00-About the H3C S9820-8C Command References

HomeSupportSwitchesS9820 SeriesReference GuidesCommand ReferencesH3C S9820-8C Switch Command References-Release 66xx-6W10300-About the H3C S9820-8C Command References
Download Book
  • Released At: 12-06-2022
  • Page Views:
  • Downloads:
Table of Contents
Related Documents

About the H3C S9820-8C command references

The H3C S9820-8C command references describe the commands and command syntax options available for the H3C S9820-8C switch in the following software versions:

·     Release 6607.

·     Release 6616.

·     Release 6616P01.

·     Release 6635 and later.

 

Command reference

Content

Fundamentals Command Reference

Covers the commands for logging in to and setting up the S9820-8C switch.

This command reference includes:

·     CLI.

·     RBAC.

·     Logging in to the switch.

·     FTP and TFTP.

·     File system management.

·     Configuration file management.

·     Software upgrade.

·     Preprovisioning.

·     Device management.

·     Tcl.

·     Python.

·     GIR.

Layer 2—LAN Switching Command Reference

Covers the commands for configuring Layer 2 technologies and features in a LAN switched network.

This command reference includes:

·     MAC address table and MAC Information.

·     Bulk interface configuration.

·     Ethernet interface.

·     Ethernet link aggregation.

·     DRNI.

·     Port isolation.

·     VLAN (including super VLAN).

·     MVRP.

·     Loopback, null, and inloopback interfaces.

·     Loop detection.

·     Spanning tree.

·     LLDP.

·     L2PT.

·     Service loopback group.

·     Cut-through Layer 2 forwarding.

Layer 3—IP Services Command Reference

Covers the commands for configuring and managing IP addressing (including static and dynamic IPv4 and IPv6 address assignment), network performance optimization, ARP, and interoperation between IPv4 and IPv6.

This command reference includes:

·     ARP (ARP, gratuitous ARP, proxy ARP, ARP snooping, ARP fast reply, and ARP direct route advertisement).

·     IP addressing.

·     DHCP.

·     DNS and DDNS.

·     IP forwarding basics and load sharing.

·     Fast forwarding.

·     Adjacency table.

·     IRDP.

·     IP performance optimization.

·     UDP Helper.

·     IPv6 basics.

·     DHCPv6.

·     IPv6 fast forwarding.

·     Tunneling.

·     GRE.

·     HTTP redirect.

Layer 3—IP Routing Command Reference

Covers the commands for configuring routes for IPv4 and IPv6 networks of different sizes, route filtering, route control, and policy based routing.

This command reference includes:

·     Basic IP routing.

·     Static routing.

·     RIP.

·     OSPF.

·     IS-IS.

·     BGP.

·     Policy-based routing.

·     IPv6 static routing.

·     RIPng.

·     OSPFv3.

·     IPv6 policy-based routing.

·     Routing policy.

IP Multicast Command Reference

Covers the commands for Layer 2 IPv4 multicast protocols (including IGMP snooping, and multicast VLAN), Layer 3 IPv4 multicast protocols (including IGMP and PIM), Layer 2 IPv6 multicast protocols (including MLD snooping and IPv6 multicast VLAN), and Layer 3 IPv6 multicast protocols (including MLD, IPv6 PIM, and MSDP).

This command reference includes:

·     IGMP snooping.

·     PIM snooping.

·     Multicast VLAN.

·     Multicast routing and forwarding.

·     IGMP.

·     PIM.

·     MSDP.

·     MLD snooping.

·     IPv6 PIM snooping.

·     IPv6 multicast VLAN.

·     IPv6 multicast routing and forwarding.

·     MLD.

·     IPv6 PIM.

MPLS Command Reference

Covers the MPLS commands.

This command reference includes:

·     Basic MPLS.

·     Static LSP.

·     LDP.

·     Tunnel policy.

·     MPLS L3VPN and IPv6 MPLS L3VPN.

·     MCE and IPv6 MCE.

ACL and QoS Command Reference

Covers the commands for classifying traffic with ACLs, and allocating network resources and managing congestions with QoS technologies to improve network performance and network use efficiency.

This command reference includes:

·     ACL.

·     QoS, including commands for the following features:

¡     QoS policy.

¡     Priority mapping.

¡     GTS and rate limit.

¡     Congestion management.

¡     Congestion avoidance.

¡     Aggregate CAR.

¡     QPPB.

¡     Control plane packet-drop logging.

·     Data buffer.

·     Time range.

Security Command Reference

Covers security feature commands. Available security features include identity authentication, secure management, and attack protection.

This command reference includes:

·     AAA.

·     802.1X.

·     MAC authentication.

·     Portal.

·     Web authentication.

·     Port security.

·     Password control.

·     Keychain.

·     Public key management.

·     PKI.

·     IPsec, IKE, and IKEv2.

·     SSH.

·     SSL.

·     Attack detection and prevention.

·     TCP attack prevention.

·     IP source guard.

·     ARP attack protection.

·     ND attack defense.

·     MFF.

·     Crypto engine.

·     FIPS.

·     Object group.

·     SAVI.

·     SAVA.

High Availability Command Reference

Covers high availability commands for managing failure detection and failover. Failure detection technologies focus on fault detection and isolation. Failover technologies focus on network recovery.

This command reference includes:

·     Ethernet OAM.

·     CFD.

·     DLDP.

·     RRPP.

·     ERPS.

·     Smart Link.

·     Monitor Link.

·     VRRP.

·     BFD.

·     Track.

Network Management and Monitoring Command Reference

Covers the commands that help you manage and monitor your network, for example, manage system events and test network connectivity.

This command reference includes:

·     System maintenance and debugging (ping, tracert, and system debugging).

·     NQA.

·     NTP and SNTP.

·     PTP.

·     SNMP.

·     RMON.

·     Event MIB.

·     NETCONF.

·     CWMP.

·     EAA.

·     Process monitoring and maintenance.

·     Sampler.

·     Mirroring (including port mirroring and flow mirroring).

·     NetStream.

·     IPv6 NetStream.

·     sFlow.

·     Information center.

·     GOLD.

·     Packet capture.

·     iNQA.

·     Packet trace.

·     NetAnalysis.

Telemetry Command Reference

Covers the commands that help you configure telemetry.

This command reference includes:

·     gRPC.

·     INT.

·     Telemetry stream.

·     Flow group.

·     MOD.

OpenFlow Command Reference

Covers the commands for configuring OpenFlow.

 

 

  • Cloud & AI
  • InterConnect
  • Intelligent Computing
  • Security
  • SMB Products
  • Intelligent Terminal Products
  • Product Support Services
  • Technical Service Solutions
All Services
  • Resource Center
  • Policy
  • Online Help
All Support
  • Become a Partner
  • Partner Resources
  • Partner Business Management
All Partners
  • Profile
  • News & Events
  • Online Exhibition Center
  • Contact Us
All About Us
新华三官网