

undo ssm-mapping { source-address | all }

Default

No IGMP SSM mappings exist.

Views

IGMP view

Predefined user roles

network-admin

Parameters

source-address: Specifies a multicast source by its IP address.

ipv4-acl-number: Specifies a basic ACL number in the range of 2000 to 2999. Multicast groups in IGMP reports permitted by the ACL are associated with the IPv6 multicast source. If the ACL does not exist or does not have valid rules, no multicast groups are associated with the IPv6 multicast source.

all: Specifies all IGMP SSM mappings.

Usage guidelines

When you configure a rule in the IPv4 basic ACL, follow these restrictions and guidelines:

·          The source source-address source-wildcard option specifies a multicast group address.

·          Among the other optional parameters, only the fragment keyword and the time-range time-range-name option take effect.

Examples

# Configure an IGMP SSM mapping with multicast source 125.1.1.1 and multicast group range 232.1.1.0/24.

<Sysname> system-view

[Sysname] acl basic 2001

[Sysname-acl-ipv4-basic-2001] rule permit source 232.1.1.1 0.0.0.255

[Sysname-acl-ipv4-basic-2001] quit

[Sysname] igmp

[Sysname-igmp] ssm-mapping 125.1.1.1 2001

Related commands

display igmp ssm-mapping

startup-query-count (IGMP view)

Use startup-query-count to set the IGMP startup query count globally.

Use undo startup-query-count to restore the default.

Syntax

startup-query-count count

undo startup-query-count

Default

The IGMP startup query count equals the IGMP querier's robustness variable.

Views

IGMP view

Predefined user roles

network-admin

Parameters

count: Specifies an IGMP startup query count in the range of 1 to 255.

Usage guidelines

You can set the IGMP startup query count globally for all interfaces in IGMP view or for an interface in interface view. For an interface, the interface-specific configuration takes priority over the global configuration.

Examples

# Set the global IGMP startup query count to 5.

<Sysname> system-view

[Sysname] igmp

[Sysname-igmp] startup-query-count 5

Related commands

igmp startup-query-count

startup-query-interval (IGMP view)

Use startup-query-interval to set the IGMP startup query interval globally.

Use undo startup-query-interval to restore the default.

Syntax

startup-query-interval interval

undo startup-query-interval

Default

The IGMP startup query interval equals one quarter of the IGMP general query interval.

Views

IGMP view

Predefined user roles

network-admin

Parameters

interval: Specifies an IGMP startup query interval in the range of 1 to 31744 seconds.

Usage guidelines

You can set the IGMP startup query interval globally for all interfaces in IGMP view or for an interface in interface view. For an interface, the interface-specific configuration takes priority over the global configuration.

Examples

# Set the global IGMP startup query interval to 100 seconds.

<Sysname> system-view

[Sysname] igmp

[Sysname-igmp] startup-query-interval 100

Related commands

igmp startup-query-interval