>

Table of Contents

H3C S9500 LSB1XK1 Series Card Manual(V1.01)

Download

                                                                                      1端口10GBase-XENPAK光接口板 – LSB1XK1

单板标识

LSB1XK1系列单板包括LSB1XK1B0 LSB1XK1CA0 LSB1XK1DB0 。前面板右上角分别标有丝印:XK1B XK1CA XK1DB,用来标识特定的单板。

单板简介

                                                                                                                                                                                                1 单板属性

属性

规格

接口连接器类型

XENPAK/SC

接口数量

1XENPAK/SC/电接口

接口传输速率

10Gbps

单板适用的机型

S9502/S9505/S9508/S9508V/S9512

单板适用的主机软件版本

1272及以上版本

 

10Gbps光接口可选用的XENPAK光模块类型及其属性见下表。

                                                                                                                                                             2 XENPAK光接口模块描述

接口类型

中心波长

接口连接器类型

接口光纤规格

光纤传输距离

10GBASE-SR-XENPAK

850nm

SC

多模光纤

对于62.5um MMF w/ 160MHz*km光纤,最大传输距离26M

对于50um MMF w/ 500MHz*km光纤,最大传输距离82M

对于50um MMF w/ 2000MHz*km光纤,最大传输距离300M

10GBASE-LR-XENPAK

1310nm

单模光纤

10km

10GBASE-ER-XENPAK

1550nm

40km

 

注意事项

如主机软件版本不匹配,请联系该设备的销售商或集成商获取相应的主机软件版本;

单板安装说明及主机软件版本的升级方法请参见《H3C S9500系列路由交换机  安装手册》相关章节。

单板种类或规格可能随产品版本的变更而改变,请从公司网站http://www.h3c.com.cn主页上的“文档中心”获取最新资料。

 

 

杭州华三通信技术有限公司

 


                                                        1-Port 10GBase-XENPAK Optical Interface Card – LSB1XK1

1  Card Identifier

LSB1XK1 Series Cards include LSB1XK1B0, LSB1XK1CA0 and LSB1XK1DB0.The silkscreens, XK1B, XK1CA and XK1DB, are printed at the upper right corner of the front panel respectively to identify the cards.

2  Specifications

Table1  Card specifications

Item

Specification

Connector

XENPAK/SC4

Port quantity

One XENPAK/SC4 optical or copper port

Transmission rate

10Gbps

Applied to

S9502/S9505/S9508/S9508V/S9512

Host software version

Version 1272 and above

 

To have an optical port, you can use one of these XENPAK optical modules.

Table2  XENPAK Optical Module Attribute

XENPAK module

Central wavelength

Connector

Matching cable

Transmission segment

10GBASE-SR-XENPAK

850nm

SC

Multi mode optical fiber cable

26 m (85.3 ft) for 62.5um MMF w/ 160MHz*km optical fiber cable;
82 m (269 ft) for 50um MMF w/ 500MHz*km optical fiber cable
300 m (984 ft) for 50um MMF w/ 2000MHz*km optical fiber cable

10GBASE-LR-XENPAK

1310 nm

single mode optical fiber cable

10 km (6 mi)

10GBASE-ER-XENPAK

1550 nm

40 km (about 25 mi)

 

3  Note

If the host software version does not match the one applicable to the card, contact the vendor or the integrator for the right version.

For the introduction of card installation and host software upgrade, see the related part in H3C S9500 Series Routing Switches Installation Manual.

As board types or specifications might change with product versions, you may need to obtain the latest documents from Technical Support & Document link on H3C website http://www.h3c.com.

 

 

Hangzhou H3C Technologies Co., Ltd

 


download