- Released At: 18-11-2019
- Page Views:
- Downloads:
- Table of Contents
- Related Documents
-
1 Card identifier
The card identifier LSQM1MPUSC0 is in the upper right corner of the front panel.
2 Specifications
Table 1 Card specifications
Item | Specification |
Flash | 2 GB |
BootROM | 8 MB |
NVRAM | 1 MB |
SDRAM (DDR3) | 4 GB |
Card size (H × W × D) | 45 × 399 × 355 mm (1.77 × 15.71 × 13.98 in) |
Power consumption | 103 W to 168W |
Interfaces | · 1 console port · 1 USB console port · 4 network management ports: 2 RJ-45 ports and 2 SFP fiber ports · 1 primary USB port |
Transmission rate | · Console port: 9600 bps to 115200 bps (default: 9600 bps) · USB console port: ≤ 115200 bps (default: 9600 bps) · network management ports ( RJ-45 ): 10/100/1000 Mbps, half/full duplex · network management ports (SFP ): 1000 Mbps |
Transmission medium and max transmission distance | · Console port: 15 m (49.21 ft) over asynchronous EIA/TIA-232 cables · USB console port: 10 m (32.81 ft) over USB-AB cables · network management ports ( RJ-45 ): 100 m (328.08 ft) over Category 5 or higher twisted pair cables · network management ports (SFP ): see Table 3 |
Compatible device models | S7506X/S7506X-PoE |
Software version | Version 7568 and later |
| NOTE: H3C recommends not using a USB extender cable to connect the USB port. |
The 10/100/1000BASE-T copper port uses an RJ-45 connector.
Figure 1 RJ-45 connector
Table 2 RJ-45 GE connector pinout
Pin | 10BASE-T/100BASE-TX/1000BASE-T | |
Signal | Function | |
1 | MX_0+ | Transmits and receives data. |
2 | MX_0- | Transmits and receives data. |
3 | MX_1+ | Transmits and receives data. |
4 | MX_2+ | Transmits and receives data. |
5 | MX_2- | Transmits and receives data. |
6 | MX_1- | Transmits and receives data. |
7 | MX_3+ | Transmits and receives data. |
8 | MX_3- | Transmits and receives data. |
Table 3 describes the SFP transceiver modules available for the SFP and SFP+ ports on the card.
Table 3 GE SFP transceiver modules available for the SFP and SFP+ ports
GE SFP transceiver module | Central wavelength | Connector type | Cable specifications | Maximum transmission distance |
SFP-GE-SX-MM850-A | 850 nm | LC | 50/125 μm multi-mode optical fiber (MMF) | 550 m (0.34 miles) |
62.5/125 μm MMF | 275 m (0.17 miles) | |||
SFP-GE-SX-MM850-D | 850 nm | LC | 50/125 μm MMF | 550 m (0.34 miles) |
62.5/125 μm MMF | 275 m (0.17 miles) | |||
SFP-GE-LX-SM1310-A | 1310 nm | LC | 9/125 μm single-mode optical fiber (SMF) | 10 km (6.21 miles) |
50/125 μm MMF | 550 m (1804.46 ft) | |||
62.5/125 μm MMF | 550 m (1804.46 ft) | |||
SFP-GE-LX-SM1310-D | 1310 nm | LC | 9/125 μm SMF | 10 km (6.21 miles) |
50/125 μm MMF | 550 m (1804.46 ft) | |||
62.5/125 μm MMF | 550 m (1804.46 ft) | |||
SFP-GE-LH40-SM1310 | 1310 nm | LC | 9/125 μm SMF | 40 km (24.86 miles) |
SFP-GE-LH40-SM1310-D | 1310 nm | LC | 9/125 μm SMF | 40 km (24.86 miles) |
SFP-GE-LH40-SM1550 | 1550 nm | LC | 9/125 μm SMF | 40 km (24.86 miles) |
SFP-GE-LH80-SM1550 | 1550 nm | LC | 9/125 μm SMF | 80 km (49.71 miles) |
SFP-GE-LH80-SM1550-D | 1550nm | LC | 9/125 μm SMF | 80 km (49.71 miles) |
SFP-GE-LH100-SM1550 | 1550 nm | LC | 9/125 μm SMF | 100 km (62.14 miles) |
SFP-GE-LX-SM1310-BIDI | RX: 1490 nm TX: 1310 nm | LC | 9/125 μm SMF | 10 km (6.21 miles) |
SFP-GE-LX-SM1490-BIDI | RX: 1310 nm TX: 1490 nm | LC | 9/125 μm SMF | 10 km (6.21 miles) |
| NOTE: · BIDI modules use different central wavelengths in transmit and receive directions, in order to implement bidirectional transmission of optical signals over the same fiber. · The BIDI modules must be used in pairs. For example, if you install the SFP-GE-LX-SM1310-BIDI in the local port, you must install the SFP-GE-LX-SM1490-BIDI in the peer port. |
3 Related documentation
For module installation, see H3C S7500X Switch Series Installation Guide.
For software upgrade, see the release notes for the device.
Copyright © 2017-2018 New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.