|
00-1Cover
|
|
|
|
|
|
|
|
|
Comware V3
|
|
Command Manual
|
|
|
|
|
|
|
|
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Manual Version:
T2-08192H-20080114-C-3.07
|
Copyright
© 2003-2008, Hangzhou H3C Technologies Co., Ltd. and its licensors
All Rights Reserved
No part of this manual may be reproduced
or transmitted in any form or by any means without prior written consent of Hangzhou
H3C Technologies Co., Ltd.
Trademarks
H3C,  , Aolynk,  , H3Care,  , TOP G,  , IRF, NetPilot, Neocean, NeoVTL, SecPro,
SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V2G,
VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks
of Hangzhou H3C Technologies Co., Ltd.
All other trademarks that may be mentioned
in this manual are the property of their respective owners.
Notice
The information in this document is
subject to change without notice. Every effort has been made in the preparation
of this document to ensure accuracy of the contents, but all statements,
information, and recommendations in this document do not constitute the
warranty of any kind, express or implied.
To obtain the latest information, please
access:
http://www.h3c.com
Technical
Support
customer_service@h3c.com
http://www.h3c.com
About
This Manual
Related
Documentation
In addition
to this manual, each related documentation set includes the following:
|
Manual
|
Description
|
|
Comware V3 Operation Manual
|
The manual is a guide for the user to
perform the operations correctly. It is organized into the parts of getting
started, system management, interface, link layer protocol, network protocol,
routing protocol, multicast protocol, security, VPN, reliability, QoS, MPLS,
dial-up and Non-IP Architecture, as well as acronyms used in the manual.
|
|
Low-End and Mid-Range Series Routers
Terminal Access User Manual
|
The manual gives the user a guide and
related commands to operate terminal access.
|
Organization
Comware V3 Command Manual is organized as follows:
|
Part
|
Contents
|
|
1. Getting Started
|
introduces Comware V3 user interface configuration commands.
|
|
2. System Management
|
introduces the configuration commands of system maintenance
management, file management, user interface configuration, NTP configuration,
SNMP configuration and terminal services.
|
|
3. Interface
|
introduces the configuration commands of LAN interface,
synchronous/asynchronous serial interface, CE1 interface, subinterface,
virtual interface template and virtual Ethernet interface.
|
|
4. Link Layer Protocol
|
introduces the configuration commands of PPP, MP, PPPoE, SLIP,
ISDN, VLAN, HDLC, Frame Relay, ATM, LAPB and X.25.
|
|
5. Network Protocol
|
introduces the configuration commands IP address, static address
resolution, domain name resolution, IP performance, IP unicast policy
routing, IP multicast policy routing and DLSw.
|
|
6. Routing Protocol
|
introduces the configuration commands of static routing, RIP,
OSPF, IS-IS, BGP, MBGP, IP routing policy and IP route capacity.
|
|
7. Multicast Protocol
|
introduces the configuration
commands of common multicast, IGMP, PIM DM, PIM SM, MSDP, MBGP and multicast
static routing.
|
|
8. MPLS
|
introduces MPLS configuration
commands.
|
|
9. Security
|
introduces the configuration
commands of AAA, RADIUS, firewall, NAT, IPSec and IKE.
|
|
10. VPN
|
introduces the configuration
commands of L2TP, GRE, BGP/MPLS VPN and MPLS L2VPN.
|
|
11. QoS
|
introduces the configuration
commands of traffic classification, traffic policing, traffic shaping,
congestion management and congestion avoidance.
|
|
12. Reliability
|
introduces the configuration commands of standby center and VRRP.
|
|
13. Dial-up
|
introduces the configuration commands of DCC and modem.
|
|
14. Voice
|
introduces the configuration commands for implementing voice and
fax services on IP networks, such as VoIP, E1/T1, fax, voice RADIUS, GK
client, and SIP client.
|
|
15. Non-IP Architecture
|
introduces the configuration commands of OSI, IPX and DLSw.
|
|
16. Command Index
|
lists all the commands that appear in the manuals.
|
Conventions
The manual uses the following conventions:
I. Command
conventions
|
Convention
|
Description
|
|
Boldface
|
The keywords of a command line are in Boldface.
|
|
italic
|
Command arguments are in italic.
|
|
[ ]
|
Items (keywords or arguments) in square brackets [ ] are optional.
|
|
{ x | y | ... }
|
Alternative items are grouped in braces and separated by vertical
bars. One is selected.
|
|
[ x | y | ... ]
|
Optional alternative items are grouped in square brackets and
separated by vertical bars. One or none is selected.
|
|
{ x | y | ... } *
|
Alternative items are grouped in braces and separated by vertical
bars. A minimum of one or a maximum of all can be selected.
|
|
[ x | y | ... ] *
|
Optional alternative items are grouped in square brackets and
separated by vertical bars. Many or none can be selected.
|
|
&<1-n>
|
The argument(s) before the ampersand (&) sign can be entered 1
to n times.
|
|
#
|
A line starting with the # sign is comments.
|
II. GUI conventions
|
Convention
|
Description
|
|
< >
|
Button names are inside angle brackets. For example, click
<OK>.
|
|
[ ]
|
Window names, menu items, data table and field
names are inside square brackets. For example, pop up the [New User] window.
|
|
/
|
Multi-level menus are separated by forward
slashes. For example, [File/Create/Folder].
|
III. Symbols
|
Convention
|
Description
|
|
 Warning
|
Means reader be
extremely careful. Improper operation may cause bodily injury.
|
|
 Caution
|
Means reader be careful. Improper operation may
cause data loss or damage to equipment.
|
|
& Note
|
Means a complementary description.
|
|
|
