You can log into an S3100-52P Ethernet
switch in one of the following ways:
l
Logging in locally through the Console port
l
Telneting locally or remotely to an Ethernet
port
l
Telneting to the Console port using a modem
l
Logging into the Web-based network management
system
l
Logging in through NMS (network management station)
S3100-52P Ethernet switch support two types
of user interfaces: AUX and VTY.
Table 1-1 Description on user interface
|
User interface
|
Applicable user
|
Port used
|
Description
|
|
AUX
|
Users logging in through the Console port
|
Console port
|
Each switch can accommodate one AUX user.
|
|
VTY
|
Telnet users and SSH users
|
Ethernet port
|
Each switch can accommodate up to five
VTY users.
|
The AUX port and
the Console port of a H3C series Ethernet switch are the same port. You will be
in the AUX user interface if you log in through this port.
Two kinds of user interface index exist:
absolute user interface index and relative user interface index.
1)
The absolute user interface indexes are as
follows:
l
AUX user interface: 0
l
VTY user interfaces: Numbered after AUX user
interfaces and increases in the step of 1
2)
A relative user interface index can be obtained
by appending a number to the identifier of a user interface type. It is
generated by user interface type. The relative user interface indexes are as
follows:
l
AUX user interface: AUX 0
l
VTY user interfaces: VTY 0, VTY 1, VTY 2, and so
on.
Table 1-2 Common user interface
configuration
|
Operation
|
Command
|
Description
|
|
Lock the current user interface
|
lock
|
Optional
Execute this command in user view.
A user interface is not locked by
default.
|
|
Specify to send messages to all user
interfaces/a specified user interface
|
send { all
| number | type number }
|
Optional
Execute this command in user view.
|
|
Disconnect a specified user interface
|
free user-interface [ type ] number
|
Optional
Execute this command in user view.
|
|
Enter system view
|
system-view
|
—
|
|
Enter user interface view
|
user-interface [ type ] first-number [ last-number ]
|
—
|
|
Set the command that is automatically
executed when a user logs into the user interface
|
auto-execute command text
|
Optional
By default, no command is automatically
executed when a user logs into a user interface.
|
|
Display the information about the current
user interface/all user interfaces
|
display users [ all ]
|
Optional
You can execute the display
command in any view.
|
|
Display the physical attributes and configuration
of the current/a specified user interface
|
display user-interface [ type number | number ]
|
|
Display the information about the current
web users
|
display web users
|
Caution:
l
The auto-execute command command may
cause you unable to perform common configuration in the user interface, so use
it with caution.
l
Before executing the auto-execute command
command and save your configuration, make sure you can log into the switch in
other modes and cancel the configuration.
Chapter 2 Logging in through the Console
Port
To log in through the Console port is the
most common way to log into a switch. It is also the prerequisite to configure
other login methods. Normally, you can log into an S3100-52P Ethernet switch
through its Console port.
To log into an Ethernet switch through its
Console port, the communication configuration of the user terminal must be in
accordance with that of the Console port.
Table 2-1 lists the default settings of a Console port.
Table 2-1 The
default settings of a Console port
|
Setting
|
Default
|
|
Baud rate
|
9,600 bps
|
|
Flow control
|
None
|
|
Check mode (Parity)
|
None
|
|
Stop bits
|
1
|
|
Data bits
|
8
|
After logging into a switch, you can
perform configuration for AUX users. Refer to section 2.3
“Console Port Login Configuration” for more.
Following are the procedures to connect to
a switch through the Console port.
1)
Connect the serial port of your PC/terminal to
the Console port of the switch, as shown in Figure 2-1.
Figure 2-1 Diagram for setting the connection to the Console port
2)
If you use a PC to connect to the Console port,
launch a terminal emulation utility (such as Terminal in Windows 3.X or
HyperTerminal in Windows 9X) and perform the configuration shown in Figure 2-2 through Figure 2-4 for the connection to be created. Normally, the parameters of a terminal are configured as those listed in Table 2-1. And the type of the terminal is set to VT100.
Figure 2-2 Create a connection
Figure 2-3 Specify the port used to
establish the connection
Figure 2-4 Set port parameters
3)
Turn on the switch. You will be prompted to
press the Enter key if the switch successfully completes POST (power-on self
test). The prompt (such as <H3C>) appears after you press the Enter key.
4)
You can then configure the switch or check the
information about the switch by executing the corresponding commands. You can
also acquire help by typing the ? character. The commands available on a switch
are described in the command manuals.
Table 2-2 lists the common configuration of Console port login.
Table 2-2 Common
configuration of Console port login
|
Configuration
|
Remarks
|
|
Console
port configuration
|
Baud rate
|
Optional
The
default baud rate is 9,600 bps.
|
|
Check mode
|
Optional
By default, the check mode of the Console
port is set to “none”, which means no check bit.
|
|
Stop bits
|
Optional
The default stop bits of a Console port
is 1.
|
|
Data bits
|
Optional
The default data bits of a Console port
is 8.
|
|
AUX user interface configuration
|
Configure the command level available to
the users logging into the AUX user interface
|
Optional
By default, commands of level 3 are
available to the users logging into the AUX user interface.
|
|
Terminal configuration
|
Make terminal services available
|
Optional
By default, terminal services are
available in all user interfaces
|
|
Set the maximum number of lines the
screen can contain
|
Optional
By default, the screen can contain up to
24 lines.
|
|
Set history command buffer size
|
Optional
By default, the history command buffer
can contain up to 10 commands.
|
|
Set the timeout time of a user interface
|
Optional
The default timeout time is 10 minutes.
|
Caution:
Changing of Console
port configuration terminates the connection to the Console port. To establish
the connection again, you need to modify the configuration of the termination
emulation utility running on your PC accordingly. Refer to section 2.2 “Logging in through the Console Port” for more.
Table 2-3 lists Console port login configurations for different authentication modes.
Table 2-3 Console port login configurations for different authentication modes
|
Authentication mode
|
Console port login configuration
|
Remarks
|
|
None
|
Perform common configuration
|
Perform common configuration for Console
port login
|
Optional
Refer to section 2.3.1
“Common Configuration” for more.
|
|
Password
|
Configure
the password
|
Configure
the password for local authentication
|
Required
|
|
Perform common configuration
|
Perform common configuration for Console
port login
|
Optional
Refer to section 2.3.1
“Common Configuration” for more.
|
|
Scheme
|
Specify to perform local authentication
or RADIUS authentication
|
AAA configuration specifies whether to
perform local authentication or RADIUS authentication
|
Optional
Local authentication is performed by
default.
Refer to the AAA&RADIUS&HWTACACS&EAD
module for more.
|
|
Configure user name and password
|
Configure user names and passwords for
local/RADIUS users
|
Required
l The user name and password of a local user are configured on the
switch.
l The user name and password of a RADIUS user are configured on the RADIUS
server. Refer to user manual of RADIUS server for more.
|
|
Manage AUX users
|
Set service type for AUX users
|
Required
|
|
Perform common configuration
|
Perform common configuration for Console
port login
|
Optional
Refer to section 2.3.1
“Common Configuration” for more.
|
Changes of the
authentication mode of Console port login will not take effect unless you quit the
command-line interface and then enter it again.
Table 2-4 Console port login
configuration with the authentication mode being none
|
Operation
|
Command
|
Description
|
|
Enter system view
|
system-view
|
—
|
|
Enter AUX user interface view
|
user-interface aux 0
|
—
|
|
Configure not to authenticate users
|
authentication-mode none
|
Required
By default, users logging in through the
Console port are not authenticated.
|
|
Configure the Console port
|
Set the baud rate
|
speed speed-value
|
Optional
The default baud rate of an AUX port
(also the Console port) is 9,600 bps.
|
|
Set the check mode
|
parity { even
| none | odd }
|
Optional
By default, the check mode of a Console
port is set to none, that is, no check bit.
|
|
Set the stop bits
|
stopbits {
1 | 1.5 | 2 }
|
Optional
The stop bits of a Console port is 1.
|
|
Set the data bits
|
databits {
7 | 8 }
|
Optional
The default data bits of a Console port
is 8.
|
|
Configure the command level available to
users logging into the user interface
|
user privilege level level
|
Optional
By default, commands of level 3 are
available to users logging into the AUX user interface.
|
|
Make terminal services available
|
shell
|
Optional
By default, terminal services are
available in all user interfaces.
|
|
Set the maximum number of lines the
screen can contain
|
screen-length screen-length
|
Optional
By default, the screen can contain up to
24 lines.
You can use the screen-length 0
command to disable the function to display information in pages.
|
|
Set the history command buffer size
|
history-command max-size value
|
Optional
The default history command buffer size
is 10. That is, a history command buffer can store up to 10 commands by
default.
|
|
Set the timeout time for the user
interface
|
idle-timeout minutes [ seconds ]
|
Optional
The default timeout time of a user
interface is 10 minutes.
With the timeout time being 10 minutes, the
connection to a user interface is terminated if no operation is performed in
the user interface within 10 minutes.
You can use the idle-timeout 0
command to disable the timeout function.
|
Note that the command level available to
users logging into a switch depends on both the authentication-mode none
command and the user privilege level level command, as listed in the
following table.
Table 2-5 Determine the command level
(A)
|
Scenario
|
Command level
|
|
Authentication mode
|
User type
|
Command
|
|
None (authentication-mode none)
|
Users logging in through Console port
|
The user privilege level level
command not executed
|
Level 3
|
|
The user privilege level level
command already executed
|
Determined by the level argument
|
I. Network
requirements
Assume that you are a level 3 VTY user and
want to perform the following configuration for users logging in through the
Console port:
l
Do not authenticate users logging in through the
Console port.
l
Commands of level 2 are available to users
logging into the AUX user interface.
l
The baud rate of the Console port is 19,200 bps.
l
The screen can contain up to 30 lines.
l
The history command buffer can contain up to 20
commands.
l
The timeout time of the AUX user interface is 6
minutes.
II. Network
diagram
Figure 2-5 Network
diagram for AUX user interface configuration (with the authentication mode
being none)
III. Configuration
procedure
# Enter system view.
<H3C> system-view
# Enter AUX user interface view.
[H3C] user-interface aux 0
# Specify not to authenticate users logging
in through the Console port.
[H3C-ui-aux0] authentication-mode none
# Specify commands of level 2 are available
to users logging into the AUX user interface.
[H3C-ui-aux0] user privilege level 2
# Set the baud rate of the Console port to
19,200 bps.
[H3C-ui-aux0] speed 19200
# Set the maximum number of lines the
screen can contain to 30.
[H3C-ui-aux0] screen-length 30
# Set the maximum number of commands the
history command buffer can store to 20.
[H3C-ui-aux0] history-command
max-size 20
# Set the timeout time of the AUX user
interface to 6 minutes.
[H3C-ui-aux0] idle-timeout 6
Table 2-6 Console port login
configuration with the authentication mode being password
|
Operation
|
Command
|
Description
|
|
Enter system view
|
system-view
|
—
|
|
Enter AUX user interface view
|
user-interface aux 0
|
—
|
|
Configure to authenticate users using the
local password
|
authentication-mode password
|
Required
By default, users logging into a switch
through the Console port are not authenticated; while those logging in
through Modems or Telnet are authenticated.
|
|
Set the local password
|
set authentication password { cipher | simple } password
|
Required
|
|
Configure
the Console port
|
Set the
baud rate
|
speed speed-value
|
Optional
The default
baud rate of an AUX port (also the Console port) is 9,600 bps.
|
|
Set the check mode
|
parity { even
| none | odd }
|
Optional
By default, the check mode of a Console
port is set to none, that is, no check bit.
|
|
Set the stop bits
|
stopbits {
1 | 1.5 | 2 }
|
Optional
The default stop bits of a Console port
is 1.
|
|
Set the data bits
|
databits {
7 | 8 }
|
Optional
The default data bits of a Console port
is 8.
|
|
Configure the command level available to
users logging into the user interface
|
user privilege level level
|
Optional
By default, commands of level 3 are
available to users logging into the AUX user interface.
|
|
Make terminal services available to the
user interface
|
shell
|
Optional
By default, terminal services are
available in all user interfaces.
|
|
Set the maximum number of lines the
screen can contain
|
screen-length screen-length
|
Optional
By default, the screen can contain up to
24 lines.
You can use the screen-length 0
command to disable the function to display information in pages.
|
|
Set history command buffer size
|
history-command max-size value
|
Optional
The default history command buffer size
is 10. That is, a history command buffer can store up to 10 commands by
default.
|
|
Set the timeout time for the user
interface
|
idle-timeout minutes [ seconds ]
|
Optional
The default timeout time of a user
interface is 10 minutes.
With the timeout time being 10 minutes,
the connection to a user interface is terminated if no operation is performed
in the user interface within 10 minutes.
You can use the idle-timeout 0
command to disable the timeout function.
|
Note that the level the commands of which
are available to users logging into a switch depends on both the authentication-mode
password and the user privilege level level command, as
listed in the following table.
Table 2-7 Determine the command level
(B)
|
Scenario
|
Command level
|
|
Authentication mode
|
