Throughout this
document, a filename can be entered as either of the following:
l
A fully qualified filename with the path
included to indicate a file under a specific path. The filename can be 1 to 135
characters in length.
l
A short filename with the path excluded to
indicate a file in the current working path. The filename can be 1 to 91
characters in length.
1.1.1 cd
Syntax
cd directory
View
User view
Parameter
directory:
Name of the target directory.
Description
Use the cd command to change the current
directory.
Example
# Change the current directory to flash:.
<Sysname> cd flash:
1.1.2 copy
Syntax
copy fileurl-source
fileurl-dest
View
User view
Parameter
fileurl-source:
Name of the source file.
fileurl-dest:
Name of the target file or directory.
Description
Use the copy command to copy a file.
If the name of the target file is the same
with the name of an existing file, the system asks whether to overwrite the
exiting one.
Example
# Copy file config.cfg and save it as tt.cfg.
<Sysname> copy config.cfg tt.cfg
Copy flash:/config.cfg to flash:/tt.cfg?[Y/N]:y
%Copy file flash:/config.cfg to
flash:/tt.cfg...Done.
1.1.3 delete
Syntax
delete [
/unreserved ] file-url
View
User view
Parameter
/unreserved: Permanently deletes the
specified file, and the deleted file can never be restored.
file-url:
Name of the file to be deleted including the path. Asterisks (*) are acceptable
as wildcards. For example, to remove files with the expansion of txt, you may
use the delete * command.
Description
Use the delete command to remove a
file from the storage device to the recycle bin, where you can restore the file
with the undelete command or permanently delete it with the reset
recycle-bin command.
The dir /all command displays the
files removed to the recycle bin. These files are enclosed in pairs of
brackets.
This command supports the wildcard *.
Caution:
If you delete two
files in different directories but with the same filename, only the last one is
retained in the recycle bin.
Example
# Remove file tt.cfg from the root
directory.
<Sysname> delete tt.cfg
Delete flash:/tt.cfg?[Y/N]:y
...
%Delete file flash:/tt.cfg...Done.
1.1.4 dir
Syntax
dir [ /all
| file-url ]
View
User view
Parameter
/all:
Displays all files (including those in the recycle bin).
file-url:
Name of the file or directory to be displayed. Asterisks (*) are acceptable as
wildcards. For example, to remove files with the .txt extension, you may use
the delete * command.
Description
Use the dir command to display
information about all visible files and folders in the current directory.
Use the dir /all command to display
information about all files and folders on your device, including hidden files,
hidden subfiles and those in the recycle bin. The names of these deleted files
are enclosed in pairs of brackets ([ ]).
The dir file-url command
displays information about a file or folder.
Example
# Display information about all files and
folders.
<Sysname> dir /all
Directory
of flash:/
0 -rw- 6985954 Apr 26 2005
21:06:29 mainup.bin
1 -rwh 1842 Apr 27 2005
04:37:17 private-data.txt
2 -rw- 1518 Apr 26 2005
12:05:38 config.cfg
3 -rw- 2045 May 04 2005
15:50:01 backcfg.cfg
4 -rwh 428 Apr 27 2005
16:41:21 hostkey
5 -rwh 572 Apr 27 2005
16:41:31 serverkey
6 -rw- 2737556 Oct 12 2005
01:31:44 [a.bin]
15240 KB total (5096 KB free)
1.1.5 execute
Syntax
execute filename
View
System view
Parameter
filename:
Name of a batch file with a .bat extension.
Description
Use the execute command to execute
the specified batch file.
Batch files are command line files.
Executing a batch file is to execute a set of command lines in the file.
You should not include invisible characters
in a batch file. If an invisible character is found during the execution, the batch
process will abort and the commands that have been executed cannot be cancelled.
Not every command in a batch file is sure to be executed. For example, if a
certain command is not correctly configured, the system omits this command and
goes to the next one. A batch file does not support hot backup. Each
configuration command in a batch file must be a standard configuration command,
meaning the valid configuration information which can be displayed with the display
current-configuration command after this command is configured
successfully; otherwise, this command may not be executed correctly.
Example
# Execute the batch file test.bat in the root
directory.
<Sysname> system-view
[Sysname] execute test.bat
Syntax
file prompt
{alert | quiet }
View
System view
Parameter
alert: Enables
the system to warn you about operations that may bring undesirable results such
as file corruption or data loss.
quiet: Disables
the system to warn you about any operation.
Description
Use the file prompt command to set a
prompt mode for file operations.
By default, the prompt mode is alert.
Note that when the prompt mode is set to
quiet, the system does not warn for any file operation. To prevent undesirable
consequents resulted from misoperations, the alert mode is preferred.
Example
# Set the file operation prompt mode to
alert.
<Sysname> system-view
[Sysname] file prompt alert
Syntax
fixdisk device
View
User view
Parameter
device:
Device name.
Description
Use the fixdisk command to restore
the space of a storage device when it becomes unavailable because of some
abnormal operation.
Example
# Restore the space of the Flash.
<Sysname> fixdisk flash:
Fixdisk flash: may take some time to
complete.
%Fixdisk flash: completed.
1.1.8 format
Syntax
format device
View
User view
Parameter
device:
Device name.
Description
Use the format command to format a
storage device.
Caution:
Formatting a device
results in loss of all the files and these files cannot be restored. In
particular, if you format the flash, the configuration file on it will be
removed.
Example
# Format the Flash.
<Sysname> format flash:
All data on flash: will be lost ,
proceed with format ? [Y/N]:y
./
%Format flash: completed.
1.1.9 mkdir
Syntax
mkdir directory
View
User view
Parameter
directory:
Name of subdirectory.
Description
Use the mkdir command to create a subdirectory
under the specified directory on the storage device.
The name of the subdirectory to be created
must be unique under the specified directory.
This command does not allow you to create
multiple directory levels at one time. For instance, to create a subdirectory “flash:/test/mytest”,
the test directory must have been created.
Example
# Create a directory named test.
<Sysname> mkdir ddtest
...
% Created dir flash:/ddtest
# create a subdirectory named mytest under
test.
<Sysname>mkdir test/mytest
...
%Created dir flash:/test/mytest
1.1.10 more
Syntax
more file-url
View
User view
Parameter
file-url:
File name.
Description
Use the more command to display the
contents of the specified file.
So far, this command displays the file in
the format of text.
Example
# Display the contents of file test.txt.
<Sysname> more test.txt
AppWizard has created this test
application for you.
This file contains a summary of what
you will find in each of the files that make up your test application.
Test.dsp
This file (the project file) contains
information at the project level and is used to build a single project or
subproject. Other users can share the project (.dsp) file, but they should
export the makefiles locally.
1.1.11 move
Syntax
move fileurl-source
fileurl-dest
View
User view
Parameter
fileurl-source:
Name of the source file.
fileurl-dest:
Name of the target file.
Description
Use the move command to move a file.
If the name of the target file is the same
as an existing one in the intended directory, the system will ask you whether
to overwrite the existing one.
Example
# Move the file flash:/test/sample.txt to
flash:/sample.txt.
<Sysname> move
flash:/test/sample.txt flash:/sample.txt
Move flash:/test/sample.txt to
flash:/sample.txt ?[Y/N]:y
% Moved file flash:/test/sample.txt
to flash:/sample.txt
Syntax
pwd
View
User view
Parameter
None
Description
Use the pwd command to display the
current path.
If the current path is not set, the
operation will fail.
Example
# Display the current path.
<Sysname> pwd
flash:
Syntax
rename fileurl-source
fileurl-dest
View
User view
Parameter
fileurl-source:
Name of the source file or directory.
fileurl-dest:
Name of the target file or directory.
Description
Use the rename command to rename a
file or directory.
The target file name must be unique under
the current path.
Example
# Rename the file sample.txt to sample.bak.
<Sysname> rename sample.txt sample.bak
Rename flash:/sample.txt to flash:/sample.bak?[Y/N]:y
%Renamed file flash:/sample.txt to
flash:/sample.bak.
1.1.14 reset recycle-bin
Syntax
reset recycle-bin [ file-url ] [ /force ]
View
User view
Parameter
file-url:
Name of the file to be deleted. This argument accepts asterisks (*) as
wildcards. For example, you may perform reset recycle-bin *.txt to
delete all files with the .txt extension from the recycle bin.
/force:
Empties the recycle bin.
Description
Use the reset recycle-bin command to
permanently remove deleted file or files from the recycle bin.
Unlike this command, the delete file-url
command only moves files to the recycle bin.
Example
# Empty the recycle bin.
<Sysname> reset recycle-bin
Clear flash:/~/tt.cfg ?[Y/N]:y
Clearing files from flash may take a
long time. Please wait...
...
%Cleared file flash:/~/tt.cfg...
Syntax
rmdir directory
View
User view
Parameter
directory:
Name of the directory.
Description
Use the rmdir command to remove a
directory.
The directory must be an empty one. If it
is not, first delete all files and subdirectories under it with the delete
command.
Example
# Remove directory mydir.
<Sysname> rmdir mydir
Rmdir flash:/mydir?[Y/N]:y
.
%Removed directory flash:/mydir.
1.1.16 undelete
Syntax
undelete file-url
View
User view
Parameter
filename:
Name of the file to be restored.
Description
Use the undelete command to restore
a file from the recycle bin.
If another file with the same name has
already existed under the same path, the undelete operation will cause it to be
overwritten and the system will ask you whether to continue.
Example
# Restore file sample.bak from the recycle
bin.
<Sysname> undelete sample.bak
Undelete flash:/sample.bak ?[Y/N]:y
%Undeleted file flash:/sample.bak.
1.2.1 backup startup-configuration
Syntax
backup startup-configuration to dest-addr [ dest-filename ]
View
Use view
Parameter
dest-addrIP address or name of a TFTP server. The address cannot be an IPv6
address.
dest-filename: Filename used to save the next startup configuration file on the
server.
Description
Use the backup startup-configuration command
to backup the main startup configuration file (for next startup) using a
filename you specify. If you do not specify this filename, the original
filename will be used.
Presently, the device uses TFTP to implement
backup operation.
Example
# Backup the main configuration
file for next startup on the TFTP server with IP address 2.2..2.2, using the
filename config.cfg.
<Sysname> backup
startup-configuration to 2.2.2.2 config.cfg
Backup next startup-configuration
file to 2.2.2.2, please wait…
finished!
<Sysname>
1.2.2 display saved-configuration
Syntax
display saved-configuration [ by-linenum ]
View
Any view
Parameter
by-linenum: Identifies
each line of displayed information with a line number.
Description
Use the display saved-configuration
command to display the configuration file saved in the storage device.
In case the device malfunctions after being
powered up, you may use this command to identify the problem.
If you do not use the configuration file
when the device starts up, no startup configuration file information is
displayed after you execute the display startup command, and no
information is displayed when you execute the display saved-configuration
command; if you have saved the configuration file after the device starts up,
the information saved in the configuration file the last time is displayed.
Related command: save, reset
saved-configuration, and the display current-configuration command
in Basic System Configuration and Maintenance Command Module.
Example
# Display the
configuration file saved in the Flash.
<Sysname>display
saved-configuration
#
sysname Sysname
#
domain default enable system
#
telnet server enable
#
vlan 1
#
vlan 3000
#
radius scheme system
server-type extended
primary authentication 127.0.0.1
1645
primary accounting 127.0.0.1 1646
user-name-format without-domain
#
domain system
access-limit disable
state active
idle-cut disable
self-service-url disable
#
acl number 2000
rule 0 deny
#
acl number 3000
rule 0 permit ip
#
acl number 4000
#
acl ipv6 number 2000
rule 0 permit source 2001::2/64
#
interface NULL0
#
interface LoopBack0
#
interface Vlan-interface1
ip address 192.168.0.52 255.255.0.0
#
interface Vlan-interface3000
ip address 30.1.1.1 255.255.255.0
#
interface GigabitEthernet1/0/1
#
interface GigabitEthernet1/0/2
#
interface GigabitEthernet1/0/3
#
interface GigabitEthernet1/0/4
#
interface GigabitEthernet1/0/5
#
interface GigabitEthernet1/0/6
#
interface GigabitEthernet1/0/7
#
interface GigabitEthernet1/0/8
#
interface GigabitEthernet1/0/9
#
interface GigabitEthernet1/0/10
#
interface GigabitEthernet1/0/11
#
interface GigabitEthernet1/0/12
#
interface GigabitEthernet1/0/13
#
interface GigabitEthernet1/0/14
#
interface GigabitEthernet1/0/15
#
interface GigabitEthernet1/0/16
#
interface GigabitEthernet1/0/17
#
interface GigabitEthernet1/0/18
#
interface GigabitEthernet1/0/19
#
interface GigabitEthernet1/0/20
#
interface GigabitEthernet1/0/21
#
interface GigabitEthernet1/0/22
#
interface GigabitEthernet1/0/23
#
interface GigabitEthernet1/0/24
#
interface GigabitEthernet1/0/25
shutdown
#
interface GigabitEthernet1/0/26
shutdown
#
interface GigabitEthernet1/0/27
shutdown
#
interface GigabitEthernet1/0/28
shutdown
#
user-interface aux 0
user-interface vty 0 4
authentication-mode none
user privilege level 3
#
return
The configurations are displayed in the
order of global, port, and user interface.
1.2.3
display startup
Syntax
display startup
View
User view
Parameter
None
Description
Use the display startup command to
display the configuration file used at this startup and the one used for next
startup.
Related command: startup
saved-configuration.
Example
# Display the configuration file used at
this startup and the one used for next startup
<Sysname> display startup
Current startup saved-configuration
file: flash:/config.cfg
Next main startup
saved-configuration file: flash:/config.cfg
Next backup startup
saved-configuration file: NULL
1.2.4 reset saved-configuration
Syntax
reset saved-configuration [ main | backup ]
View
User view
Parameter
main: Erases
the main configuration file.
backup: Erases
the backup configuration file.
Description
Use the reset saved-configuration
command to erase the configuration file saved in the
storage device.
If you do not specify the main/backup
parameter, you will erase, by default, the main configuration file.
Caution:
This command will
permanently delete the configuration file on the device.
In case no configuration file is available,
the device starts up with the default settings.
Related command: save, display
saved-configuration.
Example
# Erase the configuration file saved in the
storage device.
<Sysname> reset
saved-configuration backup
The saved configuration will be
erased.
Are you sure? [Y/N]:y
Configuration in the device is being
cleared.
Please wait .......
Configuration in the device is
cleared.
1.2.5 restore startup-configuration
Syntax
restore startup-configuration from src-addr src-filename
View
Use view
Parameter
src-addr: IP
address or name of a TFTP server. The address cannot be an IPv6 address.
src-filename:
Filename of the configuration file to be downloaded from the specified server.
Description
Use the restore startup-configuration command
to download the configuration file from the specified TFTP server as the main
configuration file for the next startup of the device.
If the file to be downloaded has the same
filename as an existing file on the device, you will be prompted whether you
want to overwrite the existing file or not.
Example
# Download the configuration file config.cfg
for the next startup from the TFTP server whose IP address is .2.2.2.2.
<Sysname>restore
startup-configuration from 2.2.2.2 config.cfg
Restore next startup-configuration
file from 2.2.2.2. Please wait........
finished!
1.2.6 save
Syntax
save [ file-name
| [ safely ] [ main | backup ] ]
View
Any view
Parameter
file-name:
File name, whose extension must be .cfg.
safely: Sets
the configuration saving mode to safe. Executing the command without the safely
keyword is fast, but the file cannot survive a reboot or power-off during
saving operation.
main: Save
the configuration as the main configuration file.
backup: Save
the configuration as the backup configuration file.
Description
Use the save command to save the current configuration to the specified
file, or if no filename is specified, to the default file at the root directory.
l
The command saves the current configuration to
the main configuration file if the main or backup parameters are not specified.
l
If you specified a filename, but the filename
does not exist, the system will create this file and save the configuration
into this file. The file attribute is neither main or backup.
l
If you specified a filename and this file
exists, the system will save the configuration into this file. The file attribute
is the original attribute of the file.
Related command: reset
saved-configuration, display current-configuration, display
saved-configuration.
Example
# Save the current configuration to the
file named test.cfg
<Sysname> save test.cfg
The current configuration will be saved
to flash:/test.cfg [Y/N]:Y
Now saving current configuration to
the device.
Saving configuration flash:/test.cfg.
Please wait...
......
Configuration is saved to flash
successfully.
<Sysname>
# Save the current configuration to the
backup configuration file
<Sysname> save backup
The current configuration will be
written to the device.
Are you sure?[Y/N]:Y
Please input the file name(*.cfg)[flash:/backup.cfg](To
leave the
existing filename unchanged, press
the enter key):test.cfg
Validating file. Please wait...
Now saving current configuration to
the device.
Saving configuration flash:/test.cfg.
Please wait...
..
Configuration is saved to flash
successfully.
<Sysname>
1.2.7 startup saved-configuration
Syntax
startup saved-configuration
cfgfile [ main | backup
]
undo startup saved-configuration
View
User view
Parameter
cfgfile:
Configuration file name.
main: Sets
the configuration file as main configuration file.
backup: Sets
the configuration file as backup configuration file.
Description
Use the startup saved-configuration
command to specify a configuration file for next startup.
Use the undo startup saved-configuration
command to start up with an empty configuration, which means startup with the
initial configuration of the system.
This command erases the attribute but
without deleting the file.
The specified file must be ended with a .cfg
extension and saved in the root directory of the storage device.
The follow cases exist when using this
command to specify a configuration file for next startup:
l
With a normal configuration file, after
executing the startup saved-configuration cfgfile main command,
the configuration file becomes a main configuration file.
l
With a normal configuration file, after
executing the startup saved-configuration cfgfile backup command,
the configuration file becomes a backup configuration file.
l
With a main configuration file, after executing
the startup saved-configuration cfgfile backup command,
the configuration file has both main and backup attributes.
l
With a backup configuration file, after
executing the startup saved-configuration cfgfile main command,
the configuration file has both main and backup attributes.
l
If main/backup attribute is not specified, the file
is set as a configuration file.
l
If a main configuration file already exists when
setting a new file as the main configuration file, the main attribute of the
existing file will be erased to allow only one main configuration file in the
system.
l
If a main configuration file already exists when
setting a new file as the backup configuration file, the backup attribute of
the existing file will be erased to allow only one backup configuration file in
the system.
Related command: display startup.
Example
# Specify a backup configuration file for
next startup.
<Sysname> startup saved-configuration
config.cfg backup
Please wait......Done!
Chapter 2 FTP
Configuration Commands
Syntax
display ftp-server
View
Any view
Parameter
None
Description
Use the display ftp-server command to
display the FTP server configuration of the device.
After configuring FTP parameters, you may verify
them with this command.
Example
# Display the FTP server configuration.
<Sysname> display ftp-server
FTP server is running
Max user number: 1
User count 1
Timeout value(in minute) ):
30
Put Method :
fast
The output indicates that the FTP server is
running with support to only one login user; now one logged-in user is present;
timeout of the user is 30 minutes, and FTP put mode is fast.
Syntax
display ftp-user
View
Any view
Parameter
None
Description
Use the display ftp-user command to
display the parameter settings of current FTP users.
Example
# Display the parameter settings of FTP
users.
<Sysname> display ftp-user
UserName HostIP
Port Idle HomeDir
user1 10.110.3.5
2804 1 flash:/user1
2.1.3 ftp server enable
Syntax
ftp server enable
undo ftp server
View
System view
Parameter
None
Description
Use the ftp server enable command to
enable the FTP server.
Use the undo ftp server command to
disable the FTP server.
By default, the FTP server is disabled to
prevent attacks.
Example
# Disable the FTP server.
<Sysname>system-view
[Sysname] undo ftp server
% Close FTP server
2.1.4 ftp timeout
Syntax
ftp timeout minute
undo ftp timeout
View
System view
Parameter
minute:
Idle-timeout timer in minutes, in the range 1 to 35791. The default is 30
minutes.
Description
Use the ftp timeout command to set
the idle-timeout timer.
Use the undo ftp timeout command to
restore the default.
After you log onto the FTP server, you set
up an FTP connection. When the connection is disrupted or aborted, the FTP
server, if not notified, cannot realize that and maintains the connection all
the same. To address this problem, you can set an idle-timeout timer to have
the FTP server disconnect if no command is received or/and transmitted before
the timer expires.
Example
# Set the idle-timeout timer to 36 minutes.
<Sysname> system-view
[Sysname] ftp timeout 36
2.1.5 ftp update
Syntax
ftp update {
fast | normal }
undo ftp update
View
System view
Parameter
fast: Fast
update.
normal:
Normal update.
Description
Use the ftp update command to set
the file update mode that the FTP server uses while receiving data.
Use the undo ftp update command to
restore the default, namely, the normal mode.
The FTP server has two modes to update files
when you upload files (use the put command) to the FTP server:
l
Fast update mode, that is, the FTP server first
receives all the uploaded files to the memory, and then writes the files into
the Flash memory of the device. In this mode, even if exceptional situations such
as power failure occur on the FTP client during the file transfer process, the
files on the FTP server will not be corrupted.
l
Normal update mode, that is, the FTP server
writes the uploaded files to the Flash memory of the device while receiving the
files. In this mode, the files on the server may be corrupted if exceptional situations
such as power failure occur. However, compared with the fast update mode, this
mode needs less free memory.
Example
# Set the FTP update mode to fast.
<Sysname> system-view
[Sysname] ftp update fast
2.2 FTP Client Configuration Commands
l
You must use the ftp command to enter the
FTP client view for configurations under this view. For details, refer to 2.2.10 ftp.
l
The prompt information in the examples of this
section depends on your FTP server type.
Syntax
ascii
View
FTP client view
Parameter
None
Description
Use the ascii command to set the file transfer mode to ASCII for the FTP connection.
FTP provides two file transfer modes: ASCII
and binary. To transfer text files, use the ASCII mode; to transfer program
files, use the binary mode.
By default, the file transfer mode is
ASCII.
Example
# Set the file transfer mode to ASCII.
[ftp] ascii
200 Type set to A.
2.2.2 binary
Syntax
binary
View
FTP client view
Parameter
None
Description
Use the binary command to set the file transfer mode to binary (also called flow mode).
FTP uses two modes to transfer files, one
is binary mode, which is used to transfer program file; the other is ASCII
mode, which is used to transfer text files.
By default, the transfer mode is ASCII
mode.
Example
# Set the file transfer mode to binary.
[ftp] binary
200 Type set to I.
2.2.3 bye
Syntax
bye
View
FTP client view
Parameter
None
Description
Use the bye command to disconnect from the remote FTP server and exit to user view.
Example
# Terminate the connection with the remote
FTP server and exit to user view.
[ftp] bye
221 Server closing.
<Sysname>
Syntax
cd pathname
View
FTP client view
Parameter
pathname:
Path name.
Description
Use the cd command to change the current working directory path on the remote FTP server.
You can use this command to access another authorized
directory on the FTP server.
Example
# Change the current working directory path
to flash:/temp.
[ftp] cd flash:/temp
250 CWD command successful.
Syntax
cdup
View
FTP client view
Parameter
None
Description
Use the cdup command to exit the current directory and enter the upper directory of the FTP server.
Example
# Change the current working directory path
to the upper directory.
[ftp] cdup
200 CDUP command successful.
2.2.6 close
Syntax
close
View
FTP client view
Parameter
None
Description
Use the close command to terminate the connection to the FTP server, but remain in FTP client
view.
This command is equal to the disconnect
command.
Example
# Terminate the
connection to the FTP server and remain in FTP client view.
[ftp] close
221 Server closing.
[ftp]
2.2.7 delete
Syntax
delete remotefile
View
FTP client view
Parameter
remotefile:
File name.
Description
Use the delete command to delete a file on the remote FTP server.
To do this, you must be a user with the
delete permission on the FTP server.
Example
# Delete file temp.c.
[ftp] delete temp.c
250 DELE command successful.
Syntax
dir [ remotefile
[ localfile ] ]
View
FTP client view
Parameter
remotefile:
Name of the file or directory on the remote FTP server.
localfile:
Name of the local file to save the displayed information.
Description
Use the dir command to view detailed
information of the files and subdirectories under the current directory on the remote
FTP server.
Use the dir remotefile command
to display the detailed information of the specified
file or directory on the remote FTP server.
Use the dir remotefile localfile command to display the detailed information
of the specified file or directory on the remote FTP server, and save the displayed information into a local file specified by the
localfile.argument.
The Is
command can only display the names of files and directories, whereas the dir
command can display other extra information of the files and directories,
such as the size, the date they are created.
Example
# View the information of the file ar-router.cfg,
and save the result to aa.txt.
[ftp] dir ar-router.cfg aa.txt
227 Entering Passive Mode
(192,168,1,50,17,158).
125 ASCII mode data connection
already open, transfer starting for config.cfg.
....226 Transfer complete.
FTP: 67 byte(s) received in 4.600
second(s), 14.00 byte(s)/sec.
# View the content of aa.txt
[ftp] quit
<Sysname> more aa.txt
-rwxrwxrwx 1 noone nogroup
3077 Jun 20 15:34 ar-router.cfg
