Aolynk S1505L Smart Ethernet Switch
Quick Start-(V3.03)
1 Introduction
Aolynk S1505L Smart Ethernet Switch (hereinafter referred to as the S1505L) is oriented to small and medium-sized enterprise users and SOHO users for IPTV application. It provides five autosensing 10/100Base-TX Ethernet ports:
l Uplink port: Connected to carrier network
l VoIP port: Connected to IP phone
l TV port: Connected to IPTV set-top box
l PC port: Connected to PC
l EXP port: Expansion port (which can be used as the console port)
I. Front panel
Figure 1 shows the LEDs on the front panel of the S1505L: a power LED, pairs of speed and state LEDs, with each pair corresponding to one Ethernet port.
Figure 1 Front panel
II. Rear panel
Figure 2 shows the rear panel of the S1505L. On this panel, there are five autosensing 10/100Base-TX Ethernet ports, one Reset button (unavailable for the S1505L), and one power jack.
Figure 2 Rear panel
1.1 LED Description
Table 1 LED description
LED | Label | State | Description |
Power | Power | Green | The S1505L is powered on. |
OFF | The S1505L is powered off. |
Speed | Speed | Green | The port is operating at 100 Mbps. |
OFF | The port is operating at 10 Mbps, or no Ethernet link is present. |
State | Link/Act | Green | An Ethernet link is established. |
OFF | No Ethernet link is present. |
Blinking green | Data is being transmitted/received on the port. |
2 Hardware Installation
2.1 Packing List
l One Aolynk S1505L Smart Ethernet Switch
l One power adapter
l Aolynk S1505L Ethernet Switch Quick Start
l Warranty Card
l Certificate of Quality
If anything is missing or broken, please contact your agent for help.
2.2 Precautions
To make the S1505L operate normally and prolong its working life, take the following precautions:
l Use the S1505L only indoors, and place the S1505L in a dry and drafty area.
l Do not put the S1505L on an unsteady box or workbench. The S1505L may be damaged if it falls down.
l Reserve more than 10 cm (4 in.) of clearance around the S1505L for heat dissipation.
l Wire the interface cables of the S1505L indoors (outdoor wiring is not suggested), to prevent the signal ports of the device from damage due to over-voltage and over-current caused by thunder.
2.3 Connection
I. Connect your devices to the S1505L
The Ethernet ports on the S1505L support auto-MDI/MDIX, so you can use crossover or straight-through cables to connect your devices to the S1505L.
II. Connect the power adapter
(1) Attach one end of the power adapter to the S1505L and the other end to a power socket.
(2) Check the states of the LEDs.
Check the Power LED first. Solid ON indicates the S1505L is powered normally. After a few seconds, check the states of the LEDs corresponding to the ports connected to your devices. Normal LED states indicate the connections with your devices are normal.
3 Technical Specifications
Table 2 Technical Specifications
Item | Description |
Ports | Five autosensing 10/100Base-TX Ethernet ports |
Interface attributes | RJ-45 connector Compliant with IEEE 802.3, IEEE 802.3u and IEEE 802.3x 10/100 Mbps transmission rate Half duplex, full duplex and auto-negotiation Auto-MDI/MDIX |
Cable | 10Base-T: Category 3/4/5 shielded twisted pair (STP) with the maximum transmission distance of 100 m (328 ft) 100Base-TX: Category 5 STP with the maximum transmission distance of 100 m (328 ft) |
Physical dimensions (H ´ W ´ D) | 34 ´ 150 ´ 110 mm (1.3 ´ 5.9 ´ 4.3 in.) |
Weight | 300 g (10.6 oz) |
Input voltage | 12 VDC |
Power consumption | 4.5 W |
Operating temperature | 0°C to 40°C (32°F to 104°F) |
Storage temperature | –10°C to +70°C (14°F to 158°F) |
Operating humidity (noncondensing) | 20% to 85% |
Storage humidity (noncondensing) | 10% to 90% |
System cooling | Air cooling |
Huawei Technologies Co., Ltd.
Technical Support:
Address: 310 Liuhe Road, Zhijiang Science Park,
Hangzhou 310053, P. R. China
Postal Code: 310053
Website: http://www.h3c.com
E-mail: soho@h3c.com
