As shown in the following figure, the S3100-26T-SI
Ethernet Switch provides 24 x 10/100Base-TX Ethernet ports, two 10/100/1000Base-T
Ethernet ports, and one Console port.
Figure 1-1 S3100-26T-SI Ethernet Switch
The following figure shows the front panel
of the S3100-26T-SI Ethernet Switch.
|
(1) Power LED
|
(2) A/L mode LED
|
|
(3) D/S mode LED
|
(4) Port left LED (yellow)
|
|
(5) Port right LED (green)
|
(6) 10/100 Base-TX
port
|
|
(7) 10/100/1000 Base-T port
|
(8) Console port
|
|
(9) Link LED (green)
|
(10) Active LED (yellow)
|
|
(11) Mode switch
button
|
|
Figure 1-2 Front panel of the S3100-26T-SI
Ethernet Switch
The following figure shows the rear panel
of the S3100-26T-SI Ethernet Switch.
|
(1) AC power socket
|
(2) Grounding screw
|
Figure 1-3 Rear panel of the S3100-26T-SI
Ethernet Switch
The S3100-26T-SI Ethernet Switch supports
AC input power module.
l
Rated voltage range: 100 VAC to 240 VAC, 50/60
Hz
l
Max voltage range: 90 VAC to 264 VAC, 47 Hz to
63 Hz
The S3100-SI Series Ethernet Switches
(hereinafter referred to as S3100-SI series) cool off in nature way.
As shown in the following figure, the S3100-16T-SI
Ethernet Switch provides 16 x 10/100Base-TX Ethernet ports, one 10/100/1000Base-T
Ethernet port, and one Console port.
Figure 1-4 S3100-16T-SI Ethernet Switch
The following figure shows the front panel
of the S3100-16T-SI Ethernet Switch.
|
(1) Power LED
|
(2) A/L mode LED
|
|
(3) D/S mode LED
|
(4) Port left LED (yellow)
|
|
(5) Port right LED (green)
|
(6) 10/100 Base-TX
port
|
|
(7) 10/100/1000 Base-T port
|
(8) Console port
|
|
(9) Link LED (green)
|
(10) Active LED (yellow)
|
|
(11) Mode switch
button
|
|
Figure 1-5 Front panel of the S3100-16T-SI
Ethernet Switch
The following figure shows the rear panel
of the S3100-16T-SI Ethernet Switch.
|
(1) AC power socket
|
(2) Grounding screw
|
Figure 1-6 Rear panel of the S3100-16T-SI
Ethernet Switch
The S3100-16T-SI Ethernet Switch supports
AC input power module.
l
Rated voltage range: 100 VAC to 240 VAC, 50/60
Hz
l
Max voltage range: 90 VAC to 264 VAC, 47 Hz to 63
Hz
The S3100-SI series cool off in nature way.
As shown in the following figure, the S3100-8T-SI
Ethernet Switch provides 8 x 10/100Base-TX Ethernet ports, one 10/100/1000Base-T
Ethernet port, and one Console port.
Figure 1-7 S3100-8T-SI Ethernet Switch
The following figure shows the front panel
of the S3100-8T-SI Ethernet Switch.
|
(1) Power LED
|
(2) A/L mode LED
|
|
(3) D/S mode LED
|
(4) Port left LED (yellow)
|
|
(5) Port right LED (green)
|
(6) 10/100 Base-TX
port
|
|
(7) 10/100/1000 Base-T port
|
(8) Console port
|
|
(9) Link LED (green)
|
(10) Active LED (yellow)
|
|
(11) Mode switch
button
|
|
Figure 1-8 Front panel of the S3100-8T-SI
Ethernet Switch
The following figure shows the rear panel
of the S3100-8T-SI Ethernet Switch.
|
(1) AC power socket
|
(2) Grounding screw
|
Figure 1-9 Rear panel of the S3100-8T-SI
Ethernet Switch
The S3100-8T-SI Ethernet Switch supports AC
input power module.
l
Rated voltage range: 100 VAC to 240 VAC, 50/60
Hz
l
Max voltage range: 90 VAC to 264 VAC, 47 Hz to
63 Hz
The S3100-SI series cool off in nature way.
As shown in the following figure, the S3100-26C-SI/S3100-26C-SI-DC
Ethernet Switch provides 24 x 10/100Base-TX Ethernet ports, two expansion
slots, and one Console port.
Figure 1-10 S3100-26C-SI/S3100-26C-SI-DC
Ethernet Switch
S3100-26C-SI and S3100-26C-SI-DC Ethernet
Switch have the same front panel, as shown in Figure
1-11.
|
(1) Power LED
|
(2) A/L mode LED
|
|
(3) D/S mode LED
|
(4) Port left LED (yellow)
|
|
(5) Port right LED (green)
|
(6) 10/100 BASE-TX port
|
|
(7) Expansion slot
|
(8) Console port
|
|
(9) Mode switch button
|
|
Figure 1-11 Front panel of the S3100-26C-SI/S3100-26C-SI-DC Ethernet Switch
The S3100-26C-SI Ethernet Switch has two
models: one supports AC input, and another supports DC input.
I. Rear panel of the S3100-26C-SI
model supporting AC input:
|
(1) AC power socket
|
(2) Grounding screw
|
Figure 1-12 Rear panel of the S3100-26C-SI
model supporting AC input
II. Rear panel of the S3100-26C-SI
model supporting DC input:
|
(1) DC power socket
|
(2) Grounding screw
|
Figure 1-13 Rear panel of the S3100-26C-SI-DC
model supporting DC input
I. AC input:
l
Rated voltage range: 100 VAC to 240 VAC, 50/60 Hz
l
Max voltage range: 90 VAC to 264 VAC, 47 Hz to 63
Hz
II. DC input:
l
Rated voltage range: –48 VDC to –60 VDC
l
Max voltage range: –36 VDC to –72 VDC
The S3100-SI series cool off in nature way.
As shown in the following figure, the S3100-16C-SI/S3100-16C-SI-DC
Ethernet Switch provides 16 x 10/100Base-TX Ethernet ports, two expansion
slots, and one Console port.
Figure 1-14 S3100-16C-SI/S3100-16C-SI-DC
Ethernet Switch
S3100-16C-SI and S3100-16C-SI-DC Ethernet
Switch have the same front panel, as shown in Figure
1-15.
|
(1) Power LED
|
(2) A/L mode LED
|
|
(3) D/S mode LED
|
(4) Port left LED (yellow)
|
|
(5) Port right LED (green)
|
(6) 10/100 BASE-TX port
|
|
(7) Expansion slot
|
(8) Console port
|
|
(9) Mode switch button
|
|
Figure 1-15 Front panel of the S3100-16C-SI/S3100-16C-SI-DC Ethernet Switch
l
When a PoE card is inserted in one of the
expansion slots of the S3100-16C-SI/S3100-16C-SI-DC Ethernet Switch, the switch
becomes a powered device. In this case, the other expansion slot cannot be
used.
l
For details about the LEDs on the front panel,
refer to section 1.7 S3100-SI Series Front Panel LEDs.
The S3100-16C-SI Ethernet Switch has two
models: one supports AC input, and another supports DC input.
I. Rear panel of the S3100-16C-SI
model supporting AC input:
|
(1) AC power socket
|
(2) Grounding screw
|
Figure 1-16 Rear panel of the S3100-16C-SI
model supporting AC input
II. Rear panel of the S3100-16C-SI
model supporting DC input:
|
(1) DC power socket
|
(2) Grounding screw
|
Figure 1-17 Rear panel of the S3100-16C-SI-DC
model supporting DC input
I. AC input:
l
Rated voltage range: 100 VAC to 240 VAC, 50/60 Hz
l
Max voltage range: 90 VAC to 264 VAC, 47 Hz to 63
Hz
II. DC input:
l
Rated voltage range: –48 VDC to –60 VDC
l
Max voltage range: –36 VDC to –72 VDC
The S3100-SI series cool off in nature way.
As shown in the following figure, the S3100-8C-SI/S3100-8C-SI-DC
Ethernet Switch provides 8 x 10/100Base-TX Ethernet ports, one expansion slot,
and one Console port.
Figure 1-18 S3100-8C-SI/S3100-8C-SI-DC
Ethernet Switch
S3100-16C-SI and S3100-16C-SI-DC Ethernet
Switch have the same front panel, as shown in Figure
1-19
|
(1) Power LED
|
(2) A/L mode LED
|
|
(3) D/S mode LED
|
(4) Port left LED (yellow)
|
|
(5) Port right LED (green)
|
(6) 10/100 BASE-TX port
|
|
(7) Expansion slot
|
(8) Console port
|
|
(9) Mode switch button
|
|
Figure 1-19 Front panel of the S3100-8C-SI/S3100-8C-SI-DC Ethernet Switch
The S3100-8C-SI Ethernet Switch has two models:
one supports AC input, and another supports DC input.
I. Rear panel of the S3100-8C-SI
model supporting AC input:
|
(1) AC power socket
|
(2) Grounding screw
|
Figure 1-20 Rear panel of the S3100-8C-SI
model supporting AC input
II. Rear panel of the S3100-8C-SI
model supporting DC input:
|
(1) DC power socket
|
(2) Grounding screw
|
Figure 1-21 Rear panel of the S3100-8C-SI-DC
model supporting DC input
I. AC input:
l
Rated voltage range: 100 VAC to 240 VAC, 50/60 Hz
l
Max voltage range: 90 VAC to 264 VAC, 47 Hz to 63
Hz
II. DC input:
l
Rated voltage range: –48 VDC to –60 VDC
l
Max voltage range: –36 VDC to –72 VDC
The S3100-SI series cool off in nature way.
1.7 S3100-SI
Series Front Panel LEDs
Table 1-1 Description of the power LED
on S3100-SI series
|
LED
|
Mark on the panel
|
Status
|
Description
|
|
Power LED
|
PWR
|
ON
|
The switch is powered on.
|
|
OFF
|
The switch is powered off.
|
The A/L mode LED and the D/S mode LED are
used to indicate the mode of the port status LEDs. Only one of the two mode
LEDs is on at one time. When the A/L mode LED is on, it implies that the port
status LEDs are indicating the Active and Link status of the corresponding
ports. When the D/S mode LED is on, it implies that the port status LEDs are
indicating the Duplex and Speed status of the corresponding ports.
Table 1-2 Description of the port status
LEDs on the S3100-SI series
|
Mode LED status
|
Port status LEDs and their status
|
Description
|
|
A/L mode LED is on
|
Yellow LED (left)
|
Flashing
|
Data is passing through the port.
|
|
OFF
|
No data is passing through the port.
|
|
Green LED (right)
|
ON
|
The port is connected properly
|
|
OFF
|
The port is not connected or wrongly
connected.
|
|
D/L mode
LED is on
|
Yellow LED
(left)
|
ON
|
The port
operates in full duplex mode.
|
|
OFF
|
The port
operates in half duplex mode.
|
|
Green LED
(right)
|
ON
|
The port
operates at 100 Mbps.
|
|
OFF
|
The port
operates at 10 Mbps.
|
The MODE button is a mode switch button for
the status LEDs of 100 Mbps Ethernet ports. You can toggle between the A/L LED
and the D/S LED by pressing this button.
After the switch is powered on, the A/L LED
lights up initially. If you press the MODE button, the D/S LED lights up. After
that, if you press the MODE button again within 45 seconds, the A/L LED lights
up again, or else the A/L LED automatically lights up after 45 seconds.
The MODE button is convenient for you to
check the current status of the ports as required. For example, if you want to
learn the Duplex and the Speed status of a port, you can first press the MODE
button to switch to the D/S LED, then observe the status (OFF, ON, or flashing)
of the two LEDs beside the port, and finally determine the current status of
the port according to the above table.
Table 1-3 S3100-26T-SI/S3100-16T-SI/S3100-8T-SI
technical specifications
|
Item
|
S3100-26T-SI
|
S3100-16T-SI
|
S3100-8T-SI
|
|
Physical dimensions (H x W x D)
|
42 x 436 x 240 mm (1.7 x 17.2 x 9.4 in)
|
42 x 436 x 200 mm (1.7 x 17.2 x 7.9 in)
|
42 x 326 x 200 mm (1.7 x 12.8 x 7.9 in)
|
|
Weight
|
≤ 3.2 kg (7.1 lb)
|
|
Number of fixed ports
|
24 x 10/100Base-TX auto-sensing ports
2 x 10/100/1000Base-T ports
|
16 x 10/100Base-TX auto-sensing ports
1 x 10/100/1000Base-T port
|
8 x 10/100Base-TX auto-sensing ports
1 x 10/100/1000Base-T port
|
|
Management port
|
One Console port
|
|
Power supply
|
Only AC input is supported.
Rated voltage range: 100 VAC to 240 VAC, 50/60
Hz
Max voltage range: 90 VAC to 264 VAC, 47 Hz
to 63 Hz
|
|
PoE (as powered device)
|
Not supported
|
Not supported
|
Not supported
|
|
System power consumption (full load)
|
20 W
|
12 W
|
10 W
|
|
Fan
|
None
|
None
|
None
|
|
Operating temperature
|
0°C to 45°C
|
|
Relative humidity (noncondensing)
|
10% to 90%
|
Table 1-4 S3100-26C-SI/S3100-16C-SI/S3100-8C-SI
technical specifications
|
Item
|
S3100-26C-SI
|
S3100-16C-SI
|
S3100-8C-SI
|
|
Physical dimension (H x W x D)
|
42 x 436 x 240 mm (1.7 x 17.2 x 9.4 in)
|
42 x 436 x 200 mm (1.7 x 17.2 x 7.9 in)
|
42 x 326 x 200 mm (1.7 x 12.8 x 7.9 in)
|
|
Weight
|
≤ 3.2 kg (7.1 lb)
|
|
Number of fixed ports
|
24 x 10/100Base-TX auto-sensing ports
|
16 x 10/100Base-TX auto-sensing ports
|
8 x 10/100Base-TX auto-sensing ports
|
|
Number of expansion slots
|
2
|
2
|
1
|
|
Supported expansion interface module type
|
10/100/1000BASE-T interface module with
max transmission distance of 100 m (328.1 feet)
100BASE-SX (SC, 2 km (1.2 mi))
100BASE-LX (SC, 15 km (9.3 mi))
100BASE-LH40 (SC, 40 km (24.9 mi))
1000BASE-SX (SC, 0.5 km (0.3 mi))
1000BASE-LX (SC, 10 km (6.2 mi))
1000BASE-LH40 (LC, 40 km (24.9 mi))
1000BASE-LH70 (LC, 70 km (43.5 mi))
1000BASE-STACK (not supported by S3100-8C-SI)
100BASE-TX PD (powered device) interface
module (not supported by S3100-26C-SI)
1000Base-PX10 (SC connector, 10 km (6.2 mi))
1000Base-PX20 (SC connector, 20 km (12.4mi))
100Base-LX-SM1310-BIDI (SC, 15 km (9.3 mi))
100Base-LX-SM1550-BIDI (SC, 15 km (9.3 mi))
|
|
Management port
|
One Console port
|
|
Power supply
|
Both AC input switch model and DC input
switch model are available.
AC input:
Rated voltage range: 100 VAC to 240 VAC, 50/60Hz
Max voltage range: 90 VAC to 264 VAC, 47 Hz
to 63 Hz
DC input:
Rated voltage range: –48 VDC to –60 VDC
Max voltage range: –36 VDC to –72 VDC
|
|
PoE (as powered device)
|
Not supported
|
Supported
|
Supported
|
|
System power consumption (full load)
|
20 W
|
12 W
|
10 W
|
|
Fan
|
None
|
None
|
None
|
|
Operating temperature
|
0°C to 45°C
|
|
Relative humidity (noncondensing)
|
10% to 90%
|
l
Only S3100-16C-SI or S3100-8C-SI switch supports
100BASE-TX PD interface module.
l
The PoE configuration is on the remote power
source device, on the powered device (S3100-16C-SI or S3100-8C-SI), you only
need to insert the cable into the interface of 100BASE-TX PD.
l
BIDI interface card must used in couple, i.e.,
if the local end uses 100Base-LX-SM1310-BIDI, the remote end need to use
100Base-LX-SM1550-BIDI.
l
An S3116C or S3126C switch can accommodate only
one ONU card (000Base-PX10/20)
To avoid any device impairment and bodily
injury because of improper use, please take the following precautions:
l
Before cleaning the switch, pull out the power
plug of the switch. Do not clean the switch with wet cloth or liquid.
l
Do not place the switch near water or in a damp
area. Prevent water or moisture from entering the switch chassis.
l
Do not place the switch on an unstable case or
desk, because the switch might be damaged severely in case of a fall.
l
Keep the switch room drafty and the switch
ventilation hole free of obstruction.
l
The switch can operate normally only under
correct voltage input. Make sure that the operating voltage is consistent with
that labeled on the switch.
l
To prevent electric shock, do not open the
chassis while the switch is operating, and do not open the chassis arbitrarily even
when the switch is powered off.
l
Before changing interface board, wear
ESD-preventive wrist strap to prevent the board from being damaged by electrostatic
discharge.
S3100-SI series must be used indoors. When
you install your switch in a cabinet or install it directly on a workbench, you
must ensure:
l
Enough space is left near the air-intake hole
and the ventilation hole of the switch for the heat dissipation of the switch
chassis.
l
The cabinet or the workbench takes good ventilation
and heat dissipation system.
l
The cabinet or the workbench is solid enough to
bear the weight of the switch and the accessories.
l
The cabinet or the workbench is well grounded.
To ensure normal operation and to prolong
the life span of the switch, the following requirements on the installation
site must also be satisfied.
You should keep your equipment room within
the proper temperature and humidity ranges to ensure the normal operation and working
life of your switch. If the humidity in the equipment room is too high for a
long time, it may decrease the insulation attribute of insulating material or
even cause electric leakage of insulating material, and, sometimes, may change the
mechanical performance of material and cause the rustiness and corrosion of
metal parts. If the relative humidity is too low, the captive screws may become
loose due to the shrinking of insulation washers; in addition, electrostatic is
more likely to be produced in a dry environment, which may damage the circuit
of the switch. High temperature may cause even greater damage to the switch.
High temperature for a long time will speed up the aging of insulation
material, greatly lower the reliability of the switch and greatly reduce the life
span of the switch.
Dust is a potential hazard to the safe operation of the switch.
Falling on the equipment, it may cause electrostatic adsorption, and hence
result in poor contact of the metal connectors or connection points. This is
more likely to happen when the indoor relative humidity is low; in this case, it
may not only shorten the device’s working life, but also incur
communication failure. The requirements on dust content and particle diameter
in the equipment room are shown in the following table:
Table 2-1 Requirements on dust content in the equipment room
|
Physical active substance
|
Unit
|
Content
|
|
Dust particle
|
particle/m³
|
≤ 3 x 104 (No visible
dust on desk in three days)
|
