1 单板标识
前面板右上角标有丝印：SRP1N6，用来标识该单板。
2 单板简介
SRP1N6单板上依次排列有CF卡接口、CF卡状态指示灯（CFS）、10Base-T/100Base-TX接口、RS232/485口、Console口、AUX口、系统复位键、业务板状态指示灯、SRP1N6状态指示灯（SFS、ACT、ALM、RUN）。
属性 | 规格 |
接口连接器类型 | RJ45 |
对外接口 | 1个Console口，支持交换机的本地配置管理 1个AUX口，支持交换机的远程拨号配置管理 1个升级、网管用10Base-T/100Base-TX接口 1个RS232/485口，使用POE功能时连接外置POE电源框。RS485支持级联，使用POE功能或者配置NEPS3500-AB时连接POE框和NEPS3500-AB 1个CF卡接口 |
接口传输速率 | Console口：≤115200bit/s，缺省为9600bit/s AUX口：≤38400bit/s，缺省为9600bit/s 10/100Base-TX接口：10M/100M半/全双工；MDIX |
可选用线缆及最大传输距离 | Console口：普通异步串行口电缆，传输距离≤15m AUX口：普通异步串行口电缆，传输距离≤15m 10/100Base-TX接口：5类双绞线，传输距离100m |
单板适用的机型 | S9505 |
单板适用的主机软件版本 | 1272及以上版本 |
3 注意事项
如主机软件版本不匹配，请联系该设备的销售商或集成商获取相应的主机软件版本；
单板安装说明及主机软件版本的升级方法请参见《H3C S9500系列路由交换机 安装手册》相关章节。
单板种类或规格可能随产品版本的变更而改变，请从公司网站http://www.h3c.com.cn主页上的“文档中心”获取最新资料。
杭州华三通信技术有限公司
Switch Routing Process Card – LSB1SRP1N6
The silkscreen SRP1N6 is printed at the upper right corner of the front panel to identify the card.
2 Specifications
On the front panel of SRP1N6, CF port, CF LED (CFS), 10Base-T/100Base-TX port, RS232/485 port, Console port, AUX port, RESET button, LPU status LEDs, SRP1N6 status LEDs (SFS, ACT, ALM, RUN) are arranged from left to right.
Table1 Card specifications
Item | Specification |
Connector | RJ45 |
External Ports | One Console port, for local configuration management One AUX port, for remote dialup configuration management One 10Base-T/100Base-TX port for system management and program upgrade One RS232/485 port, for connecting external PoE power frame the RS485 port supports cascading and is connected to the PoE power frame and NEPS3500-AB when the PoE function is enabled and NEPS3500-AB is configured. One CF port |
Transmission rate | For Console port: no more than 115200bit/s, 9600bit/s by default For AUX port: no more than 38400bit/s, 9600bit/s by default For Ethernet Interface: 10Mbps/100Mbps, half/full duplex, MDIX |
Cable and maximum transmission distance | For Console port: asynchronous serial cable with maximum transmission distance 15m. For AUX port: asynchronous serial cable with maximum transmission distance 15m. For 10/100Base-TX interface: Category 5 UTP with maximum transmission distance 100m. |
Applied to | S9505 |
Host software version | Version 1272 and above |
3 Note
If the host software version does not match the one applicable to the card, contact the vendor or the integrator for the right version.
For the introduction of card installation and host software upgrade, see the related part in H3C S9500 Series Routing Switches Installation Manual.
As board types or specifications might change with product versions, you may need to obtain the latest documents from Technical Support & Document link on H3C website http://www.h3c.com.
Hangzhou H3C Technologies Co., Ltd
