- Released At: 31-10-2021
- Page Views:
- Downloads:
- Table of Contents
- Related Documents
-
LSXM1YGS24CGMODTE2 24-port 25G Ethernet optical interface (SFP28)+ 4-port 100G Ethernet optical interface module (QSFP28) with 1 expansion slot
1 Identifier
The module identifier LSXM1YGS24CGMODTE2 is marked on the right ejector lever pillow block on the front panel.
2 Specifications
Multiple interface cards are available for the expansion slot on the LSXM1YGS24CGMODTE2 interface module. The following figure uses an LSWM18QC interface card as an example.
Figure 1 Front panel
(1) SFP28 port |
(2) QSFP28 port |
(3) Expansion slot |
(4) Ejector lever |
(5) QSFP28 port LED |
(6) SFP28 port LED |
Item |
Specification |
Processor |
Quad-core @ 2.2 GHz |
SDRAM |
8 GB |
Power consumption |
210 W to 483 W |
Fixed ports |
· 24 × 25G SFP28 ports · 4 × 100G QSFP28 ports |
Transmission rate of the fixed ports |
· SFP28 port: 25 Gbps · QSFP28 port: 100 Gbps |
Expansion slot |
1 × expansion slot for interface card installation The interface card in the expansion slot needs to be ordered separately. For the available interface cards, see Table 2. For transceiver modules and cables available for ports on the interface card in the expansion slot, see the interface card manual. |
IMPORTANT: · This module can be used only with Type T fabric modules (such as LSXM1SFT08F2) and Type T supervisor engine units (such as LSXM2SUPT2). · To verify the compatibility of the module with the product models and software releases, see the release notes. · For the transceiver modules or cables available for the module, see the modules and transceiver modules compatibility matrixes for the device. |
Table 2 Interface cards available for the expansion slot
Interface card model |
Description |
LSWM18QC |
8-port QSFP+ interface card |
24-port SFP+ and 2-port QSFP+ interface card with MACSec |
|
LSWM124TG2H |
24-port 25G Ethernet optical interface (SFP28) and 2-port 100G Ethernet optical interface (QSFP28) module |
LSWM124XGT2Q |
24-port 10GBASE-T and 2-port QSFP+ interface card with MACSec |
LSWM1FWD0 |
Interface card that provides one console port, one USB port, and two network management ports (one RJ-45 and one SFP) |
|
NOTE: For software support of MACSec, see the release notes. |
3 Installing an interface card in the expansion slot
IMPORTANT: To install an interface card in the device, make sure the LSXM1YGS24CGMODTE2 module is installed in the device and the ejector lever of the module is closed. |
To install an interface card in the expansion slot:
1. Put your thumb and forefinger into the holes in the filler panel. Pressing the spring tab in the left hole rightward with your thumb, pull the filler panel out of the slot.
Figure 2 Removing the filler panel from the expansion slot
2. Unpack the interface card and press the latch to release the ejector lever.
3. As shown by callout 1 in Figure 3, insert the interface card slowly into the slot along the guide rails.
4. As shown by callout 2 in Figure 3, close the ejector lever. The latch automatically locks the ejector lever and secures the card into place.
Figure 3 Installing an interface card in the expansion slot
4 Related documentation
For information about installing the module, see the installation guide for the device.
For information about upgrading the system software, see the release notes for the device.
Copyright © 2021 New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.