H3C LSXM1SUPS2 Card Manual-APW100

HomeSupportSwitchesS12500G-AF SeriesInstall & UpgradeMPU Card ManualsH3C LSXM1SUPS2 Card Manual-APW100
Download Book
  • Released At: 08-05-2021
  • Page Views:
  • Downloads:
Table of Contents
Related Documents

LSXM1SUPS2 supervisor engine unit

1  Identifier

The module identifier LSXM1SUPS2 is in the upper right corner of the front panel.

2  Specifications

Table 1 Module specifications

Item

Specification

Processor main frequency

1 GHz

SDRAM

2 GB

Flash

1 GB

BootROM

16 MB

NVRAM

1 MB

Dimensions (H × W × D)

44 × 433 × 512 MM (1.73 × 17.05 × 20.16 in)

Power consumption

34 W to 40 W

Interfaces

·         1 × console port

·         1 × USB console port

·         1 × USB port

·         2 × network management ports (one RJ-45 port and one SFP port)

Transmission rate

·         Console port: 9600 (default) to 115200 bps

·         USB Console port: ≤ 115200 bps ( default: 9600 bps)

·         RJ-45 network management port: 10/100/1000 Mbps, half/full duplex

·         SFP network management port: 1000 Mbps

Available cable and maximum transmission distance

·         Console port: 15 m (49.21 ft) over an asynchronous EIA/TIA-232 cable

·         USB console port: 10 m (32.81 ft ) over a USB A-B cable

·         RJ-45 network management port: 100 m ( 328.08 ft ) over a Category 5 or above twisted pair cable

·         SFP network management port: GE SFP transceiver module

Compatible interface modules

Type S interface modules

Compatible fabric modules

Type S fabric modules

 

IMPORTANT

IMPORTANT:

·      This module can be used only with Type S fabric modules (such as LSXM1SFS08D2) and Type S interface modules (such as LSXM1TGS48SE2).

·      To verify the compatibility of the module with the product models and software releases, see the release notes.

·      For information about transceiver modules and cables available for the module, see the modules and transceiver modules compatibility matrixes for the device.

·      Before connecting the SFP network management port, make sure the peer Ethernet port operates at 1000 Mbps in full duplex mode.

·      The USB port does not support USB extension cables.

 

The 10/100/1000BASE-T copper port uses an RJ-45 connector.

Figure 1 RJ-45 connector

 

Table 2 RJ-45 GE connector pinout

Pin

10BASE-T/100BASE-TX/1000BASE-T

Signal

Function

1

MX_0+

Transmits and receives data.

2

MX_0-

Transmits and receives data.

3

MX_1+

Transmits and receives data.

4

MX_2+

Transmits and receives data.

5

MX_2-

Transmits and receives data.

6

MX_1-

Transmits and receives data.

7

MX_3+

Transmits and receives data.

8

MX_3-

Transmits and receives data.

 

3  Related documentation

For information about installing the module, see the installation guide for the device.

For information about upgrading system software, see the release notes.

 

 

Copyright © 2021 New H3C Technologies Co., Ltd.

The information in this document is subject to change without notice.

 

  • Cloud & AI
  • InterConnect
  • Intelligent Computing
  • Security
  • SMB Products
  • Intelligent Terminal Products
  • Product Support Services
  • Technical Service Solutions
All Services
  • Resource Center
  • Policy
  • Online Help
All Support
  • Become a Partner
  • Partner Resources
  • Partner Business Management
All Partners
  • Profile
  • News & Events
  • Online Exhibition Center
  • Contact Us
All About Us
新华三官网