Syntax
count times
undo count
View
NQA test group view
Parameter
times:
Number of probes in a test, in the range 1 to 15.
Description
Use the count command to configure
the number of probes in a test.
Use the undo count command to
restore the default.
By default, one probe is performed in a
test.
For a TCP test, one probe means one
connection; for a Jitter test, the number of packets sent in one probe depends
on the jitter-packetnum command; for an SNMP test, three packets are
sent in one probe; for other types of tests, one packet is sent for one probe.
If the number of probes in a test is
greater than 1, the system sends a second packet after it sends the first
packet and receives a response packet. If the system does not receive a
response packet, the system waits for the test timer to expire before sending a
second test packet. The process is repeated until the specified probes are
completed.
Example
# Configure the number of probes in a test
to 10.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
count 10
Syntax
datafill
text
undo datafill
View
NQA test group view
Parameter
text: String
of fill characters of a test packet, in the range 1 to 200.
Description
Use the datafill command to
configure a string of fill characters for a test packet.
Use the undo datafill command to
restore the default.
By default, the fill string for ICMP test
packets is the string corresponding to ASCII codes 00 to 09; starting from the
second byte, the fill string for UDP test packets is the string corresponding
to ASCII codes 00 to FF, with the first byte used for control.
The fill data of an NQA test packet can be
any string of characters. If the test packet is smaller than the fill data, the
system uses only the first part of the character string to encapsulate the
packet. If the test packet is larger than the fill data, the system fills the
character string cyclically to encapsulate the test packet until the packet is
full. For example, when the fill data is “abcd” and the size of a
test packet is “3”, “adc” is used to fill. When the
test packet size is “6”, “abcdab” is used to fill.
Note that the datafill command is
valid for an ICMP test and a UDP test.
Example
# Configure the string of fill characters
of a test packet to “abcd”.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test] datafill
abcd
Syntax
datasize
size
undo datasize
View
NQA test group view
Parameter
size: Size
of a test packet in bytes, in the range of 1 to 8100.
Description
Use the datasize command to
configure the size of a test packet, namely, an echo request packet (IP header
and ICMP header excluded).
Use the undo datasize command to
restore the size of a test request packet to the default value.
By default, the size of an ICMP test packet
is 56 bytes and that of a UDP test packet is 100 bytes.
Note that:
l
The datasize command is valid only for
ICMP and UDP tests.
l
For an ICMP test, if the value of the size
argument is less than 20, the system automatically fills ICMP test packets to
20 bytes. If you configure a string of fill characters, the system fills this
string in test packets. If you do not configure any string of fill characters,
the system fills the default character string in test packets and what you can
see is “.”.
l
When you perform a UDP test, the size of test
packets is subject to the configuration.
Example
# Configure the size of test packets to 50
bytes.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test] datasize
50
Syntax
description text
undo description
View
NQA test group view
Parameter
text:
Descriptive string of 1 to 200 characters for a test group.
Description
Use the description command to give
a brief description of a test group, usually, the test type or test purpose of
a test group.
Use the undo description command to
remove the description information.
By default, no descriptive string is
available to a test group.
Example
# Configure a descriptive string for a test
group as “icmp-test”.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
description icmp-test
1.1.5 destination-ip
Syntax
destination-ip ip-address
undo destination-ip
View
NQA test group view
Parameter
ip-address:
Destination IP address of a test request packet.
Description
Use the destination-ip command to
configure a destination IP address for a test request packet.
Use the undo destination-ip command
to remove the destination IP address.
By default, no destination IP address is
configured for a test request packet.
Related command: destination-port.
Example
# Set the destination IP address of a test
request packet to 10.1.1.1.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
destination-ip 10.1.1.1
1.1.6 destination-port
Syntax
destination-port port-number
undo destination-port
View
NQA test group view
Parameter
port-number:
Destination port number of a test request packet, in the range of 1 to 65535.
Description
Use the destination-port command to
configure a destination port number for a test request packet.
Use the undo destination-port
command to remove the destination port number.
By default, no destination port number is
configured for a test request packet.
Note that the destination-port
command is valid only for jitter, TCP-Private, and UDP-Private tests.
Related command: destination-ip
l
The destination-port command is
applicable to only jitter, TCP-Private, and UDP-Private tests.
l
You are not recommended to perform a TCP, UDP,
or jitter test on a known port(1 to 1023). Otherwise, the NQA test will fail or
the corresponding services of this port will be unavailable.
Example
# Set the destination port number of a test
request packet to 9000.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
destination-port 9000
1.1.7 display
nqa
Syntax
display nqa { results | history | jitter }
[ admin-name operation-tag ]
View
Any view
Parameter
results:
Displays the results of the last test.
history:
Displays the history records of tests.
jitter:
Displays the recorded delay jitter of UDP packet transmission in the last NQA
jitter test.
admin-name:
Name of the administrator who creates NQA test groups, a string of 1 to 32
characters.
operation-tag: Operation tag, a string of 1 to 32 characters.
Description
Use the display nqa to display
results of an NQA test or tests.
If neither of the test group arguments (admin-name
and operation-tag) is specified, results of all test groups are
displayed. Otherwise, results of only the specified test group(s) are
displayed.
Related command: test-enable.
Example
# Display the results of the last test.
<Sysname> display nqa results
administrator icmp
NQA entry(admin administrator, tag icmp)
test result:
Destination ip address: 169.254.10.2.1.1.1
Send operation times:
1 Receive response times: 0
Min/Max/Average Round Trip
Time: 0/0/0
Square-Sum of Round Trip Time: 0
Last succeeded test time:
0-00-00 00:00:00.0
Extend result:
Packet lost in test: 100%
Failures due to Timeout: 0
Failures due to System Busy: 0
Failures due to Disconnect: 0
Failures due to No Connection:
0
Failures due to Sequence Error:
0
Failures due to Internal Error:
1
Failures due to Other Errors: 0
Table 1-1
Description on fields of the display nqa results command
|
Field
|
Description
|
|
Destination ip address
|
IP address of the destination
|
|
Send operation times
|
Number of sent probe packets
|
|
Receive responds times
|
Number of received response packets
|
|
Min/Max/Average Round Trip Time
|
Minimum/maximum/average roundtrip time
|
|
Square-Sum of Round Trip Time
|
Square sum of roundtrip time
|
|
Last succeeded test time
|
Completion time of the last successful
test
|
|
SD Maximal delay
|
Maximum delay from the source to the
destination
|
|
DS Maximal delay
|
Maximum delay from the destination to the
source
|
|
Packet lost in test
|
Average packet loss ratio
|
|
Disconnect operation number
|
Number of disconnections by the peer
|
|
Failures due to Timeout
|
Number of time-out occurrences in a test
|
|
Failures due to System Busy
|
Number of test failures owing to the
system being busy
|
|
Failures due to Disconnect
|
Number of disconnections by the peer
|
|
Failures due to No Connection
|
Number of failures to connect with the
peer
|
|
Failures due to Sequence Error
|
Number of failures owing to
out-of-sequence packets
|
|
Failures due to Internal Error
|
Number of failures owing to internal errors
|
|
Failures due to Other Errors
|
Number of failures owing to other errors
|
#: Display the history records of tests.
<Sysname> display nqa history
administrator test
NQA entry(admin administrator, tag test)
history record:
Index Response Status
LastRC Time
1 1 1
0 2004-11-25 16:28:55.0
2 1 1
0 2004-11-25 16:28:55.0
3 1 1
0 2004-11-25 16:28:55.0
4 1 1
0 2004-11-25 16:28:55.0
5 1 1
0 2004-11-25 16:28:55.0
6 2
1 0 2004-11-25 16:28:55.0
7 1 1
0 2004-11-25 16:28:55.0
8 1 1
0 2004-11-25 16:28:55.0
9 1 1
0 2004-11-25 16:28:55.9
10 1 1
0 2004-11-25 16:28:55.9
Table 1-2
Description on fields of the display nqa history command
|
Field
|
Description
|
|
Index
|
History record number
|
|
Response
|
Roundtrip delay of a test packet in the
case of a successful test, time-out time in the case of time-out, or 0 in the
case of a test failure (in seconds)
|
|
Status
|
Status value of test results, including:
1: responseReceived
2: unknown
3: internalError
4: requestTimedOut
5: unknownDestinationAddress
6: noRouteToTarget
7: interfaceInactiveToTarget
8: arpFailure
9: maxConcurrentLimitReached
10: unableToResolveDnsName
11: invalidHostAddress
|
|
LastRC
|
Temporarily, this field is not supported.
|
|
Time
|
Time when the test is completed
|
# Display the recorded delay jitter of UDP
packet transmission in the last NQA jitter test.
<Sysname> display nqa jitter
admin jitter
NQA entry(admin admin, tag jitter)
test jitter result:
RTT Number: 10
SD Maximal delay:
2 DS Maximal delay: 2
Min
Positive SD: 1 Min Positive DS: 1
Max Positive
SD: 1 Max Positive DS: 1
Positive
SD Number: 4 Positive DS Number: 2
Positive SD Sum:
4 Positive DS Sum: 2
Positive SD average:
1 Positive DS average: 1
Positive SD Square Sum:
4 Positive DS Square Sum: 2
Min
Negative SD: 1 Min Negative DS: 1
Max
Negative SD: 2 Max Negative DS: 1
Negative SD Number:
2 Negative DS Number: 3
Negative SD Sum:
3 Negative DS Sum: 3
Negative SD average:
2 Negative DS average: 1
Negative SD Square Sum:
5 Negative DS Square Sum: 3
SD lost packets number:
0 DS lost packet number: 0
Unknown result lost packet
number: 0
Table 1-3
Description on fields of the display nqa jitter command
|
Field
|
Description
|
|
RTT Number
|
Number of received response packets
|
|
SD Maximal delay
|
Maximum delay from the source to the
destination
|
|
DS Maximal delay
|
Maximum delay from the destination to the
source
|
|
Min Positive SD
|
Minimum positive jitter delay from the
source to the destination
|
|
Min Positive DS
|
Minimum positive jitter delay from the
destination to the source
|
|
Max Positive SD
|
Maximum positive jitter delay from the
source to the destination
|
|
Max Positive DS
|
Maximum positive jitter delay from the
destination to the source
|
|
Positive SD Number
|
Number of positive jitter delays from the
source to the destination
|
|
Positive DS Number
|
Number of positive jitter delays from the
destination to the source
|
|
Positive SD Sum
|
Sum of positive jitter delays from the
source to the destination
|
|
Positive DS Sum
|
Sum of positive jitter delays from the
destination to the source
|
|
Positive SD average
|
Average of positive jitter delays from
the source to the destination
|
|
Positive DS average
|
Average of positive jitter delays from
the destination to the source
|
|
Positive SD Square Sum
|
Sum of the square of positive jitter
delays from the source to the destination
|
|
Positive DS Square Sum
|
Sum of the square of positive jitter
delays from the destination to the source
|
|
Min Negative SD
|
Minimum absolute value of negative jitter
delays from the source to the destination
|
|
Min Negative DS
|
Minimum absolute value of negative jitter
delays from the destination to the source
|
|
Max Negative SD
|
Maximum absolute value of negative jitter
delays from the source to the destination
|
|
Max Negative DS
|
Maximum absolute value of negative jitter
delays from the destination to the source
|
|
Negative SD Number
|
Number of negative jitter delays from the
source to the destination
|
|
Negative DS Number
|
Number of negative jitter delays from the
destination to the source
|
|
Negative SD Sum
|
Sum of absolute values of negative jitter
delays from the source to the destination
|
|
Negative DS Sum
|
Sum of absolute values of negative jitter
delays from the destination to the source
|
|
Negative SD average
|
Average of negative jitter delays from
the source to the destination
|
|
Negative DS average
|
Average of negative jitter delays from
the destination to the source
|
|
Negative SD Square Sum
|
Sum of the square of negative jitter
delays from the source to the destination
|
|
Negative DS Square Sum
|
Sum of the square of negative jitter
delays from the destination to the source
|
|
SD lost packets number
|
Number of lost packets from the source to
the destination
|
|
DS lost packet number
|
Number of lost packets from the
destination to the source
|
|
Unknown result lost packet number
|
Number of lost packets for unknown
reasons
|
Syntax
filename file-name
undo filename
View
NQA test group view
Parameter
file-name:
Name of the file transferred between the FTP server and the FTP client, a
string of 1 to 200 characters.
Description
Use the filename command to specify
a file to be transferred between the FPT server and the FTP client.
Use the undo filename command to
cancel the file.
By default, no file is specified.
Note that the filename command is
valid only for the FTP test.
Related command: username, password, and ftp-operation.
Example
# Specify the config.txt file to be
transferred between the FTP server and the FTP client.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
filename config.txt
Syntax
frequency
interval
undo frequency
View
NQA test group view
Parameter
interval:
Interval of performing a cyclic test in seconds, in the range of 1 to 65535.
Description
Use the frequency command to
configure the interval of performing a cyclic test. After you carry out the test-enable
command to start an NQA test, the test will be performed at intervals.
Use the undo frequency to restore
the default.
By default, no cyclic test is performed.
Note that the frequency command is
invalid for the DHCP test.
Related command: test-enable.
Example
# Configure the interval of performing a
cyclic test to 10 seconds.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
frequency 10
1.1.10 ftp-operation
Syntax
ftp-operation { get | put }
undo ftp-operation
View
NQA test group view
Parameter
get: Obtains
a file from the FTP server.
put:
Transfers a file to the FTP server.
Description
Use the ftp-operation command to
configure the FTP operation type.
Use the undo ftp-operation command
to restore the default FTP operation type.
By default, the FTP operation type is
“get” (obtain a file from the FTP server).
Note that the ftp-operation command
is valid only for FTP tests.
Related command: username and password.
Example
# Obtain a file from the FTP server.
[Sysname-nqa-administrator-test]
ftp-operation get
Syntax
history-records number
undo history-records
View
NQA test group view
Parameter
number:
Maximum number of history records that can be saved in a test group, in the
range of 0 to 50..
Description
Use the history-records command to
configure the maximum number of history records that can be saved in a test
group.
Use the undo history-records command
to restore the default.
By default, the maximum number of records
that can be saved in a test group is 50.
If the history records exceed the
predefined maximum number, the first test result will be discarded.
Example
# Configure the maximum number of history
records that can be saved in a test group to 10
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
history-records 10
1.1.12 http-operation
Syntax
http-operation { get | post }
undo http-operation
View
NQA test group view
Parameter
get: Obtains
data from the HTTP server.
post:
Transfers data to the HTTP server.
Description
Use the http-operation command to
configure the HTTP operation type.
Use the undo http-operation command
to restore the default HTTP operation type.
By default, the HTTP operation type is
“get” (obtain data from the HTTP server).
Note that the http-operation command
is valid only for HTTP tests.
Related command: http-string.
Example
# Obtain data from the HTTP server.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
http-operation get
1.1.13 http-string
Syntax
http-string string version
undo http-string
View
NQA test group view
Parameter
string: HTTP
operation string, which specifies a webpage to be accessed. The length of the string
argument plus that of the version argument cannot exceed 200 characters.
version:
HTTP version. Currently, it can only be “HTTP/1.0”, where HTTP must
be upper-case.
Description
Use the http-string command to
configure an HTTP operation string and version information.
Use the undo http-string command to
remove the configuration of the HTTP operation string and version information.
By default, no HTTP operation string or
version information is configured.
Note that the http-string command is
valid only for HTTP tests.
Related command: http-operation.
Example
# Set the web page accessible via HTTP to
/index.htm and the HTTP version to http/1.0.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
http-string /index.htm HTTP/1.0
Syntax
jitter-interval interval
undo jitter-interval
View
NQA test group view
Parameter
interval:
Interval for sending jitter test packets in milliseconds, in the range of 10 to
1,000.
Description
Use the jitter-interval command to
configure the interval of sending jitter test packets.
Use the undo jitter-interval command
to restore the default.
By default, the interval for sending jitter
test packets is 20 milliseconds.
Note that the jitter-interval
command is valid only for the jitter test.
Related command: jitter-packetnum.
Example
# Set the interval of sending jitter test
packets to 30 milliseconds.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
jitter-interval 30
Syntax
jitter-packetnum number
undo jitter-packetnum
View
NQA test group view
Parameter
number:
Number of test packets sent in a probe, in the range of 10 to 100.
Description
Use the jitter-packetnum command to
configure the number of jitter test packets sent in a probe.
Use the undo jitter-packetnum
command to restore the default.
By default, the number of test packets sent in
a probe is 10.
Note that the jitter-packetnum
command is valid only for the jitter test.
Related command: jitter-interval.
Example
# Set the number of packets sent in a probe
to 30.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
jitter-packetnum 30
Syntax
nqa admin-name
operation-tag
undo nqa
admin-name operation-tag
View
System view
Parameter
admin-name:
Name of the administrator who creates NQA test groups, a string of 1 to 32
characters.
operation-tag: Tag of a test operation, a string of 1 to 32 characters.
Description
Use the nqa command to create an NQA
test group and enter NQA test group view. If the test group already exists, you
will directly enter NQA test group view when you carry out the nqa
command.
Use the undo nqa command to
delete the test group.
Example
# Create an NQA test group whose administrator
name is “administrator” and whose operation tag is
“test” and enter NQA test group view.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
1.1.17 nqa-agent enable
Syntax
nqa-agent enable
undo nqa-agent enable
View
System view
Parameter
None
Description
Use the nqa-agent enable command to
enable the NQA client.
Use the undo nqa-agent enable
command to disable the NQA client.
By default, the NQA client is disabled.
Note that you can perform tests only after
the NQA client is enabled.
Related command: nqa-server enable.
Example
# Enable the NQA client.
<Sysname> system-view
[Sysname] nqa-agent enable
Syntax
nqa-agent max-requests max-number
undo nqa-agent max-requests
View
System view
Parameter
max-number:
Maximum number of tests that the NQA client can simultaneously perform, in the
range 1 to 5.
Description
Use the nqa-agent max-requests
command to configure the maximum number of tests that the NQA client can
simultaneously perform.
Use the undo nqa-agent max-requests
command to restore the default.
By default, the maximum number of tests
that the NQA client can simultaneously perform is five.
Example
# Specify the NQA client to simultaneously
perform four tests at most.
<Sysname> system-view
[Sysname] nqa-agent max-requests 4
1.1.19 password
Syntax
password password
undo password
View
NQA test group view
Parameter
password:
Password used to log in to the FTP server, a string of 1 to 32 characters.
Description
Use the password command to
configure a password used to log in to the FTP server.
Use the undo password command to
remove the password.
By default, no password is configured.
Note that the password command is
valid only for the FTP test.
Related command: username and ftp-operation.
Example
# Set the login password to nqa.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test] test-type
ftp
[Sysname-nqa-administrator-test]
username aaa
[Sysname-nqa-administrator-test]
password nqa
Syntax
probe-failtimes times
undo probe-failtimes
View
NQA test group view
Parameter
times:
Number of consecutive probe failures in a test, in the range of 1 to 15.
Description
Use the probe-failtimes command to configure
the number of consecutive probe failures in an NQA test before a trap message
is sent to the network management server to indicate a probe failure.
Use the undo probe-failtimes command
to restore the default.
By default, a Trap message is sent to the
network management (NM) server once a probe fails in an NQA test.
One test may
involve multiple probes.
Example
# Configure the system to send a Trap
message after three consecutive probe failures in an NQA test.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test] probe-failtimes
3
Syntax
sendpacket passroute
undo sendpacket passroute
View
NQA test group view
Parameter
None
Description
Use the sendpacket passroute command
to enable the routing table bypass function to test the direct connectivity to
the destination.
Use the undo sendpacket passroute
command to disable the routing table bypass function.
By default, the routing table bypass
function is disabled.
After this function is enabled, the routing
table is not searched, and the packet is directly sent to the destination in a
directly connected network. If the destination is not in the directly connected
network, an error will be prompted.
Note that the sendpacket passroute
command is invalid for DHCP tests.
Example
# Enable the routing table bypass function.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test] sendpacket
passroute
Syntax
send-trap { all
| { probefailure | testcomplete | testfailure }* }
undo send-trap { all | { probefailure | testcomplete | testfailure
}* }
View
NQA test group view
Parameter
probefailure: Sends a Trap message when a probe fails.
probecomplete: Sends a Trap message when a test is completed.
testfailure:
Sends a Trap message when a test fails (the number of probe failures in a test
is greater than or equal to the number configured by the test-failtimes
command). For a test, only one trap message is sent.
all: Sends a
Trap message in any of the above cases.
Description
Use the send-trap command to enable
the Trap debugging (A Trap message is sent to the network management server).
Use the undo send-trap command to
disable the Trap debugging (No Trap message is sent to the network management
server).
By default, no trap message is sent to the
network management server.
Example
# Send a Trap message when a test is
completed.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
send-trap testcomplete
1.1.23 source-interface
Syntax
source-interface interface-type interface-number
undo source-interface
View
NQA test group view
Parameter
interface-type interface-number: Specifies the interface by its type and number.
Description
Use the source-interface command to
specify the IP address of an interface as the source IP address of ICMP test
request packets or specify an interface for a DHCP test.
Use the undo source-interface
command to remove the configuration.
By default, no interface address is
specified as the source IP address of ICMP test request packets, or no
interface is specified for a DHCP test.
Note that:
l
For the DHCP test, the source-interface command
is required, for the ICMP test, it is optional, and for other tests, it is
invalid.
l
For an ICMP test, if a source IP address is
configured by using the source-ip command, the configuration by using
the source-interface command is invalid.
l
The interface specified by the source-interface
command can only be a layer 3 Ethernet interface or VLAN interface.
l
The interface specified by the command must be
up. Otherwise, the test will fail.
Example
# Specify Vlan-interface 3 for a DHCP test.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
source-interface Vlan-interface 3
Syntax
source-ip
ip-address
undo source-ip
View
NQA test group view
Parameter
ip-address:
Source IP address of a test request packet.
Description
Use the source-ip command to
configure a source IP address for a test request packet.
Use the undo source-ip command to
remove the configured source address. That is, the IP address of the interface
sending a test request packet serves as the source IP address of the test
request packet.
By default, no source IP address is
specified. If a source interface is specified, the IP address of the source
interface serves as the source IP address of a test request packet.
Note that:
l
For the FTP test, the source-ip command is
required, for the DHCP test, it is invalid, and for other tests, it is
optional.
l
The source IP address in the command must be the
IP address of an interface on the device and the interface must be up.
Otherwise, the test will fail.
Example
# Configure the source IP address of a test
request packet to 10.1.1.1.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
source-ip 10.1.1.1
Syntax
source-port port-number
undo source-port
View
NQA test group view
Parameter
port-number:
Source port number for a test request packet, in the range of 1 to 50000.
Description
Use the source-port command to
configure a source port number for a test request packet.
Use the undo source-port command to
remove the configured port number.
By default, no source port number is
specified.
Note that this command is only valid for
jitter, UDP, and SNMP tests.
Example
# Configure the source port number of a
test request packet to 8000.
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
source-port 8000
1.1.26 test-enable
Syntax
test-enable
undo test-enable
View
NQA test group view
Parameter
None
Description
Use the test-enable command to
enable the NQA test.
Use the undo test-enable command to
disable the NQA test.
Test results will not be displayed after
you enable the NQA test. In this case, you need to carry out the display nqa
command to display the test results.
Related command: display nqa.
Example
# Enable the NQA test.
<Sysname> system-view
[Sysname] nqa-agent enable
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
test-enable
Syntax
test-failtimes times
undo test-failtimes
View
NQA test group view
Parameter
times:
Minimum number of probe failures in a test before a Trap message is sent to
indicate a test failure, in the range of 1 to 15.
Description
Use the test-failtimes command to
configure the minimum number of probe failures in a test before a Trap message
is sent to the network management server to indicate a test failure.
Use the undo test-failtimes command
to restore the default.
By default, a Trap message is sent to the
NM server once a probe fails in a test.
One test may
involve multiple probes.
Example
# Configure the system to send a Trap
message to indicate a test failure after three probe failures in an NQA test
<Sysname> system-view
[Sysname] nqa administrator test
[Sysname-nqa-administrator-test]
test-failtimes 3
Syntax
test-type test-type
undo test-type
View
NQA test group view
Parameter
test-type:
Type of a test, including the following keywords:
l
dhcp: DHCP test
l
dlsw: DLSw test
l
ftp: FTP test
l
http: HTTP test
l
icmp: ICMP test
l
jitter: Analyzes and tests the delay jitter of
UDP packet transmission
l
snmpquery: SNMP test
