- Released At: 06-01-2020
- Page Views:
- Downloads:
- Table of Contents
- Related Documents
-
About the H3C S12500-X & S12500X-AF command references
CAUTION: · Software Release 11xx applies only to F-series LPUs, which have an F in their card identifiers (for example, LSXM1TGS48FX1). S12500-X E-series LPUs (for example, LSX2TGS48EA1) or S12500X-AF H-series LPUs (for example, LSXM1CGQ36HB1) cannot run the software. · Do not install an F-series LPU and an E-series LPU on the same S12500-X switch. Do not install an F-series LPU and an H-series LPU on the same S12500X-AF switch. |
The H3C S12500-X & S12500X-AF command references describe the commands and command syntax options available for the H3C S12500-X & S12500X-AF Switch Series running Release 1150 and later.
Command reference |
Content |
Fundamentals Command Reference |
Covers the commands for logging in to and setting up the switch. This command reference includes: · Basic CLI · Login management · RBAC · FTP and TFTP · File system management · Configuration file management · Software upgrade · ISSU · Device management · Python · License · Preprovisioning |
Virtual Technologies Command Reference |
Covers the commands for configuring the virtual technologies. This command reference includes: · IRF · MDC |
Layer 2—LAN Switching Command Reference |
Covers the commands for configuring Layer 2 technologies and features in a LAN switched network. This command reference includes: · Ethernet interface · Loopback, null, and inloopback interface · Bulk interface configuration · MAC address table and MAC Information · Ethernet link aggregation · Port isolation · Spanning tree · Loop detection · VLAN · VLAN mapping · LLDP · Service loopback group |
Layer 3—IP Services Command Reference |
Covers the commands for configuring IP addressing, IP performance optimization, ARP, IP forwarding basic, DHCP, DNS, UDP helper, IPv6,Tunnel, GRE and DHCPv6. This command reference includes: · ARP (including gratuitous ARP and proxy ARP) · IP addressing · DHCP · DNS · Basic IP forwarding and load sharing · IRDP · IP performance optimization · UDP helper · IPv6 · DHCPv6 · Tunnel · GRE |
Layer 3—IP Routing Command Reference |
Covers the commands for configuring routes for IPv4 networks of different sizes. This command reference includes: · Basic IP routing · Static routing · RIP · OSPF · IS-IS · BGP · Policy-based routing · IPv6 static routing · RIPng · OSPFv3 · IPv6 IS-IS · IPv6 Policy-based routing · Routing policy |
IP Multicast Command Reference |
Covers the commands for Layer 3 IPv4 multicast protocols (IGMP and PIM), Layer 2 IPv4 multicast protocols (IGMP snooping) and Layer 2 IPv6 multicast protocols (MLD snooping). This command reference includes: · IGMP snooping · Multicast routing and forwarding · IGMP · PIM · MSDP · MLD Snooping |
MPLS Command Reference |
Covers the commands for configuring basic MPLS and extended MPLS functions. This command reference includes: · Basic MPLS · LDP · MPLS TE · Static CRLSP · RSVP · Tunnel policy · MPLS L3VPN · MCE (including MCE and IPv6 MCE) |
ACL and QoS Command Reference |
Covers the commands for classifying traffic with ACLs, and allocating network resources and managing congestions with QoS technologies to improve network performance and network use efficiency. This command reference includes: · ACL · QoS, including the following: ? QoS policy ? Priority mapping ? Congestion management · Time range · Data buffer |
Security Command Reference |
Covers security feature commands. Available security features include identity authentication, secure management, and attack protection. This command reference includes: · AAA · Password control · PKI · SSL · IPsec and IKE · SSH · IP source guard · ARP attack protection · uRPF · FIPS · Attack detection and prevention |
High Availability Command Reference |
Covers high availability commands for managing failure detection and failover. Failure detection technologies focus on fault detection and isolation. Failover technologies focus on network recovery. This command reference includes: · Ethernet OAM · DLDP · RRPP · VRRP · BFD · Track |
Network Management and Monitoring Command Reference |
Covers the commands that help you manage and monitor your network, for example, manage system events, and test network connectivity. This command reference includes: · System maintenance and debugging (ping, tracert, and system debugging) · RMON · Sampler · Mirroring (including both port and traffic mirroring) · sFlow · EAA · NQA · NETCONF |
FCoE Command Reference |
Covers the commands for configuring FCoE. |
TRILL Command Reference |
Covers the commands for configuring TRILL. |
SPB Command Reference |
Covers the commands for configuring SPB. |
EVI Command Reference |
Covers the commands for configuring EVI. |
OpenFlow Command Reference |
Covers the commands for configuring OpenFlow. |
VXLAN Command Reference |
Covers the commands for configuring VXLAN. |