Syntax
count times
undo count
View
HWPing test group view
Parameter
times:
Number of the test packets to be sent in each test. It is in the range 1 to 15
and defaults to 1.
Description
Use the count command to configure
the number of packets to be sent in each test.
Use the undo count command to
restore the default.
If this parameter is set to a number greater
than 1, the system sends the second test packet once it receives a response to
the first one, or when the test timer times out if it receives no response
after sending the first one, and so forth until the last test packet is sent
out.
Related command: frequency.
Example
# Set the “administrator-icmp”
test group to send 10 packets in each test.
<H3C> system-view
System View: return to User View
with Ctrl+Z.
[H3C] hwping administrator icmp
[H3C-hwping-administrator-icmp] count
10
Syntax
destination-ip ip-address
undo destination-ip
View
HWPing test group view
Parameter
ip-address:
Destination IP address in a test.
Description
Use the destination-ip command to configure
the destination IP address in the test. Use the undo destination-ip
command to remove the configured destination IP address.
By default, no destination IP address is
configured for any test.
Example
# Set the destination IP address in the
test of the “administrator-icmp” test group to 1.1.1.99.
<H3C> system-view
System View: return to User View with
Ctrl+Z.
[H3C] hwping administrator icmp
[H3C-hwping-administrator-icmp] destination-ip
1.1.1.99
Syntax
display hwping { results | history } [ administrator-name operation-tag
]
View
Any view
Parameter
results: Specifies
to display the test results.
history: Specifies
to display the test history.
administrator-name: Name of the administrator creating the test.
operation-tag: Test operation tag.
Description
Use the display hwping command to
view test result(s).
If a test group is specified using the
arguments of administrator-name and test-operation-tag, the
system displays only the test result of the group; if not, it displays the test
results of all the test groups.
Related command: test-enable.
Example
# Use the display hwping results command
to display the test result of the test group whose administrator name is
“administrator” and operation tag is “icmp”.
<H3C> display hwping results
administrator icmp
HWPing entry(admin administrator,
tag icmp) test result:
Destination ip address:1.1.1.99
Send operation times:
10 Receive response times: 10
Min/Max/Average Round Trip
Time: 2/5/2
Square-Sum of Round Trip Time:
66
Last complete test time:
2000-4-2 7:59:54.7
Extend result:
SD Maximal delay:
0 DS Maximal delay: 0
Packet lost in test: 0%
Disconnect operation number:
0 Operation timeout number: 0
System busy operation number:
0 Connection fail number: 0
Operation sequence errors:
0 Drop operation number: 0
Other operation errors: 0
Table 1-1
Description on the fields of the display hwping
results command
|
Field
|
Description
|
|
Destination ip address
|
Destination IP address
|
|
Send operation times
|
Number of send operations
|
|
Receive response times
|
Number of successful test operations
|
|
Min/Max/Average Round Trip Time
|
Smallest/biggest/average round-trip time
|
|
Square-Sum of Round Trip Time
|
The square sum of the round trip time
|
|
Last complete test time
|
Time of the last successful test
|
|
SD Maximal delay
|
Maximal delay from the source to the
destination
|
|
DS Maximal delay
|
Maximal delay from the destination to the
source
|
|
Packet lost in test
|
Packet lost ratio in the test.
|
|
Disconnect operation number
|
Number of forced disconnections by the opposite side
|
|
Operation timeout number
|
Number of timeout
times in the test operation
|
|
System busy operation number
|
Number of test
failures because the system is busy
|
|
Connection fail number
|
Number of connection failures
|
|
Operation sequence errors
|
Number of received sequence error packets
|
|
Drop operation number
|
Number of system resource allocation
errors
|
|
Other operation errors
|
Number of other errors
|
# Use the display hwping history command
to display test results.
<H3C> display hwping history
administrator icmp
HWPing entry(admin administrator,
tag icmp) history record:
Index Response Status
LastRC Time
1 1 1
0 2004-11-25 16:28:55.0
2 1 1
0 2004-11-25 16:28:55.0
3 1 1
0 2004-11-25 16:28:55.0
4 1 1
0 2004-11-25 16:28:55.0
5 1 1
0 2004-11-25 16:28:55.0
6 2
1 0 2004-11-25 16:28:55.0
7 1 1
0 2004-11-25 16:28:55.0
8 1 1 0
2004-11-25 16:28:55.0
9 1 1
0 2004-11-25 16:28:55.9
10 1 1
0 2004-11-25 16:28:55.9
Table 1-2
Description on the fields of the display hwping
history command
|
Field
|
Description
|
|
Index
|
Index of the displayed information
|
|
Response
|
Round trip test time, in milliseconds, or
the timeout time. 0 means the
test fails.
|
|
Status
|
Value of the test result. See the
following detailed description:
1: responceReceived. It means response is
received.
2: unknown. It means unknown error.
3: internalError. It means system
internal error.
4: requestTimeOut. It means timeout before
response.
5: unknownDestinationAddress. It means
the destination address is unknown.
6: noRouteToTarget. It means there is no
route to the destination address.
7: interfaceInactiveToTarget. It means
the interface of destination address is not activated.
8: arpFailure. It means ARP operation
fails.
9: maxConcurrentLimitReached. It means
the maximum limit of concurrent accesses is reached.
10: unableToResolveDnsName. It means it
is unable to resolve the DNS name.
11: invalidHostAddress. It means the
invalid host address.
|
|
LastRC
|
Receive the last response code based on
the implementation ways. With ICMP echo enabled, if
the system receives ICMP response which includes ICMP_ECHOREPLY(0), the probe
has succeeds. ICMP response often defined in the file containing ip_icmp.
|
|
Time
|
Test time
|
Syntax
frequency
interval
undo frequency
View
HWPing test group view
Parameter
interval:
Automatic test interval. It ranges from 0 to 65535 seconds and defaults to 0
seconds which means no automatic test.
Description
Use the frequency command to
configure an automatic test interval.
Use the undo frequency command to
disable automatic test.
The system automatically tests at intervals
specified by this command, where the argument interval is greater than
0.
Related command: count.
Example
# Set the automatic test interval of the “administrator-icmp”
test group to 10 seconds.
<H3C> system-view
System View: return to User View with
Ctrl+Z.
[H3C] hwping administrator icmp
[H3C-hwping-administrator-icmp] frequency
10
Syntax
hwping administrator-name
operation-tag
undo hwping
administrator-name operation-tag
View
System view
Parameter
administrator-name: Name of the administrator creating an HWPing test group, a string
of 1 to 32 characters.
operation-tag: Test operation tag, a string of 1 to 32 characters.
Description
Use the hwping command to create an HWPing
test group and enter HWPing test group view..
Use the undo hwping command to remove
the HWPing test group.
Example
# Create an HWPing test group, where the
administrator name is “administrator” and the test operation tag is
“icmp”.
<H3C> system-view
System View: return to User View with
Ctrl+Z.
[H3C] hwping administrator icmp
[H3C-hwping-administrator-icmp]
Syntax
hwping-agent enable
undo hwping-agent enable
View
System view
Parameter
None
Description
Use the hwping-agent enable command
to enable the HWPing client function.
Use the undo hwping-agent enable
command to disable the HWPing client function.
Before you can perform a test, you must
enable the HWPing client function.
Example
# Enable HWPing client.
<H3C> system-view
System View: return to User View with
Ctrl+Z.
[H3C] hwping-agent enable
Syntax
test-enable
undo test-enable
View
HWPing test group view
Parameter
None
Description
Use the test-enable command to
execute an HWPing test.
Use the undo test-enable command to disable
an HWPing test.
After you execute
the test-enable command, the system does not display the test result.
You may view the test result information by executing the display hwping
command.
Related command: display hwping.
Example
# Execute the HWPing test defined by the
test group “administrator-icmp”.
<H3C> system-view
System View: return to User View
with Ctrl+Z.
[H3C] hwping administrator icmp
[H3C-hwping-administrator-icmp]
test-enable
Syntax
test-type type
View
HWPing test group view
Parameter
type: Test
type.
Description
Use the test-type command to
configure the type of the test.
Currently the system only supports ICMP test.
Example
# Set the test type of the “administrator-icmp”
test group to ICMP.
<H3C> system-view
System View: return to User View with
Ctrl+Z.
[H3C] hwping administrator icmp
[H3C-hwping-administrator-icmp] test-type
icmp
Syntax
timeout
time
undo timeout
View
HWPing test group view
Parameter
time:
Timeout time. It ranges from 1 to 60 seconds and defaults to 3 seconds.
Description
Use the timeout command to configure
a timeout time for a test.
Use the undo timeout command to
restore to the default timeout time.
Example
# Set the timeout time of the “administrator-icmp”
test group to 10 seconds.
<H3C> system-view
System View: return to User View with
Ctrl+Z.
[H3C] hwping administrator icmp
[H3C-hwping-administrator-icmp] timeout
10
