• 产品与解决方案
  • 行业解决方案
  • 服务
  • 支持
  • 合作伙伴
  • 新华三人才研学中心
  • 关于我们

10-OAA命令参考

目录

01-OAA命令

本章节下载 01-OAA命令  (93.08 KB)

docurl=/cn/Service/Document_Software/Document_Center/Wlan/WX/H3C_WX3000/Command/Command_Manual/H3C_CR(E3703P61_R2509P61_R3709P61)-6W108/10/201707/1012832_30005_0.htm

01-OAA命令


1 OAP单板

说明

OAP单板配置命令的支持情况与设备的型号有关,请参见“命令参考导读”中的“命令行及参数差异情况”部分的介绍。

 

1.1  OAP单板配置命令

1.1.1  oap connect

【命令】

oap connect slot slot-number

【视图】

用户视图

【缺省级别】

1:监控级

【参数】

slot slot-number:OAP单板所在的槽位号。

【描述】

oap connect命令用来从设备侧重定向到OAP单板。

按快捷键<Ctrl+k>可以从OAP单板的操作系统返回到设备命令行操作界面。

【举例】

# 从设备侧重定向到0号槽位的OAP单板。

<Sysname> oap connect slot 0

Press CTRL+K to quit.

Connected to OAP!

1.1.2  oap management-ip

【命令】

oap management-ip ip-address slot slot-number

undo oap management-ip slot slot-number

【视图】

系统视图

【缺省级别】

2:系统级

【参数】

ip-address:OAP单板的管理IP地址。该地址必须是OAP单板上已经配置好的地址。

slot slot-number:OAP单板所在的槽位号。

【描述】

oap management-ip命令用来配置OAP单板的管理IP地址。undo oap management-ip命令用来恢复缺省情况。

缺省情况下,OAP单板没有配置管理IP地址。

当使用网络管理服务器(NMS)管理OAP单板时,需要设置OAP单板的管理IP地址。

【举例】

# 设置0号槽位的OAP单板的管理IP地址为1.1.1.1。

<Sysname> System-view

[Sysname] oap management-ip 1.1.1.1 slot 0

1.1.3  oap reboot

【命令】

oap reboot slot slot-number

【视图】

用户视图

【缺省级别】

3:管理级

【参数】

slot slot-number:OAP单板所在的槽位号。

【描述】

oap reboot命令用来配置重启OAP单板。

【举例】

# 复位0号槽位的OAP单板系统。

<Sysname> oap reboot slot 0

This command will recover the OAP from shutdown or other failed state.

Warning: This command may lose the data on the hard disk if the OAP is not being shut down!

Continue? [Y/N]:y

Reboot OAP by command.

 

不同款型规格的资料略有差异, 详细信息请向具体销售和400咨询。H3C保留在没有任何通知或提示的情况下对资料内容进行修改的权利!

新华三官网
联系我们