H3C S9500 LSB1P4G8CA0 Card Manual(V1.01)
4端口OC-3c-POS 光接口及8端口1000BASE-X SFP光接口板 – LSB1P4G8CA0
1 单板标识
前面板右上角标有丝印：P4G8CA，用来标识该单板。
2 单板简介
属性 | 规格 |
接口连接器类型 | SFP/LC |
接口数量 | 4端口OC-3c POS光接口，8端口千兆以太网光接口 |
接口传输速率 | POS口155Mbps，光口1000Mbps |
单板适用的机型 | S9502/S9505/S9508/S9508V/S9512 |
单板适用的主机软件版本 | 1272及以上版本 |
千兆接口可选用的SFP模块类型及其属性见下表。
表2 千兆SFP模块属性
SFP模块名称 | 中心波长 | 接口连接器类型 | 接口光纤规格 | 光纤最大传输距离 |
1000BASE-SX-SFP | 850nm | LC | 50/125µm多模光纤 | 550m |
62.5/125µm多模光纤 | 275m | |||
1000BASE-LX-SFP | 1310nm | 9/125µm单模光纤 | 10km | |
1000BASE-LH-SFP | 40km | |||
1000BASE-ZX-LR-SFP | 1550nm | |||
1000BASE-ZX-VR-SFP | 70km | |||
1000BASE-ZX-UR-SFP | 100km |
POS接口可选用的SFP模块类型及其属性见下表。
表3 百兆SFP模块属性
SFP模块名称 | 中心波长 | 接口连接器类型 | 接口光纤规格 | 光纤最大传输距离 |
100BASE-FX-MM-SFP | 1310nm | LC | 50/125µm多模光纤 | 2km |
62.5/125µm多模光纤 | ||||
100BASE-FX-SM-SFP | 9/125µm单模光纤 | 15km | ||
100BASE-FX-SM-LR-SFP | 40km | |||
100BASE-FX-SM-VR-SFP | 1550nm | 80km |
3 注意事项
如主机软件版本不匹配，请联系该设备的销售商或集成商获取相应的主机软件版本；
单板安装说明及主机软件版本的升级方法请参见《H3C S9500系列路由交换机 安装手册》相关章节。
单板种类或规格可能随产品版本的变更而改变，请从公司网站http://www.h3c.com.cn主页上的“文档中心”获取最新资料。
杭州华三通信技术有限公司
4 x OC-3c-POS Optical Interface+8 x 1000BASE-X SFP Optical Interface Card – LSB1P4G8CA0
The silkscreen, P4G8CA, is printed at the upper right corner of the front panel to identify the card.
2 Specifications
Table1 Card specifications
Item | Specification |
Connector | SFP/LC |
Port quantity | 4-Port POS Optical Interface and 8-Port Gigabit Ethernet Optical Interface |
Transmission rate | 155Mbps，1000Mbps |
Applied to | S9502/S9505/S9508/S9508V/S9512 |
Host software version | Version 1272 and above |
For supported 1000Base-X SFP modules, refer to the following table.
Table2 1000Base-X SFP Module Attribute
Optional SFP module | Central wavelength | Connector type | Fiber specifications | Maximum transmission distance |
1000BASE-SX-SFP | 850nm | LC | 50/125μm multi-mode optical fiber | 550m |
62.5/125μm multi-mode optical fiber | 275m | |||
1000BASE-LX-SFP | 1310nm | 9/125μm Single Mode optical fiber | 10km | |
1000BASE-LH-SFP | 40km | |||
1000BASE-ZX-LR-SFP | 1550nm | |||
1000BASE-ZX-VR-SFP | 70km | |||
1000BASE-ZX-UR-SFP | 100km |
For supported POS SFP modules, refer to the following table.
Table3 POS SFP Module Attribute
Optional SFP module | Central wavelength | Connector type | Fiber specifications | Maximum transmission distance |
100BASE-FX-MM-SFP | 1310nm | LC | 50/125µm multi-mode optical fiber | 2km |
62.5/125µm multi-mode optical fiber | ||||
100BASE-FX-SM-SFP | 9/125µm single-mode optical fiber | 15km | ||
100BASE-FX-SM-LR-SFP | 40km | |||
100BASE-FX-SM-VR-SFP | 1550nm | 80km |
3 Note
If the host software version does not match the one applicable to the card, contact the vendor or the integrator for the right version.
For the introduction of card installation and host software upgrade, see the related part in H3C S9500 Series Routing Switches Installation Manual.
As board types or specifications might change with product versions, you may need to obtain the latest documents from Technical Support & Document link on H3C website http://www.h3c.com.
Hangzhou H3C Technologies Co., Ltd
