H3C S5600 Series Ethernet Switches are
high-performance, high-density, easy-to-install, NMS-manageable intelligent
Ethernet switches which support wire-speed Layer2/3 switching.
Table 1-1 lists the models of H3C S5600
Series Ethernet Switches.
Table 1-1 Models of H3C S5600 Series
Ethernet Switches
|
Model
|
Number of 10/100/1000M electrical
ports
|
Number of 1000M SFP optical ports
|
Number of Console ports
|
|
S5600-26C
|
24
|
4
|
1
|
|
S5600-26C-PWR
|
|
S5600-26F
|
4
|
24
|
|
S5600-50C
|
48
|
4
|
|
S5600-50C-PWR
|
Each SFP port and the corresponding 10/100/1000M
Ethernet port form a Combo port. For
each Combo port, the SFP port and the 10/100/1000M Ethernet port cannot be used
at the same time. For the relationship between the
Combo ports and the Ethernet ports, refer to Table 1-2.
Table 1-2 Combo
port list
|
Switch model
|
Combo Port
|
Corresponding port
|
|
S5600-26C/S5600-26C-PWR/S5600-26F
|
25
|
22
|
|
26
|
24
|
|
27
|
21
|
|
28
|
23
|
|
S5600-50C/S5600-50C-PWR
|
49
|
46
|
|
50
|
48
|
|
51
|
45
|
|
52
|
47
|
l
The electrical ports of
S5600-26C-PWR/S5600-50C-PWR are capable of supplying -48 VDC power to remote
PDs (powered devices, such as S2016C, S2008B, S2016B, S2016-EI, and so on).
l
The S5600-26C-PWR/S5600-50C-PWR adopts PoE power
module, which provides AC/DC power to PD devices. When delivering the AC input,
the module can supply up to 300 W power. If more power is needed, use the DC
input or both AC and DC inputs to ensure the operation of all the connected
devices.
l
The S5600-26C-PWR/S5600-50C-PWR can also adopt
AC/DC dual input power module. In this case, however, the two types of switches
have no PoE function. And they function exactly like the S5600-26C and
S5600-50C.
I. Front panel
The S5600-26C/S5600-26C-PWR provides 24 x 10/100/1000Base-TX
Ethernet ports, one Console port, and four 1000 Mbps SFP Combo ports on its
front panel. Each SFP port and the corresponding 10/100/1000M Ethernet port
form a Combo port. For each Combo
port, the SFP port and the 10/100/1000M Ethernet port cannot be used at the
same time. For the relationship between the Combo ports
and the Ethernet ports, refer to Table 1-2.
Figure 1-1 shows the front panel of an S5600-26C
Ethernet switch.:
|
(1) 10/100/1000M auto-negotiation
Ethernet port status LEDs
|
|
(2) 1000 Mbps SFP Combo port LED
|
(3) Console port
|
|
(4) 7-segment digitron display
|
(5) Power LED
|
|
(6) DC LED
|
(7) Fabric LED
|
|
(8) Module LED
|
(9) Port mode LED
|
|
(10) Mode button
|
|
Figure 1-1 Front panel of the S5600-26C/S5600-26C-PWR
The S5600-26F provides 24 x 1000 Mbps SFP
optical ports, one Console port, and four 1000 Mbps RJ-45 Combo ports on its
front panel. Each SFP port and the corresponding 10/100/1000M Ethernet port
form a Combo port. For each Combo
port, the SFP port and the 10/100/1000M Ethernet port cannot be used at the
same time. For the relationship between the Combo ports
and the Ethernet ports, refer to Table 1-2.
Figure 1-2. shows the
front panel of an S5600-26F Ethernet switch.:
|
(1) SFP optical port status LED
|
|
(2) 10/100/1000M auto-negotiation
Ethernet port status LEDs: left one for speed, right one for duplex mode
|
|
(3) Console port
|
(4) 7-segment digitron display
|
|
(5) Power LED
|
(6) RPS LED
|
|
(7) Fabric LED
|
(8) Module LED
|
Figure 1-2 Front panel of the S5600-26F
The S5600-26C/S5600-26C-PWR provides one
power LED, one RPS LED, one fabric LED, one module LED, one mode LED, one 7-segment
digitron display, four pairs of 1000 Mbps SFP port status LEDs, and 24 pairs of
10/100/1000M port status LEDs on its front panel.
The S5600-26F provides one power LED, one
RPS LED, one fabric LED, one module LED, one 7-segment digitron display, 24
pairs of 1000 Mbps SFP port status LEDs, and four pairs of 10/100/1000M auto-negotiation
Ethernet port status LEDs on its front panel.
Table 1-3 and Table 1-4 describe respectively the LEDs on the S5600-26C/S5600-26C-PWR and
S5600-26F.
Table 1-3 LEDs on the S5600-26C/S5600-26C-PWR
|
LED
|
Mark
|
Status
|
Description
|
|
Mode
LED
|
Mode
|
Speed
|
Solid
green
|
The
port status LEDs are showing the speed of each port.
|
|
Duplex
|
Solid yellow
|
The port LEDs are showing the duplex
mode of each port.
|
|
PoE
|
Blinking green (at 1 Hz)
|
The port LEDs are showing the PoE
status of each port.
|
|
Power LED
|
PWR
|
Solid green
|
The switch is started normally.
|
|
Blinking green (at 1 Hz)
|
The system is running power-on
self-test (POST).
|
|
Solid red
|
The system fails the POST, or
there is another fault.
|
|
Blinking yellow (at 1 Hz)
|
Some ports fail the POST and do
not function.
|
|
OFF
|
The switch is power-off.
|
|
DC LED
|
RPS
|
Solid green
|
Both the AC power supply and the
DC input operate normally.
|
|
Solid yellow
|
The AC power supply fails or the
AC input is disconnected, while the DC input operates normally.
|
|
OFF
|
DC input is disconnected.
|
|
Fabric
LED
|
STK
|
Green
|
The
device is in the ring fabric status; the LED blinks quickly when the fabric
port is receiving or sending data.
|
|
Yellow
|
The
device is in the daisy chain fabric status; the LED blinks quickly when the
fabric port is receiving or sending data.
|
|
Blinking green (at 3 Hz)
|
This device is isolated from the
whole set of fabric devices (effective when this device is in the fabric
status).
|
|
OFF
|
Neither of the two fabric ports
is connected.
|
|
Module
LED
|
Module
(MOD)
|
Solid
green
|
The
module is seated and operates normally.
|
|
Blinking
yellow
|
The
module fails or is not supported.
|
|
OFF
|
No
module is installed.
|
|
7-segment
digitron display
|
Unit
|
POST
running
|
Blinking
green
|
The
POST ID of the in-process test is displayed:
|
|
POST
failed
|
Blinking
red
|
The
POST ID of the failed test blinks.
|
|
Software
downloading
|
Blinking
green
|
A light
bar rotates clockwise around the display during the downloading procedure.
|
|
Fan
failed
|
Solid
red
|
An
“F” is displayed.
|
|
Over
temperature alarm
|
Solid
red
|
A “t”
is displayed.
|
|
Speed
and duplex mode
|
Solid
green
|
UNIT
ID in the fabric; or “1” for a standalone unit is displayed.
|
|
PoE mode
|
Solid green
|
The utilization of the power
supply is displayed.
|
|
10/100/
1000M auto- negotiation Ethernet port status LED
|
—
|
Speed
mode
|
Green
|
The
port is operating at 1000 Mbps. The LED blinks quickly when the port is
receiving or sending data.
|
|
Yellow
|
The
port is operating at 10/100 Mbps. The LED blinks quickly when the port is
receiving or sending data.
|
|
Blinking
yellow (at 3 Hz)
|
The
port fails the POST.
|
|
OFF
|
The
port is not connected.
|
|
Duplex
mode
|
Green
|
The
port is operating in full duplex mode. The LED blinks quickly when the port
is receiving or sending data.
|
|
Yellow
|
The port is operating in half
duplex mode. The LED blinks quickly when the port is receiving or sending
data.
|
|
Blinking Yellow (3 Hz)
|
The port fails the POST.
|
|
OFF
|
The port is not connected.
|
|
PoE mode
|
Solid green
|
The port supplies power normally.
|
|
Blinking green (at 1 Hz)
|
The connected device requires
more power than the maximum power a port can supply.
The port cannot supply power
because the switch has reached its maximum power supplied.
|
|
Solid yellow
|
The port cannot supply power
because the connected device is not a PD.
The port cannot supply power due
to the power source failure of PoE.
|
|
Blinking yellow (3 Hz)
|
The port fails the POST.
|
|
OFF
|
The port does not supply power.
|
|
1000M Base SFP port mode LED
|
—
|
Speed mode
|
Green
|
The port is operating at 1000 Mbps.
The LED blinks quickly when the port is receiving or sending data.
|
|
Blinking yellow (3 Hz)
|
The port fails the POST.
|
|
OFF
|
The port is not connected.
|
|
Duplex mode
|
Green
|
The port is operating in 1000 Mbps
full duplex mode. The LED blinks quickly when the port is receiving or
sending data.
|
|
Blinking yellow (3 Hz)
|
The port fails the POST.
|
|
OFF
|
The port is not connected.
|
|
PoE mode
|
OFF
|
–
|
|
|
|
|
|
|
Table 1-4 LEDs
on the S5600-26F
|
LED
|
Mark
|
Status
|
Description
|
|
Power LED
|
PWR
|
Solid green
|
The switch is started normally.
|
|
Blinking green (at 1 Hz)
|
The system is running power-on
self-test (POST).
|
|
Solid red
|
The system fails the POST, or
there is another fault.
|
|
Blinking yellow (at 1 Hz)
|
Some ports fail the POST and do
not function.
|
|
OFF
|
The switch is power-off.
|
|
DC LED
|
RPS
|
Solid green
|
Both the AC power supply and the
DC input operate normally.
|
|
Solid yellow
|
The AC power supply fails or the
AC input is disconnected, while the DC input operates normally.
|
|
OFF
|
DC input is disconnected.
|
|
Fabric
LED
|
STK
|
Green
|
The
device is in the ring fabric status; the LED blinks quickly when the fabric
port is receiving or sending data.
|
|
Yellow
|
The device is in the daisy chain
fabric status; the LED blinks quickly when the fabric port is receiving or
sending data.
|
|
Blinking green (at 3 Hz)
|
This device is isolated from the
whole set of fabric devices (effective when this device is in the fabric
status).
|
|
OFF
|
Neither of the two fabric ports
is connected.
|
|
Module LED
|
Module (MOD)
|
Solid green
|
The module is seated and operates
normally.
|
|
Blinking yellow
|
The module fails or is not
supported.
|
|
OFF
|
No module is installed.
|
|
7-segment digitron display
|
Unit
|
POST running
|
Blinking green
|
The POST ID of the in-process
test is displayed:
|
|
POST failed
|
Blinking red
|
The POST ID of the failed test
blinks.
|
|
Software downloading
|
Blinking green
|
A light bar rotates clockwise
around the display during the downloading procedure.
|
|
Fan failed
|
Solid red
|
An “F” is displayed.
|
|
Over temperature alarm
|
Solid red
|
A “t” is displayed.
|
|
Speed and duplex mode
|
Solid green
|
UNIT ID in the fabric; or
“1” for a standalone unit is displayed.
|
|
10/100/ 1000M auto- negotiation
Ethernet port status LED
|
—
|
Speed mode
|
Green
|
The port is operating at 1000 Mbps.
The LED blinks quickly when the port is receiving or sending data.
|
|
Yellow
|
The port is operating at 10/100 Mbps.
The LED blinks quickly when the port is receiving or sending data.
|
|
Blinking yellow (at 3 Hz)
|
The port fails the POST.
|
|
OFF
|
The port is not connected.
|
|
Duplex mode
|
Green
|
The port is operating in full
duplex mode. The LED blinks quickly when the port is receiving or sending
data.
|
|
Yellow
|
The port is operating in half
duplex mode. The LED blinks quickly when the port is receiving or sending
data.
|
|
Blinking Yellow (3 Hz)
|
The port fails the POST.
|
|
OFF
|
The port is not connected.
|
|
1000Base SFP optical port status
LED
|
—
|
port status LED
|
Green
|
The port is operating at 1000 Mbps.
The LED blinks quickly when the port is receiving or sending data.
|
|
Blinking yellow (3 Hz)
|
The port fails the POST.
|
|
OFF
|
The port is not connected.
|
III. Console port
The S5600-26C/S5600-26C-PWR/S5600-26F
provides an EIA/TIA-232-compliant Console port, which enables you to configure
the switch from the local or remote site.
Table 1-5 Attributes
of the Console port
|
Item
|
Description
|
|
Connector
|
RJ-45
|
|
Standard
|
EIA/TIA-232
|
|
Baud rate
|
9600 bps (default), auto-negotiation
is supported
|
|
Services
|
Connection to an ASCII terminal
Connection to the serial port of
a local terminal (a PC for example) or a remote terminal (through a pair of
modems) running terminal emulation software
|
1.2.2 Rear Panel
I. Rear panel
The ports of the
AC/DC dual input power module and the PoE power module are exactly the same, so
only one rear panel illustration is shown below.
The S5600-26C/S5600-26C-PWR/S5600-26F provides
two sockets for pluggable power module, two fabric ports, one expansion slot, and
one grounding screw on its rear panel, as shown in the following figure.
|
(1) AC-input power socket for the power
module
|
(2) Expansion module
|
|
(3) Grounding screw
|
(4) Fabric ports
|
|
(5) Fabric port LEDs
|
(6) RPS LED
|
|
(7) DC-input power socket for the power
module
|
|
Figure 1-3 Rear
panel of the S5600-26C/S5600-26C-PWR/S5600-26F
II. Fabric port
The fabric port marked with “UP”
connects to a port of the same type on an upstream device; the fabric port
marked with “DOWN” connects to a port of the same type on a
downstream device.
Table 1-6 Fabric port LEDs
|
LED
|
Mark
|
Status
|
Indicate
|
|
Fabric
port LED
|
UP(DOWN)
|
Solid
green
|
The
fabric port is properly connected.
|
